Posts made by paul12

@DC42 Please respond.

hello,
Is it not possible to resume print after power failure when the files are in the Card 1 on the Paneldue.i was getting Error M23: Gcode file "1:/name.gcode" not found Error M24: cannot print because no file is selected!
Resume print works fine while using online with duet 2 wifi onboard SD card.

Duet 2 wifi on V 2.02(RTOS) (2018-12-24b1)
Paneldue on V1.23.2

hello,
Is it not possible to resume print after power failure when the files are in the Card 1 on the Paneldue.i was getting Error M23: Gcode file "1:/name.gcode" not found Error M24: cannot print because no file is selected!
Resume print works fine while using online with duet 2 wifi onboard SD card.

Duet 2 wifi on V 2.02(RTOS) (2018-12-24b1)
Paneldue on V1.23.2

does Firmware Version: 2.02(RTOS) (2018-12-24b1) has the fix? It doesnt seem to work for me.

@DC42 sir this feature is still not available?

anyone using cura for delta printers? Or please do recommend any other slicer for delta printers compatible with Duet ( Other than slic3r )

@phaedrux WOWWW!!! adding the interpolation just made the printer SUPER silent.

But still there is under extrusion

@burtoogle i will try increasing the micro steps like @Phaedrux suggested.

@naqaj i had made it to 1.75 while making the custom machine profile on latest version. let me confirm it again. Thank you

@phaedrux am on the latest version released 2.02(RTOS) (2018-12-24b1).
Increasing the micro steps will solve my issue sir?

@burtoogle thank you for the quick reply sir.

0_1547068635101_CFFFP_Avengers_logo_keychain.gcode

i have a custom delta printer with duet 2 wifi, i usually use slic3r, but when i started using cura on my ender 3, the top surface finish was better. so when i tried using cura with delta the extrusion was at a very very low rate, i have turned on " relative extrusion" on cura.

Should i make any other changes to the cura or duet settings?

Also which slicer will everyone recommend?

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sat Nov 03 2018 14:41:59 GMT+0800 (China Standard Time)

; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware compatibility to look like RepRapFirmare

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R258 L397.110 B150 H330 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 PSPARX3D ; Set machine name
M552 S1 ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; Apply custom drive mapping
M350 X16 Y16 Z16 E16 I0 ; Configure microstepping without interpolation
M92 X80 Y80 Z80 E100.7200 ; Set steps per mm
M566 X1000 Y1000 Z1000 E1000 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E1200 ; Set maximum speeds (mm/min)
M201 X3000 Y3000 Z3000 E1500 ; Set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z-0.1 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S0 ; Set active low endstops

; Z-Probe
M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 H10 F108 T3600 ; Set Z probe type to bltouch and the dive height + speeds
G31 P25 X0 Y13 Z2.481 ; Set Z probe trigger value, offset and trigger height
M557 R140 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4388 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H0 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
T0 ; Select first tool
M501

@alexlin how to disable it?

i have a custom delta printer with duet 2 wifi, i usually use slic3r, but when i started using cura on my ender 3, the top surface finish was better. so when i tried using cura with delta the extrusion was at a very very low rate, i have turned on " relative extrusion" on cura.

Should i make any other changes to the cura of duet settings?

@dc42 am facing the same issue, will try this method and inform the result

anyone please do help me. what should i do to correct the error?

So, can i revert to a previous version of the firmware to rectify the problem?

I will change the deploy n retract setting in the bed.g.

Also sir when will the firmware 2.02RC4 be available?

I have set up a new delta printer, but while printing a large object the print does not stick to the build plate.

I have tried changing the H parameter in the Bed.g , but it does not seem to have any effect on the auto calibration.

