Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. oldironjunkie
    • Profile
    • Following 0
    • Followers 0
    • Topics 3
    • Posts 25
    • Best 1
    • Controversial 0
    • Groups 0

    oldironjunkie

    @oldironjunkie

    1
    Reputation
    1
    Profile views
    25
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    oldironjunkie Unfollow Follow

    Best posts made by oldironjunkie

    • RE: biqu H2 V2S REVO not working

      I did some checking. I got a working motor and new cable. The wiring to the motor was correct. I double and tripple checked. I remapped the extruder motor to drive 4, heated up the hot end and manually extruded (without actually extruding just running a motor) and it worked fine. I remaped the same setup to drive 3 (original E0 driver) and the new moto did not work and I got the same warning for a short to ground. So I do have a bad driver for EO on the card. I then Checked the BIQU motor. I have readings directly form the motor. one coil is 2.7ohm and the other is .7ohm. So iI do also have a bad motor. Probably what fried the driver on the Duet. So off to search for anew motor. Looks like the gear on the motor is pressed on and accordingto everything I have found not available. It a NEMA 14 motor but all have a plain shaft. So I will contact Biqu to see if one is available. So I do appreciate the help. It pointed me in the right direction.

      posted in Duet Hardware and wiring
      oldironjunkieundefined
      oldironjunkie

    Latest posts made by oldironjunkie

    • RE: error after upgrading firmware

      @droftarts Still on 3.5.2. About to start some long prints . We will see if it works in a few days. Again I thanks you. John.

      posted in Duet Hardware and wiring
      oldironjunkieundefined
      oldironjunkie
    • RE: error after upgrading firmware

      @droftarts Thanks for your help I did all you asked and kept having the same issue. I reloaded the firmware and it is now working ok. No messages. It must have been something in the install process that caused it.

      posted in Duet Hardware and wiring
      oldironjunkieundefined
      oldironjunkie
    • RE: error after upgrading firmware

      @droftarts I forgot to sayt hat the config.g and config-override.g were changed when I had issues with the motor driver last year.

      posted in Duet Hardware and wiring
      oldironjunkieundefined
      oldironjunkie
    • RE: error after upgrading firmware

      @droftarts I am in the middle of a print for the next 20 hours. Will try all when it is done.

      posted in Duet Hardware and wiring
      oldironjunkieundefined
      oldironjunkie
    • RE: error after upgrading firmware

      @droftarts Here is my config-override.g. looks like heater 2 is listed.

      M307 H2 R2.584 C226.4 D8.23 S.7 V24.3 ;TOOL HEAT updtaed 6/28/2023
      M572 D0 S.02 ;pressure advance
      M307 H0 R0.890 C200.2 D3.32 S1.00 V24.0 ;bed heat
      M106 P0 S.75 H-1 Q500

      posted in Duet Hardware and wiring
      oldironjunkieundefined
      oldironjunkie
    • RE: error after upgrading firmware

      I just copied and pasted the config.g file. hope this helps.

      ;General preferences
      M575 P1 S1 B57600 ; enable support for PanelDue
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"OLDIRON PRINTER" ; set printer name

      ;Network
      M552 S1 ; enable network
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S0 ; disable Telnet

      ;Drives
      M569 P0 S0 ; physical drive 0 goes backwards
      M569 P1 S1 ; physical drive 1 goes forwards
      M569 P2 S0 ; physical drive 2 goes backwards
      M569 P3 S0 ; physical drive 3 goes backwards
      ;M569 P4 S0 ; physical drive 4 goes backwards TITAN AERO
      M569 P4 S1 ; physical drive 4 goes forwards SLICE MOSQUITO
      ;M569 P3 S0 ; physical drive 3 goes backwards
      ;M569 P3 S0 ; physical drive 3 goes backwards
      ;M569 P3 S0 ; physical drive 3 goes backwards
      ;M569 P3 S0 ; physical drive 3 goes backwards
      M584 X0 Y1 Z2 E4:4:4:4 ; set drive mapping
      M350 X16 Y16 Z16 E16:16:16:16 I1 ; configure microstepping with interpolation
      ;M92 X80.70 Y79.95 Z399.74 E408 ;set steps per mm E3D titan aero extruder
      M92 X80.70 Y79.95 Z399.74 E405 ; set steps per mm mosquito extruder (recheck)
      ;M92 X80.70 Y79.95 Z399.74 E454. ; set steps per mm biqu extruder
      M566 X800.00 Y800.00 Z800.00 E650:800:800:800 ; set maximum instantaneous speed changes (mm/min)
      M203 X7500.00 Y7500.00 Z6500.00 E900:900:900:900 ; set maximum speeds (mm/min)
      M201 X800.00 Y800.00 Z500.00 E250:300:300:300 ; set accelerations (mm/s^2)
      M906 X1400 Y1800 Z900 E1200:800:800:800 I50 ; set motor currents (mA) and motor idle factor in per cent
      M84 S300 ; Set idle timeout

