Sorted it and dancing around the workshop .
Looked at all the frequency settings on VFD and noticed that PD011 was set to 200.00. Set it to factory 0 and it all works.
Thanks so much for all your help. This forum is invaluable.

@chrishamm Yep that sorted it. Thanks for your help.

I have just updated the firmware and DWC on my duet 3 board but I cannot see a touch probe window on the dashboard as in the previous version.
My probe settings are:
; Probe configuration executed by config.g
M558 P5 C"!io0.in" H5 F500 T500 ; Set Z probe and use IO0.in inverted
;G31 P500 X10 Y10 Z4.766 ; set current probe status
;M557 X15:215 Y15:195 S20

I have the flat plate the same as the ooznest probe which does XYZ and was controlled from the touch probe window on the Dashboard.
Can anyone help to sort this orlet me know how I can roll back the DWC version pease.

@chrishamm Yep that sorted it. Thanks for your help.

Hi,
I have a workbee 1010 with Duet 3 and RRF 3.3.
I have spindle control via the duet which starts and stops the spindle at beginning and end of job.
However if I PAUSE a job part way through, the spindle rises but does not stop, before waiting 10 seconds and then travelling to rear right of machine. I can however send M5 directly to switch it off from DWC so I know M5 works.
Any ideas?
TIA

PAUSE.g
; pause.g
; called when a print from SD card is paused
G90
G53 G1 Z{move.axes[2].max} F1500 ; move the Z-Axis to the maximum position
M5 ; turn off spindle
G4 S10 : wait for spindle to stop
G53 G1 X{move.axes[0].max} F2500 ; move the X-Axis to the maximum position
G53 G1 Y{move.axes[1].max} F2500 ; move the Y-Axis to the maximum position

RESUME.g
; resume.g
; called before a print from SD card is resumed

M3 R1 ;restore
G4 S10 ;wait for spindle to reach full speed
G1 H1 Z1500 F1500 ; raise the Z to the highest position
G1 R1 X0 Y0 ; go to directly above position of the last print move
G1 R1 X0 Y0 Z0 ; go back to the last print move

Sorted it and dancing around the workshop .
Looked at all the frequency settings on VFD and noticed that PD011 was set to 200.00. Set it to factory 0 and it all works.
Thanks so much for all your help. This forum is invaluable.

@jay_s_uk Still no joy. Set it to 6000 and M5 still wont make it stop. Tearing my hair out now as I cant get my head arround whats going on. Could it be a VFD setting?

@jay_s_uk Hi 1.5kw aircooled spindle

@jay_s_uk Minimum RPM on specs is 0 but have tried it at 600 but still the same.
If I adjust the 12000rpm it knocks the 24000rpm which is spot on, would it be an innacuracy with the 0-10v converter?

@jay_s_uk Minimum rpm is currently set to 0, should it be something else then?

Also just noticed that as I have to press STOP on the VFD to stop spindle I then can't restart using Web Control or Gcode.
Also when set at 12000rpm on web control it shows just over 13500rpm on VFD. Is this just a case of fine tuning the 0-10v converter?

@jay_s_uk So So close now. I now have spindle on and off and speed control via web control and gcode .
The only thing still not working is M5- Stop. When M5 is activated the spindle drops to about 500rpm, although VFD still shows 12000rpm, and stays there.
Is there a minimum RPM setting somewhere?
Thanks for your support so far you have been awesome!