Posts made by Nctogru

how can i solve this problem

Hello,
I am trying to run double extruder but transition between sets takes top long. I dont understand why it waits during transition. It changes the set almost in 10 seconds.

Hi. I bought the Mini height sensor board, but I have trouble setting the trigger height. The LEDs flash 4 times at first boot up and read the P1 value when the sensor is close to the table, but the head gets 3-4 mm high from the trays and I set it to be 1 mm between the card and the nozzle height what could be the problem?

İs a short-circuit occasion effect PT100 board? Apart from that, I purchased ATTINY-25-205U Rohs piece but can't find any software for that. Could you help me about this situation?

I would like to ask if we can connect wifi rc servo motor except 5 step motor

hello, if you can give me the bom list of your height sensor I would like to change

thank you davit i will order a new card as also the temperature sensor is burnt

PT100 temperature sensors

Messages Error: Failed to initialise RTD: bad response from sensor

Hello there. I bought new duet wifi and panel due. My previous card was burned due to short circuit. I installed a new mini height sensor board on my new card, checked the connections but the leds are dimly lit, so might it be burnt with the old card?

hello duet I can not connect to WiFi, network not found YAT terminal I use

M552 S2
ok<lf>WiFi reported error: invalid access point configuration<lf>Wifi module is idle <lf>M552 S2
ok<lf>WiFi reported error: invalid access point configuration<lf>Wifi module is idle<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g…Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S0:1:2
M997: File DuetWebControl.bin not found<lf>ok <lf>M997 S1
Trying to connect at 230400 baud: success<lf>Erasing 4096 bytes...<lf>Erasing 233472 bytes...<lf>Uploading file...<lf>5% complete<lf>10% complete<lf>15% complete<lf>20% complete<lf>25% complete<lf>30% complete<lf>35% complete<lf>40% complete<lf>45% complete<lf>50% complete<lf>55% complete<lf>60% complete<lf>65% complete<lf>70% complete<lf>75% complete<lf>80% complete<lf>85% complete<lf>90% complete<lf>95% complete<lf>Upload successful<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M552 S1
ok<lf>WiFi reported error: no known networks found<lf>Wifi module is idle <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M122
=== Diagnostics ===<lf>Used output buffers: 1 of 32 (5 max)<lf>=== Platform ===<lf>RepRapFirmware for Duet WiFi version 1.20 running on Duet WiFi 1.0<lf>Board ID: 08DGM-9568A-F23SD-6J9DL-3SJ6K-K9RHH<lf>Static ram used: 15448<lf>Dynamic ram used: 99256<lf>Recycled dynamic ram: 4080<lf>Stack ram used: 3576 current, 4460 maximum<lf>Never used ram: 7828<lf>Last reset 00:02:39 ago, cause: power up<lf>Last software reset time unknown, reason: User, spinning module GCodes, available RAM 3752 bytes (slot 1)<lf>Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff<lf>Error status: 0<lf>Free file entries: 10<lf>SD card 0 detected, interface speed: 20.0MBytes/sec<lf>SD card longest block write time: 0.0ms<lf>MCU temperature: min 26.1, current 28.7, max 29.0<lf>Supply voltage: min 1.2, current 1.3, max 1.3, under voltage events: 0, over voltage events: 0<lf>Driver 0: ok, SG min/max not available<lf>Driver 1: ok, SG min/max not available<lf>Driver 2: ok, SG min/max not available<lf>Driver 3: ok, SG min/max no <warning: maximal="" number="" of="" bytes="" per="" line="" exceeded!="" check="" the="" end-of-line="" settings="" or="" increase="" limit="" in="" advanced="" terminal="" settings.="">M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M587
No remembered networks<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok <lf>M588 S "7605"
M588: Bad or missing parameter<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M997 S1
Trying to connect at 230400 baud: success<lf>Erasing 4096 bytes...<lf>Erasing 180224 bytes...<lf>Uploading file...<lf>5% complete<lf>10% complete<lf>15% complete<lf>20% complete<lf>25% complete<lf>30% complete<lf>35% complete<lf>40% complete<lf>45% complete<lf>50% complete<lf>55% complete<lf>60% complete<lf>65% complete<lf>70% complete<lf>75% complete<lf>80% complete<lf>85% complete<lf>90% complete<lf>95% complete<lf>Upload successful<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M587
M587: Failed to retrieve network list<lf>ok <lf>M587
M587: Failed to retrieve network list<lf>ok <lf>M115
FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.20 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2017-12-23<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M997 S1
Trying to connect at 230400 baud: success<lf>Erasing 4096 bytes...<lf>Erasing 180224 bytes...<lf>Uploading file...<lf>5% complete<lf>10% complete<lf>15% complete<lf>20% complete<lf>25% complete<lf>30% complete<lf>35% complete<lf>40% complete<lf>45% complete<lf>50% complete<lf>55% complete<lf>60% complete<lf>65% complete<lf>70% complete<lf>75% complete<lf>80% complete<lf>85% complete<lf>90% complete<lf>95% complete<lf>Upload successful<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M552
WiFi module is idle<lf>ok <lf>M552 S0
ok <lf>M552 S0
ok <lf>M552 S0
ok <lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok <lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok <lf><lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok <lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok<lf>RepRapFirmware for Duet WiFi Version 1.20 dated 2017-12-23<lf><lf>Executing config.g...Error: Attempt to emulate unsupported firmware.<lf>Kinematics is CoreXY with axis factors X:1.000 Y:1.000 Z:1.000<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: Failed to initialise RTD: bad response from sensor<lf>Error: M587:
M552
WiFi module is idle<lf>ok <lf>M587 S "7605" P "Magmasoft69"
M587: Bad or missing parameter<lf>ok <lf>; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sun Dec 31 2017 14:08:46 GMT+0300 (Türkiye Standart Saati)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P5 ; Set firmware compatibility to look like Repetier
; Automatic saving after power loss is not enabled