      ;Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X315 Y310 Z400 S0 ; set axis maxima3

      ;Endstops
      M574 X1 S1 P"!xstop" ; configure active-(high) LOW endstop for low end on X via pin xstop
      M574 Y1 S1 P"!ystop" ; configure active-(high) LOW endstop for low end on Y via pin ystop
      M574 Z1 S1 P"!zstop" ; configure active-(high) LOW endstop for low end on Z via pin zstop

      ;Z-Probe
      M950 S0 C"duex.pwm1" ; Duet 2 WiFi/Ethernet + DueX2/5
      M558 P9 C"^zprobe.in" H3 F50 T9000 R0.5 ; Duet 2 WiFi/Ethernet, DueX2/55
      G31 X-5 Y-25 Z3.66 ; z probe offset
      M557 X0:300 Y10:300 S30 ; bed mesh size and spacing
      M376 H9 ;bed mesh fading

      ;Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 B0 S1.0 ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
      M950 H2 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M307 H2 R2.584 C226.4 D8.23 S.5 V24.3 ;tool heat
      M143 H2 S350 ; set temperature limit for heater 1 to 350C

      ;Fans
      M950 F0 C"fan0" ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S.75 H-1 Q500 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S.75 H-1 Q500 ; set fan 1 value. Thermostatic control is turned on

      ;Tools
      M563 P1 D1 H2 F0 ; define tool 1
      M572 D1 S0.02 ;ADDED PRESSURE ADVANCE SETTING
      G10 P1 R0 S0

      ; Miscellaneous
      M501 ; load saved parameters from non-volatile memory
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
      T1 ; select first tool

      posted in Duet Hardware and wiring
      oldironjunkieundefined
      oldironjunkie
    • error after upgrading firmware

      I recently upgraded my firmware to 3.5.2 and after doing so I started to get a warning message "Error in start-up file macro line 2: Heater 1 not found" a start up. In the past I had issues with an extruder driver that was burned out by a faulty motor. I had to switch to extruder 1 and also heater 2 and was working for an extended period of time. Till the firmware upgrade. Not sure where to look for the start up file macro (unable to find). I am sure if I am pointed in the right direction I will fix it. Also tried uploading the config.g file but it is not working. Probably not doing it right. Printer is working ok but the message is annoying. Please help.

      posted in Duet Hardware and wiring
      oldironjunkieundefined
      oldironjunkie
    • RE: BL TOUCH NOT WORKING.

      @droftarts I will add the G90 and change the pressure advance setting to the correct tool. The reason I am not using the 0 drive is that ithe driver was fried by my bad extruder motor. I had to switch drives once I got the motor replaced. Thanks for all the help

      posted in IR Height Sensor
      oldironjunkieundefined
      oldironjunkie
    • RE: BL TOUCH NOT WORKING.

      @droftarts I finally got it working. I had a bad factor BL touch harness to begin with (I have a replacement coming). Before I found out that I messed with everything and got everything out of wack. I should have followed instructions and approached things logically. I now have a bed level height file, homing works great including the Z axis and my first and second prints came out great. I still have to mess with pressure advance (I just installed a new extruder) and dial in the Z height. Thanks to all that helped I really appreciate that. As for the final files here they are.

      ;General preferences
      M575 P1 S1 B57600                                               ; enable support for PanelDue
      G90                                                             ; send absolute coordinates...
      M83                                                             ; ...but relative extruder moves
      M550 P"OLDIRON PRINTER"                                         ; set printer name
      
      ;Network
      M552 S1                                                         ; enable network
      M586 P0 S1                                                      ; enable HTTP
      M586 P1 S0                                                      ; disable FTP
      M586 P2 S0                                                      ; disable Telnet
      
      ;Drives
      M569 P0 S0                                                       ; physical drive 0 goes backwards
      M569 P1 S1                                                       ; physical drive 1 goes forwards
      M569 P2 S0                                                       ; physical drive 2 goes backwards
      M569 P3 S0                                                       ; physical drive 3 goes backwards
      M569 P4 S1													     ; physical drive 4 goes forwards
      ;M569 P3 S0                                                      ; physical drive 3 goes backwards
      ;M569 P3 S0                                                      ; physical drive 3 goes backwards
      ;M569 P3 S0                                                      ; physical drive 3 goes backwards
      ;M569 P3 S0                                                      ; physical drive 3 goes backwards
      M584 X0 Y1 Z2 E4:4:4:4                                           ; set drive mapping    
      M350 X16 Y16 Z16 E8:8:8:8 I1                                     ; configure microstepping with interpolation
      M92 X79.68 Y79.44 Z400.00 E820.0:454.00:454.00:454.00             ; set steps per mm
      M566 X900.00 Y900.00 Z900.00 E1600.00:1600.00:1600.00:1600.00    ; set maximum instantaneous speed changes (mm/min)
      M203 X4000.00 Y4000.00 Z1500.00 E4000.00:4000.00:4000.00:4000.00 ;set maximum speeds (mm/min) 
      M201 X1000.00 Y1000.00 Z350.00 E600.00:600.00:600.00:600.00      ; set accelerations (mm/s^2) 
      M906 X1000 Y1000 Z1000 E800:800:800:800 I50                      ; set motor currents (mA) and motor idle factor in per cent 
      M84 S300                                                         ; Set idle timeout
      
