Posts made by MandalaRose

Well, it hasn't done it since I replaced the hotend and the probe. I think the probe was shorting out and causing a pause maybe.

I'll monitor and post more info if it happens again.

Wade

On my oldest duet printer, I've suddenly had a problem with it "hanging" at around 13%, typically somewhere in layer 6. Seems to be mostly on larger prints. I will check the printer, and it's hung there, with the "pause" active. Nothing will restart the printer. Only thing I can do is reset the machine and let it cool down and restart my print.

e3dv6 hotend
orbiter 2.0 extruder
custom probe using z limit switch inputs (been using this for years with no problems)

Board: Duet WiFi 1.02 or later + DueX5
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 2.05.1 (2020-02-09b1)
Duet WiFi Server Version: 1.23

I know there is 3.x, but this has been bulletproof and I'm not motivated to update to 3x.

Below is the M112 report.

Thanks,
Wade

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-9T6BU-FG3S0-7J9FJ-3S06S-K843F
Used output buffers: 1 of 24 (10 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93760 of which 304 recycled
Exception stack ram used: 432
Never used ram: 10864
Tasks: NETWORK(ready,676) HEAT(blocked,1232) DUEX(suspended,160) MAIN(running,3800) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:11:43 ago, cause: software
Last software reset time unknown, reason: User, spinning module GCodes, available RAM 10976 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 8
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 31.8, current 32.6, max 33.3
Supply voltage: min 24.1, current 24.2, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/207
Driver 1: standstill, SG min/max 0/198
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max 8/275
Driver 6: standstill, SG min/max 52/310
Driver 7: standstill, SG min/max 13/285
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2023-12-03 09:45:35
Cache data hit count 2033717545
Slowest loop: 4.31ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 41, FreeDm: 160, MinFreeDm: 156, MaxWait: 10015ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 16, completed moves: 16, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 3 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.44ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.23
  WiFi MAC address 84:f3:eb:42:b0:46
  WiFi Vcc 3.38, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 24208
  WiFi IP address 10.0.0.191
  WiFi signal strength -54dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0
  === Filament sensors ===
  Extruder 0 sensor: ok

@Phaedrux said in Help entering new wifi password:

; Add default wifi network;M291 R"Add default WIFI network? Y/N" P"This will add duetwifi access point." S3 T10 M552 S0 ; Disable network moduleG4 S5 ; wait 5 secondsM587 S"NETWORKNAME" P"PASSWORD" ; Add duet wifi SSID to remembered networks listG4 S5 ; wait 5 secondsM552 S1 ; reenable wifi module M291 R"duetwifi SSID added." P"Check console to verify IP address."

That worked! Thanks!!!

Yeah, macro didn't work, and neither did the global. Guess it's YAT. Just a pain as the usb is a bit hard to get to on this printer.

Wade

My business moved to a new location, and I am unable to completely enter the new wifi password using the Panel Due 7. I literally cannot enter the last double quotes. That's it.

For example: M587 S"xxxxxxxxxxx" P"##################

The panel literaly won't let me enter the double quotes affter the password.

How else can I get a new wifi setup for my printer?

And no, I can't change my ssid or password, I have literally every other system setup on it already and some are quite hard to change.

Wade

@rjenkinsgb Hm, we live out in the country, so there's no other wifi nearby. I don't believe I have a lot of 2.4 devices, but thanks, I'll look at my router settings tonight.

When I first turn it on, and connect my browser to it, it pops up, but after several minutes, I get the "connection lost" window. The duet itself seems to be still connected. I'm 1 room away from my router, maybe 15 feet. It's also a brand new router from my cable company, which is xfinity.

If I just leave it sit, the interface screen pops up, then after a few minutes it goes away. This is how I have to currently use my printer, with interrupted wifi. It's really frustrating.

I should also mention that I have 4 different printers all running a duet2 and they all do this same thing. Below is my various versions.

Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later + DueX5
Firmware Version: 2.02(RTOS) (2018-12-24b1)
WiFi Server Version: 1.21
Web Interface Version: 1.22.6

Any help would be appreciated.

Wade

@dc42 Not yet. I am very new to duet, and the printer is working really good. I'm hesitant to perform the upgrade unless I know I won't have to re-setup all my configurations for my printer.

I also need to figure out how to perform the firmware upgrade.

In my startup, I am using the following codes:

G29 S1; turn on mesh bed leveling from the data saved on the sd card
M376 H5; turn on fade feature so it fades after 5mm height

I am using the following software versions:

• Firmware Electronics: Duet Wifi 1.02 or later + DueX5
• FirmwareVersion: 2.0(RTOS) (2018-06-05b3
• WiFi Server Version: 1.21
• Web Interface Version: 1.21.1

My problem is that when I have the M376 H5 in the gcode file, mesh leveling doesn't activate. If I take the M376 out, it works fine. Can anyone give me some ideas to try in order to fix this?

Thanks,
Wade