Posts made by Mythbear74

@soare0 are you not able to see the video?

All right, I finally found a way to send A video. https://discord.gg/G3X9ha9B

Is there a way I can send you guys a video of the print issue?

@droftarts thank you I will try that

@soare0 yes but do you have a way of actually achieving the erase of the height map/G29

Honestly at this point I’d rather like to know how to completely eradicate the height map system so it forgets about it.
PS, I am not from china I am in the US and I am quite new to this

All right, so I tried both those inputs, but it did the same problem. Is there any more information you need?

No I’m not from China. It’s just this thing is actually a gift to me and I can just got thrown it after they set it up. I will try putting in that code and then give you an update. thanks

Heres the others

; config-override.g file generated in response to M500 at 2024-02-19 18:43
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 R2.000 C140.000:140.000 D65.00 S1.00 V0.0 B0 I0
M307 H1 R3.192 C111.500:105.000 D6.72 S1.00 V24.0 B0 I0
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v3.1.10+4-LPC on Tue Jan 19 2021 17:25:01 GMT+0800 (中国标准时间)
M561 ; clear any bed transform
G29  ; probe the bed and enable compensation

I don't have a mesh.g

Here is my config.g it was having trouble sending the file

; Configuration file for SKR-E3-RRF (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.10+4-LPC on Tue Jan 19 2021 17:25:01 GMT+0800 (中国标准时间)

; General preferences
M950 P1 C"SP"
M42 P1 S1

G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 PAsa3DPrinter                         ; set printer name

; Network
M552 S-1
M552 S0
M587 S"namllok" P"7856501514"
M552 S1
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S0                                     ; physical drive 0 goes forwards using default driver timings
M569 P1 S0                                     ; physical drive 1 goes forwards using default driver timings
M569 P2 S1                                     ; physical drive 2 goes forwards using default driver timings
M569 P3 S0                                     ; physical drive 3 goes forwards using default driver timings
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E93.00               ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00            ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z600.00 E1200.00      ; set maximum speeds (mm/min)
M201 X600.00 Y600.00 Z20.00 E350.00            ; set accelerations (mm/s^2)
M906 X700 Y700 Z650 E750 I30                   ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X230 Y230 Z250 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
;M574 Z1 S1 P"zstop"                            ; configure active-high endstop for low end on Z via pin zstop
;M591 D0 P7 C"e0stop" S1  R50:130 L7.0 E10

; Z-Probe
M950 S0 C"Servo0"                               ; create servo pin 0 for BLTouch
M558 P9 C"^probe" H5 F800 T20000                ; set Z probe type to bltouch and the dive height + speeds
M557 X10:180 Y10:180 R-1 P2:2                      ; define mesh grid   
G31 P500 X-40 Y10 Z4.3                           ; set Z probe trigger value, offset and trigger height 

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bed" T0                              ; create bed heater output on bed and map it to sensor 0
M307 B1 S1.00                                  ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S150                                   ; set temperature limit for heater 0 to 150C
M143 H0 S150                                   ; set temperature limit for heater 0 to 150C
M308 S1 P"e0temp" Y"thermistor" T100000 B3950  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 R3.192 C111.5:105.0 D6.72 S1.00 V24.0                           ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S260                                                  ; set temperature limit for heater 1 to 300C

; Fans
M950 F0 C"fan0" Q400                          ; create fan 0 on pin fan0 and set its frequency
;M106 P0 S0 H1 T0                                ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q400                          ; create fan 1 on pin fan1 and set its frequency
M106 P1 S0 H1 T60                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                               ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
;M575 P1 S1 B57600                              ; enable support for PanelDue
;M575 P1 S2 B57600

M552 S1; enable network
M150 X2

T0 P0
G29 S1
M501

So do you want me to send the code again but in this other way

Yeah, like I said before I’m new and this is like my first time using the thing also, I don’t know how to find this tab when signing into this account

Here it is

@Mythbear74 https://drive.google.com/drive/folders/1mVh4PYC3evAnAbOAZaH302QmmA_yATmp?usp=sharing

All right, I’ll have in a bit

Oh ya I forgot more information

Ender three with bltouch using a btt skr2 mainboard I think running reprap, the only thing I’ve gone and changed is the M557

So I did what the guide said, but for some reason, the model keeps coming up as incredibly uneven and all it does is probe the four corners. I don’t know if it’s supposed to do that or it’s supposed to do the whole board.

All right, so I go I said my mesh comprehension to the right things and then I run the G 29 code but then when I go to look at the map it’s completely wrong because my bed is level

Hi I new
I got this printer from a friend of mine and when I go to make a new mesh G29 it starts in an area without anything under it