Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. madedi123
    • Profile
    • Following 1
    • Followers 0
    • Topics 9
    • Posts 50
    • Best 0
    • Controversial 1
    • Groups 0

    madedi123

    @madedi123

    -1
    Reputation
    1
    Profile views
    50
    Posts
    0
    Followers
    1
    Following
    Joined Last Online

    madedi123 Unfollow Follow

    Best posts made by madedi123

    • RE: ESP8266 NeoPixel Driver

      Hello

      My problem is that my pendant (the same as david's, with an arduino micro) only sends the M112 command, but does not perform any movement via the encoder. My hardware is a DUET3 6HC with SBC and without Panel DUE, Configuration CNC. The arduino sketch was uploaded with firmware 1.8.1 thank you for your help

      posted in Accessories and Add-ons
      madedi123undefined
      madedi123

    Latest posts made by madedi123

    • Pendant/dwc to hundredth

      Hi

      i use a duet3 sbc on a cnc mill, my question is how can i set up dwc on the x and y axies to hundredth of a mm and i will do the same on the same pendant like david`s ?
      thanks for help

      posted in CNC
      madedi123undefined
      madedi123
    • RE: CNC Pendant Disconnecting Duet

      it works fine. thank you

      posted in CNC
      madedi123undefined
      madedi123
    • RE: CNC Pendant Disconnecting Duet

      I will test it! Top David thank you!

      posted in CNC
      madedi123undefined
      madedi123
    • RE: CNC Pendant Disconnecting Duet

      i think that the emergency stop on pendant can´t reset duet3, is that whyle the config etc. is saved on the pi ?

      posted in CNC
      madedi123undefined
      madedi123
    • RE: CNC Pendant Disconnecting Duet

      Aux(bad-csum): G91 G0 F6000 X10.0<LF>Aux(bad-csum): G91 G0 F6000 X-10.0<LF>Aux(bad-csum): G91 G0 F6000 X10.0<LF>Aux(bad-csum): G91 G0 F6000 X-10.0<LF>Aux(bad-csum): G91 G0 F6000 X0.1<LF>Aux(bad-csum): G91 G0 F6000 X-0.1<LF>Aux(bad-csum): G91 G0 F6000 Y0.1<LF>Aux(bad-csum): G91 G0 F6000 Y-0.1<LF>Aux(bad-csum): G91 G0 F600 Z0.1<LF>Aux(bad-csum): G91 G0 F600 Z-0.1<LF>Aux(bad-csum): G91 G0 F600 Z0.1<LF>

      Looks like the Duet3 and reprap get the commands from the ardiono correct, but why is there no movement ? and what is (bad-csum) after the command ?

      posted in CNC
      madedi123undefined
      madedi123
    • RE: CNC Pendant Disconnecting Duet

      i will test it tomorrow, yes i know that the emergency stop works but nothing else.

      posted in CNC
      madedi123undefined
      madedi123
    • RE: ESP8266 NeoPixel Driver

      Hello

      My problem is that my pendant (the same as david's, with an arduino micro) only sends the M112 command, but does not perform any movement via the encoder. My hardware is a DUET3 6HC with SBC and without Panel DUE, Configuration CNC. The arduino sketch was uploaded with firmware 1.8.1 thank you for your help

      posted in Accessories and Add-ons
      madedi123undefined
      madedi123
    • RE: CNC Pendant Disconnecting Duet

      Hello

      My problem is that my pendant (the same as david's, with an arduino micro) only sends the M112 command, but does not perform any movement via the encoder. My hardware is a DUET3 6HC with SBC and without Panel DUE, Configuration CNC. The arduino sketch was uploaded with firmware 1.8.1 thank you for your help

      posted in CNC
      madedi123undefined
      madedi123
    • RE: PENDANT ONLY SEND THE M112

      do you know if i have to configure something in davids ino file from github ?

      posted in Duet Hardware and wiring
      madedi123undefined
      madedi123
    • RE: PENDANT ONLY SEND THE M112

      i can read it on dwc console, but nothing when i turn the encoder?

      posted in Duet Hardware and wiring
      madedi123undefined
      madedi123