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Sat Nov 03 2018 14:41:59 GMT+0800 (China Standard Time)

; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware compatibility to look like RepRapFirmare

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R258 L451.5 B150 H433 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 PSPARX3D ; Set machine name
M552 S1 ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes backwards
M584 X0 Y1 Z4 E3 ; Apply custom drive mapping
M350 X16 Y16 Z16 E16 I0 ; Configure microstepping without interpolation
M92 X80 Y80 Z80 E94.792 ; Set steps per mm
M566 X1200 Y1200 Z1200 E1200 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E1200 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1000 ; Set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 Z-0.1 S1 ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S0 ; Set active low endstops

; Z-Probe
M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 H10 F108 T3600 ; Set Z probe type to bltouch and the dive height + speeds
G31 P25 X0 Y13 Z3.09 ; Set Z probe trigger value, offset and trigger height
M557 R140 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4388 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H0 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
T0 ; Select first tool
M501

Bed.g

; bed.g
; called to perform automatic delta calibration via G32
;http://escher3d.com/pages/wizards/wizardbed.php
; generated by RepRapFirmware Configuration Tool on Sat Nov 03 2018 14:41:58 GMT+0800 (China Standard Time)
M561 ; clear any bed transform
G28 ; home all towers
M98 Pdeployprobe.g ; deploy mechanical Z probe
; Probe the bed at 10 peripheral and 6 halfway points, and perform 6-factor auto compensation
; Before running this, you should have set up your Z-probe trigger height to suit your build, in the G31 command in config.g.
G30 P0 X0.00 Y140.00 Z-99999 H0.38
G30 P1 X89.99 Y107.25 Z-99999 H0.38
G30 P2 X137.87 Y24.31 Z-99999 H0.34
G30 P3 X115.52 Y-66.70 Z-99999 H0
G30 P4 X44.02 Y-120.95 Z-99999 H-0.21
G30 P5 X-44.02 Y-120.95 Z-99999 H-0.21
G30 P6 X-115.52 Y-66.70 Z-99999 H0
G30 P7 X-137.87 Y24.31 Z-99999 H0
G30 P8 X-89.99 Y107.25 Z-99999 H0
G30 P9 X0.00 Y70.00 Z-99999 H0
G30 P10 X60.62 Y35.00 Z-99999 H0
G30 P11 X54.88 Y-31.68 Z-99999 H0
G30 P12 X0.00 Y-59.04 Z-99999 H0
G30 P13 X-54.88 Y-31.68 Z-99999 H0
G30 P14 X-60.62 Y35.00 Z-99999 H0
G30 P15 X0 Y0 Z-99999 S6
; Use S-1 for measurements only, without calculations. Use S4 for endstop heights and Z-height only. Use S6 for full 6 factors
; If your Z probe has significantly different trigger heights depending on XY position, adjust the H parameters in the G30 commands accordingly. The value of each H parameter should be (trigger height at that XY position) - (trigger height at centre of bed)
M98 Pretractprobe.g ; retract mechanical Z probe

Some point stick perfectly while some wont, i tried giving very larde values for H , but no change is happening after auto calibration.

No, i have not enabled debugging, there is no M111 command in my config.

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Fri Oct 05 2018 00:31:02 GMT+0530 (India Standard Time)

; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware compatibility to look like RepRapFirmare

;*** The homed height is deliberately set too high in the following - you will adjust it during calibration.
M665 R258 L398 B140 H377 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 PSPARX3D ; Set machine name
M552 S1 ; Enable network
;*** Access point is configured manually via M587
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; Drive 3 goes forwards
M584 X0 Y1 Z4 E3 ; Apply custom drive mapping
M350 X16 Y16 Z16 E16 I0 ; Configure microstepping without interpolation
M92 X80 Y80 Z80 E100.48 ; Set steps per mm
M566 X1200 Y1200 Z1200 E1200 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z18000 E1200 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1000 ; Set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Endstops
M574 X2 Y2 Z2 S0 ; Set active low endstops

; Z-Probe
M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 H10 F120 T3600 ; Set Z probe type to bltouch and the dive height + speeds
G31 P25 X-23 Y9 Z1.244 ; Set Z probe trigger value, offset and trigger height
M557 R140 S20 ; Define mesh grid

; Heaters
M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4388 C0 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S1 I0 F500 H0 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured

; Miscellaneous
T0 ; Select first tool
M501

I think the problem is with repetier host, when i first make a connection with YAT , there is no debugging messages after when i connect it to repetier the debugging starts and restarting the YAT connection the debugging messages are continued until M111 S0 command is given.