      
      
      ;Axis Limits
      M208 X5 Y5 Z0 S1                                                ; set axis minima
      M208 X320 Y300 Z400 S0                                          ; set axis maxima
      
      ;Endstops
      M574 X1 S1 P"!xstop"                                             ; configure active-(high) LOW endstop for low end on X via pin xstop
      M574 Y1 S1 P"!ystop"                                             ; configure active-(high) LOW endstop for low end on Y via pin ystop
      M574 Z1 S1 P"!zstop"                                             ; configure active-(high) LOW endstop for low end on Z via pin zstop
      
      ;Z-Probe
      M950 S0 C"duex.pwm1"                                            ; Duet 2 WiFi/Ethernet + DueX2/5
      M558 P9 C"^zprobe.in" H3 F100 T9000 R0.5						; Duet 2 WiFi/Ethernet, DueX2/5
      G31 X0 Y-40 Z.6 P25												;probe offsets, trigger height and trigger value
      M557 X1:320 Y1:250 S30                                        ;define mesh grid
      
      ;Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138                  ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0                                           ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 B0 S1.00                                                ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0                                                         ; map heated bed to heater 0
      M143 H0 S120                                                    ; set temperature limit for heater 0 to 120C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4138                   ; configure sensor 1 as thermistor on pin e0temp
      M950 H2 C"e0heat" T1                                            ; create nozzle heater output on e0heat and map it to sensor 1      
      M307 H2 R2.584 C226.4 D8.23 S.5 V24.3							;tool heat 
      M143 H2 S350                                                    ; set temperature limit for heater 1 to 350C    
      
      ;Fans
      M950 F0 C"fan0"                                                 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S.75 H-1 Q500                                           ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500                                            ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S.75 H-1 Q500                                           ; set fan 1 value. Thermostatic control is turned on
      
      
      
      ;Tools
      M563 P1 D1 H2 F0                           			 			; define tool 1  
      M572 D0 S0.004									                ;ADDED PRESSURE ADVANCE SETTING	
      G10 P1 R0 S0
      
      ; Miscellaneous
      M501                                                            ; load saved parameters from non-volatile memory
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"              ; set voltage thresholds and actions to run on power loss
      T1                                                              ; select first tool
      
      ; deployprobe.g
      M280 P0 S10 				;code for deploying the Z probe
      
      ; retractprobe.g
      M280 P0 S90     			;code for retracting the Z probe
      
      ; homeall.g
      ; called to home all axes
      ;
      ; generated by RepRapFirmware Configuration Tool v3.3.3 on Wed Sep 29 2021 16:53:30 GMT-0500 (Central Daylight Time)
      G91                     ; relative positioning
      G1 H2 Z5 F6000          ; lift Z relative to current position
      G1 H1 X-302 Y-302 F6000 ; move quickly to X and Y axis endstops and stop there (first pass)
      G1 H2 X5 Y5 F6000       ; go back a few mm
      G1 H1 X-302 Y-302 F180  ; move slowly to X and Y axis endstops once more (second pass)
      G1 X150 Y150 F5000
      G30 
      ; Uncomment the following lines to lift Z after probing
      ;G91                    ; relative positioning
      ;G1 Z5 F100             ; lift Z relative to current position
      ;G90                    ; absolute positioning
      
      ; homez.g
      ; called to home the Z axis
      M98 P"homeall.g"                             ; Call the home X & Y macro to home those axes first
      M98 P"deployprobe.g"                         ; Called to extend the BL-Touch probe pin to allow probing to take place
      G30                                          ; Home the Z axis by probing the bed
      M98 P"retractprobe.g"
      
      posted in IR Height Sensor
      oldironjunkieundefined
      oldironjunkie
    • RE: BL TOUCH NOT WORKING.

      @oliof I was using those names beacause that is what I was sent by a friend of mine. It has changes since. I will post the final files once it is done, working and tested. I am in the process of doing that now but unfortunatly life just gets in the way.

      posted in IR Height Sensor
      oldironjunkieundefined
      oldironjunkie