M667 S1 ; Select CoreXY mode
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X250 Y250 Z250 S0 ; Set axis maxima

; Endstops
M574 X1 Y2 S1 ; Set active low endstops
M574 Z1 S2 ; Set endstops controlled by probe
M558 P1 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:235 Y15:235 S20 ; Define mesh grid

; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M350 X256 Y256 Z32 E16:16 I0 ; Configure microstepping without interpolation
M92 X2560 Y2560 Z3200 E96.96185885:96.96185885 ; Set steps per mm
M566 X900 Y900 Z12 E120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z180 E1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 E250:250 ; Set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E2000:2000 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X200 ; Set thermistor + ADC parameters for heater 1 and remap it to channel 201
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
M305 P2 X201 ; Set thermistor + ADC parameters for heater 2 and remap it to channel 202
M143 H2 S280

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X11.5 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H ; Define tool 1
G10 P1 X11.5 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C

; Network
M550 Pnt ; Set machine name
M551 P123456789 ; Set password
M552 S1 ; Enable network
M587 S"7605" P"Magmasoft69" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Fans
;M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
;M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
;M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

M106 P0 S1 I0 F500 H1 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Custom settings are not configured</lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></warning:></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf></lf>

Hello,
On the head part, we have a card to which we plug flex cable. If we add a protection on it, can we avoid these kind of accidents? Do heat and sensors work well?

I guess the heater and mini height sensor contacted each other. When I plug it to usb, U1 starts heat up right away. Also, when I plug Panel Duo to pc via usb, U1 on panel stars heating. There is no visual. I might have burnt it all. Both duet wifi and panel duo were destroyed.

hello duet I made a short circuit on the wifi card. short circuit possibilities are fans, heaters, temperature sensors, mini z height sensor card. When i plug the card into usb only only 2 leds are lit and the computer can not detect it is there a possibility of repair?

[22:33, 15.1.2018] Yasin Kizilay: Hello there. In the RepRapFirmware Configuration Tool, in the Microstepping Values section, which step I choose in the Values section, the Steps per mm value always remains at 420, the old machine has the marlin software. I was writing the result into the related section according to the formula I gave above, I choose 16x on microstepping values section and engine angle is 1.8 degrees and the engine is directly connected without a gearbox. The extruder gear is mk8 and the diameter is 11 mm. Which values do I need to enter on the RepRapFirmware Configuration Tool page. Please help me. I am about to go mad.

I got perfect results by using 110.584 on smooth surfaces. But i will try your values too. By the way step engines overheat although max current is 2 ampers and although i run them 1,5 ampers. What causes this overheat. The brand of the Engines are moons.

extruder thread diameter is 11mm and it is running stepper motor directly. There is no gear box in between and I found the "set steps per mm" value using the formula below and wrote it in the config file. How did you calculate the value you wrote? Also my driver type is bowden. Can you briefly write me the logic of calculation?

e_steps_per_mm = (motor_steps_per_rev * driver_microstep) * (hob_effective_diameter * pi)

(200 * 16)=3200
3200* (11 * 3.14159) = 110.584

Hello. I choose the microstep 16 and I use 16x200=3600 formula and thread diameter is 11 mm. 11x3,14159=34,55749. I multiply this result by 3600 and write the result (110,534)to config file but although the flament needs to be 5 mm, it is 5.5mm.

Yes David. Home all and bed problems have been solved. Thank you very much. But the engines connected to e1 and e2 drivers do not work. I checked the engines and the cables but there were no problems. Is there something wrong with the config file?

; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sun Dec 31 2017 14:08:46 GMT+0300 (Türkiye Standart Saati)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P5 ; Set firmware compatibility to look like Repetier
; Automatic saving after power loss is not enabled

M667 S1 ; Select CoreXY mode
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X250 Y250 Z250 S0 ; Set axis maxima

; Endstops
M574 X1 Y2 S1 ; Set active low endstops
M574 Z1 S2 ; Set endstops controlled by probe
M558 P1 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:235 Y15:235 S20 ; Define mesh grid

; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes forwards
M569 P4 S0 ; Drive 4 goes forwards
M350 X256 Y256 Z256 E256:256 I0 ; Configure microstepping without interpolation
M350 Z32 I1 ; Configure microstepping with interpolation
M92 X2560 Y2560 Z3200 E92.6462:92.6462; Set steps per mm
M566 X900 Y900 Z12 E120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z2500 E1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 E250:250 ; Set accelerations (mm/s^2)
M906 X1600 Y1600 Z1000 E2000:2000 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X200 ; Set thermistor + ADC parameters for heater 1 and remap it to channel 201
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
M305 P2 X201 ; Set thermistor + ADC parameters for heater 2 and remap it to channel 202
M143 H2 S280

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X11.5 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H ; Define tool 1
G10 P1 X11.5 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C

; Network
M550 Pnanovol ; Set machine name
M551 P123456789 ; Set password
M552 S1 ; Enable network
M587 S"nt" P"nt" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Fans
;M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
;M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
;M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

M106 P0 S1 I0 F500 H1 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Custom settings are not configured

https://s14.postimg.org/txghc73e9/20180110_193722.jpg
https://s14.postimg.org/ua7vie13l/END_STOP.jpg
https://s14.postimg.org/b54m8mept/HOME_POINT_1.jpg

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool on Wed Jan 10 2018 18:30:22 GMT+0300 (Türkiye Standart Saati)
G91 ; relative positioning
G1 Z5 F6000 ; lift Z relative to current position
G1 S1 X-250 Y250 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 S1 X-250 ; home X axis
G1 S1 Y250 ; home Y axis
G1 X5 Y-5 F6000 ; go back a few mm
G1 S1 X-250 F1800 ; move slowly to X axis endstop once more (second pass)
G1 S1 Y-250 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X125 Y125 F1800 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed
;G1 Z5 F100 ; uncomment this line to lift the nozzle after homing

; Configuration file for Duet WiFi (firmware version 1.20 or newer)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sun Dec 31 2017 14:08:46 GMT+0300 (Türkiye Standart Saati)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates…
M83 ; ...but relative extruder moves
M555 P5 ; Set firmware compatibility to look like Repetier
; Automatic saving after power loss is not enabled

M667 S1 ; Select CoreXY mode
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X250 Y-250 Z250 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 S1 ; Set active low endstops
M574 Z1 S2 ; Set endstops controlled by probe
M558 P1 H5 F120 T6000 ; Set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height
M557 X15:235 Y15:235 S20 ; Define mesh grid

; Drives
M569 P0 S0 ; Drive 0 goes forwards
M569 P1 S0 ; Drive 1 goes forwards
M569 P2 S0 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M569 P4 S1 ; Drive 4 goes forwards
M350 X256 Y256 Z256 E256:256 I0 ; Configure microstepping without interpolation
M350 Z32 I1 ; Configure microstepping with interpolation
M92 X2560 Y2560 Z3200 E420:420 ; Set steps per mm
M566 X900 Y900 Z12 E120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z1200 E1200:1200 ; Set maximum speeds (mm/min)
M201 X500 Y500 Z250 E250:250 ; Set accelerations (mm/s^2)
M906 X1500 Y1500 Z1500 E2000:2000 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Heaters
M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X200 ; Set thermistor + ADC parameters for heater 1 and remap it to channel 201
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
M305 P2 X201 ; Set thermistor + ADC parameters for heater 2 and remap it to channel 202
M143 H2 S280

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 ; Define tool 1
G10 P1 X0 Y0 Z0 ; Set tool 1 axis offsets
G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C

; Network
M550 Pnanovol ; Set machine name
M551 P123456789 ; Set password
M552 S1 ; Enable network
M587 S"nt" P"nt" ; Configure access point. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Custom settings are not configured

; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool on Sun Dec 31 2017 13:20:17 GMT+0300 (Türkiye Standart Saati)
M561 ; clear any bed transform
; Probe the bed at 4 points
G30 P0 X15 Y15 H0 Z-99999
G30 P1 X15 Y50 H0 Z-99999
G30 P2 X50 Y50 H0 Z-99999
G30 P3 X50 Y15 H0 Z-99999 S

hi I sent the files you requested
Thank you