Ok not sure what the error was but it seems to work now. I formated the SD and unpacked the files from the Git into it. Then I installed the update to 3.1.1 again an uploaded a fresh firmware from the fw generator. No idea what went wrong before.

Yes I did. (FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-05-19b2)

Nop the fuse is fine. Just checked. In case if it's blown shouldn't the steppers also not work?

Hi, I just finished wiring up my printer and wanted to test the heaters. Bed works but due to any reason I can't get the hotend heater to work. I already tried a second one, changed from e0 to e1, measured if there is a break in the wiring ( about 15 Ohm so it should fit the 40W rating) and checked the thermistor that works as well.

I'm using this one from trianglelab: https://de.aliexpress.com/item/32815934251.html?spm=a2g0o.store_home.productList_1322398741.pic_0

(don't mind the whole code. I scraped the old config.g and uploaded a new one. Didn't do any other changes yet)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"My Printer" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M569 P4 S1 ; physical drive 4 goes forwards
M584 X0 Y1 Z2:3 E4 ; set drive mapping
M350 X16 Y16 Z16:16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00:800.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z12.00:12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00:180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00:20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800:800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X370 Y370 Z400 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M558 P5 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P200 X0 Y0 Z0 ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e1heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
T0 ; select first tool

So I checked the SDcard and the reprap.htm file was missing.

Thanks for your replies. I'll check the SD tomorrow. Was just wondering because I used the DWC1 GUI on a different Duet Wifi and RRP3.1.1 prior without an issue. My webcontroll is V3.1.1.. Just finished wiring the board and will check if there are any other issues.

Hi,
I just got a new Duet Wifi and updated to V3.1.1.
(FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-05-19b2).
DWC2 works fine but when I try to access DWC1 I only get this message: Your Duet rejected the HTTP request: page not found
Check that the SD card is mounted and has the correct files in its /www folder.

Any ideas how I can fix that/ what could cause this error?

I mostly use Inventor and Nastran in-CAD.

Just checked the motor coils and wires. No short

Unfortunately I'm using E1 -.-
The motor is sitting on a printed holder so not connected to anything that could cause a shortcircuit. But good idea to check the coils before I'm blowing another driver X,D