how can i solve this problem
Latest posts made by Nctogru
-
Slow tool change
Hello,
I am trying to run double extruder but transition between sets takes top long. I dont understand why it waits during transition. It changes the set almost in 10 seconds. -
Mini height sensor board
Hi. I bought the Mini height sensor board, but I have trouble setting the trigger height. The LEDs flash 4 times at first boot up and read the P1 value when the sensor is close to the table, but the head gets 3-4 mm high from the trays and I set it to be 1 mm between the card and the nozzle height what could be the problem?
-
RE: Short circuit
İs a short-circuit occasion effect PT100 board? Apart from that, I purchased ATTINY-25-205U Rohs piece but can't find any software for that. Could you help me about this situation?
-
RE: Short circuit
I would like to ask if we can connect wifi rc servo motor except 5 step motor
-
RE: Short circuit
hello, if you can give me the bom list of your height sensor I would like to change
-
RE: Short circuit
thank you davit i will order a new card as also the temperature sensor is burnt
PT100 temperature sensors
Messages Error: Failed to initialise RTD: bad response from sensor
-
RE: Short circuit
Hello there. I bought new duet wifi and panel due. My previous card was burned due to short circuit. I installed a new mini height sensor board on my new card, checked the connections but the leds are dimly lit, so might it be burnt with the old card?
-
Wifi connection error
hello duet I can not connect to WiFi, network not found YAT terminal I use
M552 S2
ok<lf>WiFi reported error: invalid access point configuration<lf>Wifi module is idle <lf>M552 S2
ok<lf>WiFi reported error: invalid access point configuration<lf>Wifi module is idle<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g…Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S1
Trying to connect at 230400 baud: success<lf>Erasing 4096 bytes...<lf>Erasing 233472 bytes...<lf>Uploading file...<lf>5% complete<lf>10% complete<lf>15% complete<lf>20% complete<lf>25% complete<lf>30% complete<lf>35% complete<lf>40% complete<lf>45% complete<lf>50% complete<lf>55% complete<lf>60% complete<lf>65% complete<lf>70% complete<lf>75% complete<lf>80% complete<lf>85% complete<lf>90% complete<lf>95% complete<lf>Upload successful<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M552 S1
ok<lf>WiFi reported error: no known networks found<lf>Wifi module is idle <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M122
=== Diagnostics ===<lf>Used output buffers: 1 of 32 (5 max)<lf>=== Platform ===<lf>RepRapFirmware for Duet WiFi version 1.20 running on Duet WiFi 1.0<lf>Board ID: 08DGM-9568A-F23SD-6J9DL-3SJ6K-K9RHH<lf>Static ram used: 15448<lf>Dynamic ram used: 99256<lf>Recycled dynamic ram: 4080<lf>Stack ram used: 3576 current, 4460 maximum<lf>Never used ram: 7828<lf>Last reset 00:02:39 ago, cause: power up<lf>Last software reset time unknown, reason: User, spinning module GCodes, available RAM 3752 bytes (slot 1)<lf>Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff<lf>Error status: 0<lf>Free file entries: 10<lf>SD card 0 detected, interface speed: 20.0MBytes/sec<lf>SD card longest block write time: 0.0ms<lf>MCU temperature: min 26.1, current 28.7, max 29.0<lf>Supply voltage: min 1.2, current 1.3, max 1.3, under voltage events: 0, over voltage events: 0<lf>Driver 0: ok, SG min/max not available<lf>Driver 1: ok, SG min/max not available<lf>Driver 2: ok, SG min/max not available<lf>Driver 3: ok, SG min/max no <warning: maximal="" number="" of="" bytes="" per="" line="" exceeded!="" check="" the="" end-of-line="" settings="" or="" increase="" limit="" in="" advanced="" terminal="" settings.="">M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M997 S1
Trying to connect at 230400 baud: success<lf>Erasing 4096 bytes...<lf>Erasing 180224 bytes...<lf>Uploading file...<lf>5% complete<lf>10% complete<lf>15% complete<lf>20% complete<lf>25% complete<lf>30% complete<lf>35% complete<lf>40% complete<lf>45% complete<lf>50% complete<lf>55% complete<lf>60% complete<lf>65% complete<lf>70% complete<lf>75% complete<lf>80% complete<lf>85% complete<lf>90% complete<lf>95% complete<lf>Upload successful<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M587
M587: Failed to retrieve network list<lf>ok <lf>M587
M587: Failed to retrieve network list<lf>ok <lf>M115
FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.20 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2017-12-23<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M997 S1
Trying to connect at 230400 baud: success<lf>Erasing 4096 bytes...<lf>Erasing 180224 bytes...<lf>Uploading file...<lf>5% complete<lf>10% complete<lf>15% complete<lf>20% complete<lf>25% complete<lf>30% complete<lf>35% complete<lf>40% complete<lf>45% complete<lf>50% complete<lf>55% complete<lf>60% complete<lf>65% complete<lf>70% complete<lf>75% complete<lf>80% complete<lf>85% complete<lf>90% complete<lf>95% complete<lf>Upload successful<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M552
WiFi module is idle<lf>ok <lf>M552 S0
ok <lf>M552 S0
ok <lf>M552 S0
ok <lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok <lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok <lf><lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok <lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M552
WiFi module is idle<lf>ok <lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok <lf>; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sun Dec 31 2017 14:08:46 GMT+0300 (Türkiye Standart Saati); General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P5 ; Set firmware compatibility to look like Repetier
; Automatic saving after power loss is not enabledM667 S1 ; Select CoreXY mode
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X250 Y250 Z250 S0 ; Set axis maxima; Endstops
M574 X1 Y2 S1 ; Set active low endstops
M574 Z1 S2 ; Set endstops controlled by probe
M558 P1 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:235 Y15:235 S20 ; Define mesh grid; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M350 X256 Y256 Z32 E16:16 I0 ; Configure microstepping without interpolation
M92 X2560 Y2560 Z3200 E96.96185885:96.96185885 ; Set steps per mm
M566 X900 Y900 Z12 E120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 E1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 E250:250 ; Set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E2000:2000 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X200 ; Set thermistor + ADC parameters for heater 1 and remap it to channel 201
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
M305 P2 X201 ; Set thermistor + ADC parameters for heater 2 and remap it to channel 202
M143 H2 S280; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X11.5 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H ; Define tool 1
G10 P1 X11.5 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C; Network
M550 Pnt ; Set machine name
M551 P123456789 ; Set password
M552 S1 ; Enable network
M587 S"7605" P"Magmasoft69" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet; Fans
;M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
;M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
;M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned onM106 P0 S1 I0 F500 H1 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on; Custom settings are not configured</lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></warning:></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf>
-
RE: Short circuit
Hello,
On the head part, we have a card to which we plug flex cable. If we add a protection on it, can we avoid these kind of accidents? Do heat and sensors work well?