Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. okercho
    3. Topics
    • Profile
    • Following 0
    • Followers 0
    • Topics 7
    • Posts 117
    • Best 1
    • Controversial 0
    • Groups 0

    Topics created by okercho

    • okerchoundefined

      Mesh bed Levelling with BLTouch. Am I doing something wrong?

      Tuning and tweaking
      • • • okercho
      28
      0
      Votes
      28
      Posts
      5.8k
      Views

      habitotiundefined

      Hi,
      while this is an older thread, the problem itself is very current, unfortunately 😞
      While I had it for an Anycubic Mega S printer, it was basically the same root cause. I solved it w/o having to replace any hardware, but with some additional mathematics to compensate for the rod twist. I wrote something up explaining the issue and also provide there a little online tool to create appropriate compensation GCode commands. This works great for me and I have no more issues with the bent hardware, so maybe it is a proper resolution for some of you also... 😊

      Regards, habitoti

    • okerchoundefined

      Questions about Bed Levelling with multiple Z Motors

      Tuning and tweaking
      • • • okercho
      2
      0
      Votes
      2
      Posts
      599
      Views

      dc42undefined

      I suggest that for the moment you leave out the G29. Run G32 and see what it says the deviation is before and after (after should always be zero if you have only 2 probe points). Then run it 2 or 3 more times and see what deviation it reports after each one. Depending on your mechanics, it may take a few runs to converge.

      There is an extra M671 parameter in firmware 1.21RC3 to help with convergence.

    • okerchoundefined

      Question about Stall Detection

      Tuning and tweaking
      • • • okercho
      7
      0
      Votes
      7
      Posts
      1.3k
      Views

      okerchoundefined

      @dc42:

      1. You can use F0 for homing and F1 for stall detection, if that helps.

      2. Have you tried using S2 but either decreasing allowed acceleration (and maybe jerk) or increasing the H parameter in M915?

      Will try both and report back, thanks πŸ™‚

    • okerchoundefined

      Frozen + Restart + WiFi Errors

      General Discussion
      • • • okercho
      5
      0
      Votes
      5
      Posts
      862
      Views

      okerchoundefined

      Testing wifi so far…

      Restarted duet 10 times, 5 worked, 5 failed (50% of the time...).

      Interestingly, 1 fails, 1 works, always doing more or less the same (turn on, wait until connects or fails, wait ~20s, turn off, wait ~10s, turn on...). At least, works more often than before...

      I moved back to 1.19.2 (both, firmware and wifi), and repeated the testing 6 times: 100% connection success

      It shows "Connected", then "Wifi Module Started" (this is not shown in 1.20), then "Wifi Module connected to Access point" (ping start answering), then 5 seconds after this, ping start to fail, and screen shows "Error retrieving wifi status message" and then connects again with "Wifi Module connected to access point" and don't fail anymore. After the third reboot, "Error retrieving wifi status message" didn't show again, and wifi works perfectly fine.

      Moved to 1.21RC1 and again, one works, one fails... so I don't think this is hw related :S

      Can I give you anything else for diagnostics?

      Regards

    • okerchoundefined

      Question about Z Height

      General Discussion
      • • • okercho
      3
      0
      Votes
      3
      Posts
      535
      Views

      okerchoundefined

      Uhm, I will check today again, but I think that Z head position was reporting 0.22 before I applied the BabySteps.

      Thanks!

    • okerchoundefined

      Question about IR Sensor and Buildtak

      Tuning and tweaking
      • • • okercho
      36
      0
      Votes
      36
      Posts
      4.6k
      Views

      IdefixRCundefined

      Has anyone experience with the IR sensor and black color PEI sheet?
      Like this: https://www.amazon.de/gp/aw/d/B06XHK217S/ref=mp_s_a_1_1?__mk_de_DE=Γ…MΓ…ZÕÑ&qid=1500030592&sr=8-1Ο€=AC_SX236_SY340_FMwebp_QL65&keywords=pei+3d+druck&dpPl=1&dpID=31cdHAayG4L&ref=plSrch

      Thanks

    • okerchoundefined

      Duet Wifi Stock and Revision Question

      Order discussion
      • • • okercho
      4
      0
      Votes
      4
      Posts
      814
      Views

      T3P3Tonyundefined

      We have a limited number back in stock now with more due next week.