Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. oogway
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 20
    • Best 0
    • Controversial 0
    • Groups 0

    oogway

    @oogway

    0
    Reputation
    1
    Profile views
    20
    Posts
    0
    Followers
    0
    Following
    Joined Last Online
    Location Rochester, New York

    oogway Unfollow Follow

    Latest posts made by oogway

    • RE: Odd prints with super jagged edges

      Calibrating the extruder was the missing step, thanks for save dc42!

      posted in Tuning and tweaking
      oogwayundefined
      oogway
    • RE: Odd prints with super jagged edges

      I have not, i must have missed that step during the initial setup. I'll calibrate it and report back the results.

      posted in Tuning and tweaking
      oogwayundefined
      oogway
    • Odd prints with super jagged edges

      Hey all,

      These are my first prints and they are coming out super jagged. I've tried messing with different extruder speeds but it doesn't change much. My Delta moves super quick when printing. Not sure if that is the cause… anyways. The prints are below. What does it look like to you?

      Here is my config file if that helps.

      Configuration file for T3P3 Kossel XL with Duet WiFi: https://postimg.org/gallery/2gl47q47k/

      And the pictures of my prints. https://postimg.org/gallery/3c054p24m/

      posted in Tuning and tweaking
      oogwayundefined
      oogway
    • RE: Short circuit error on Kossel XL with duet wifi

      Just to confirm, it was my thermistor. I replaced it and it heated up immediately. Thanks for the help everyone!

      posted in Duet Hardware and wiring
      oogwayundefined
      oogway
    • RE: Short circuit error on Kossel XL with duet wifi

      @T3P3Tony:

      The Hotend PCB is on Github here:

      https://github.com/T3P3/KosselHotendBoard

      It certainly sounds like a new thermistor is the most likely.

      Awesome, I'll start there. Should i replace both wires coming out of my hotend? or just the thicker red one?

      posted in Duet Hardware and wiring
      oogwayundefined
      oogway
    • RE: Short circuit error on Kossel XL with duet wifi

      Does anyone know where i can find the hotend pcb? I tried looking on the E3D website and the Think3dprint3d website but did not see it.

      Was also wondering this…since my hotend pcb still powers on my 2 fans connected to it...is it safe to assume that it's ok? I'm now thinking it's just the thermistor that needs to be replaced..

      posted in Duet Hardware and wiring
      oogwayundefined
      oogway
    • RE: Short circuit error on Kossel XL with duet wifi

      So i measured the pictured black and green wires and got a resistance of .010 when the mm is set to 2M. Hope that's normal.

      https://postimg.org/image/qfql2u489/

      I measured the resistance of the thermistor plug (link to picture in a previous post) and got the same .0l reading.

      Thanks for all of your help so far everyone. I'm a total noob. lol

      posted in Duet Hardware and wiring
      oogwayundefined
      oogway
    • RE: Short circuit error on Kossel XL with duet wifi

      @T3P3Tony:

      Sounds like you have a faulty thermistor or faulty wires between the board and the thermistor on your hotend.

      Ok I'll look into replacing the thermistor. Is it possible I blew that little board that sits above the hotend? The one i plug everything into.

      posted in Duet Hardware and wiring
      oogwayundefined
      oogway
    • RE: Short circuit error on Kossel XL with duet wifi

      I ended up stripping the wires just to be sure. Still same error message.

      posted in Duet Hardware and wiring
      oogwayundefined
      oogway
    • RE: Short circuit error on Kossel XL with duet wifi

      @dc42:

      You could put wires in the connector holes and measure between those.

      I put wires into the holes as far back as i could and measured but still get a reading of .0L. Perhaps i'm measuring it incorrectly? I used speaker wire and made sure to stick them in as far as they would go.

      posted in Duet Hardware and wiring
      oogwayundefined
      oogway