Posts made by mauriciomartins

Hello guys, as I already said in my case the problem is that the 3HC card is not accepting the current settings of the motors, I believe that my config.g has the M906 configured correctly.

I have to check with M112 the status of the voltages as @Phaedrux is suggesting. All of my power wiring is 14 gauge.
Unfortunately only next Monday I will be able to do more tests but I will be following this topic carefully because I realized that I am not alone with this problem.
Thank you all for the support!

@fcwilt yah, weird behaviour...
Let's try to bring @dc42 to this topic to help us understanding it

@fcwilt Thanks for you feedback!
Could you try what @deckingman is suggesting, sending just M906 without parameters to check the motors currents?
Thanks!

@deckingman Could you please share your config.g?
Thanks!

@deckingman because it's clear that there's no torque.
I'm using the same type of nema23 in all axis, the 4 Z motors are connected to the 6HC and I can set the current and it's working,
X and Y not, if I replace it with a nema17 just for debugging it works ,but without a strong torque.

I'm not using 1XD I'm using 3HC with 3 integrated drivers...

@fcwilt Thanks for your reply!
How to set the current in the 3HC itself not using M906?

Hey!
This is my first topic and I hope to get my problem fixed

I don't know why but my Duet3 3HC is not accepting the stepper motors currents settings... Maybe it's a mistake in the config.g

Do not be alarmed by the size of the printer, it will be really giant ... as soon as I have permission I will publish some photos

Thanks in advance!

Here is the config.g

; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Thu Mar 04 2021 11:26:14 GMT+0000 (Western European Standard Time)

; General preferences
G90                                           ; send absolute coordinates...
M83  

M550 P"io_BIG"                               ; set printer name

; Drives
M569 P1.0 S1                                 ; physical drive 1.0 goes forwards | X Front Stepper
M569 P1.1 S0                                 ; physical drive 1.1 goes forwards | X Back Stepper
M569 P1.2 S0                                 ; physical drive 1.1 goes forwards | Y stepper

M569 P0.0 S0                                 ; physical drive 0.0 goes forwards | Front Left Z
M569 P0.1 S0                                 ; physical drive 0.1 goes forwards | Front Right Z
M569 P0.2 S0                                 ; physical drive 0.2 goes forwards | Back Left Z
M569 P0.3 S0                                 ; physical drive 0.3 goes forwards | Back Right Z

M569 P121.0 S1                               ; physical drive 121.0 goes forwards | Front Right Z

M584 X1.0:1.1 Y1.2 Z0.0:0.1:0.2:0.3 E121.0   ; set drive mapping

M350 X16 Y16 Z16 E16 I1                       ; configure microstepping with interpolation
M92 X53.33 Y53.33 Z200.00 E420.00             ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00           ; set maximum instantaneous speed changes (mm/min)
M203 X5000.00 Y5000.00 Z1500.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00           ; set accelerations (mm/s^2)
M906 X2200 Y2200 Z2200 E1350 I30               ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                       ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                              ; set axis minima
M208 X1920 Y1240 Z1000 S0                     ; set axis maxima

; Endstops
M574 X1 S1 P"!1.i01.in"                        ; configure active-high endstop for low end on X via pin 1.io1.in
M574 Y1 S1 P"!1.io1.in"                        ; configure active-high endstop for low end on Y via pin 1.io3.in
M574 Z1 S1 P"!io2.in"                          ; configure active-high endstop for low end on Z via pin io0.in

; Z-Probe
M558 P0 H5 F120 T60000                        ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                      ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138  ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                            ; create bed heater output on out0 and map it to sensor 0
M307 H0 B1 S1.00                              ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                       ; map heated bed to heater 0
M143 H0 S120                                  ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1                            ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00                              ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                  ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"121.out1" Q500                     ; create fan 0 on pin 121.out1 and set its frequency
M106 P0 S0 H-1                               ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"121.out2" Q500                     ; create fan 1 on pin 121.out2 and set its frequency
M106 P1 S1 H1 T45                            ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                              ; define tool 0
G10 P0 X0 Y0 Z0                               ; set tool 0 axis offsets
G10 P0 R0 S0                                  ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600                             ; enable support for PanelDue