• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login
  1. Home
  2. printthatthing
  3. Posts
  • Profile
  • Following 0
  • Followers 0
  • Topics 6
  • Posts 26
  • Best 1
  • Controversial 0
  • Groups 0

Posts made by printthatthing

  • RE: Overpowered heater

    @matt3o Thanks for the tip.

    posted in Tuning and tweaking
    undefined
    printthatthing
    24 Jan 2021, 09:07
  • RE: Overpowered heater

    @matt3o Thanks, I admit I forgot to search because I didn't expect it already existed. My bad, sorry.

    posted in Tuning and tweaking
    undefined
    printthatthing
    23 Jan 2021, 08:56
  • Overpowered heater

    Hi, is this something to worry about and can it be adjusted?
    duet.jpg

    posted in Tuning and tweaking
    undefined
    printthatthing
    23 Jan 2021, 08:36
  • RE: Expantion port logic output

    @dc42 said in Expantion port logic output:

    M950 P0 C"spi.cs5"

    Thank you, I got it to work now:)
    P5 was the next free so my config file now have these lines to start logic 0
    M950 P5 C"spi.cs5"
    M42 P5 S0

    My layer change script in Simplyfy3d as below.
    G1 X395 Y200 F15000
    G4 S0
    G4 P500
    M42 P5 S1
    G4 P200
    M42 P5 S0
    G4 P500

    posted in General Discussion
    undefined
    printthatthing
    29 Aug 2020, 06:08
  • RE: Expantion port logic output

    @bearer Thank you very much. I will try it once the ongoing prints are done.

    posted in General Discussion
    undefined
    printthatthing
    27 Aug 2020, 18:52
  • RE: Expantion port logic output

    @bearer Hi, I'm using Duet 2 WiFi with firmware 3.1.1

    posted in General Discussion
    undefined
    printthatthing
    27 Aug 2020, 18:47
  • Expantion port logic output

    Hi, how can I trigger CS5 pin or any availble pin?
    I have tried M42 CS5 S1 but it give me an error.
    I add a P in front M42 PCS5 S1 no error but the CS5 pin remains on 3V

    posted in General Discussion
    undefined
    printthatthing
    27 Aug 2020, 18:03
  • RE: Dual Z auto level

    @Phaedrux Works like a charm, thank you so much. I totally missed that line.

    posted in Tuning and tweaking
    undefined
    printthatthing
    12 Jul 2020, 18:39
  • RE: Dual Z auto level

    @Phaedrux No, thank you. I will check that.

    posted in Tuning and tweaking
    undefined
    printthatthing
    12 Jul 2020, 18:25
  • Dual Z auto level

    I'm not sure if I have understand it correct but I guess it's possible to adjust the Z-motors invidually after probing. After a sucessfull probing it should ajust the invidual Z motors I guess.
    Z is working with right Z-stepper connected to E1
    In config.g I have added M584 Z2:4 E3 to assign E1 to Z2
    Here is my bed.g

    G28
    G30 P0 X20 Y200 Z-99999
    G30 P1 X360 Y200 Z-99999 S2
    

    When I run G32 it starts probing at center, left and right side. (3 probes)
    It returns below error.
    Error: Probe points P0 to P1 must be in clockwise order starting near minimum X and Y
    Thank you

    posted in Tuning and tweaking
    undefined
    printthatthing
    12 Jul 2020, 18:19
  • RE: RRF Config Mapping

    @Phaedrux said in RRF Config Mapping:

    @printthatthing said in RRF Config Mapping:

    Update:
    My bad, it might be M303 H0 S90

    😑 Yes of course.

    Now it works fine:) Thank you so much for all support.

    posted in Tuning and tweaking
    undefined
    printthatthing
    10 Jul 2020, 22:05
  • RE: RRF Config Mapping

    @Phaedrux said in RRF Config Mapping:

    Executed M307 H0 S90 after the suggested changes.
    Error: M307: bad model parameters

    Update:
    My bad, it might be M303 H0 S90

    posted in Tuning and tweaking
    undefined
    printthatthing
    10 Jul 2020, 21:28
  • RE: RRF Config Mapping

    @Phaedrux i was missing M501 in config.g
    Restarted boad but getting same error when trying to heat bed.
    Tried to run M307 H0 S90 again but it fails with Error: M307: bad model parameters

    ; config-override.g file generated in response to M500 at 2020-07-10 23:02
    ; This is a system-generated file - do not edit
    ; Heater model parameters
    M307 H0 A340.0 C140.0 D5.5 S1.00 V0.0 B1
    M307 H1 A340.0 C140.0 D5.5 S1.00 V0.0 B0
    ; Workplace coordinates
    G10 L2 P1 X0.00 Y0.00 Z0.00
    G10 L2 P2 X0.00 Y0.00 Z0.00
    G10 L2 P3 X0.00 Y0.00 Z0.00
    G10 L2 P4 X0.00 Y0.00 Z0.00
    G10 L2 P5 X0.00 Y0.00 Z0.00
    G10 L2 P6 X0.00 Y0.00 Z0.00
    G10 L2 P7 X0.00 Y0.00 Z0.00
    G10 L2 P8 X0.00 Y0.00 Z0.00
    G10 L2 P9 X0.00 Y0.00 Z0.00
    
    posted in Tuning and tweaking
    undefined
    printthatthing
    10 Jul 2020, 21:08
  • RE: RRF Config Mapping

    @Phaedrux Ok, but I still not able to heat the bed. It start heating but halt after few seconds. Error: Heater 0 fault: temperature rising much more slowly than the expected 1.7°C/sec

    posted in Tuning and tweaking
    undefined
    printthatthing
    10 Jul 2020, 20:29
  • RE: RRF Config Mapping

    Now I'm stuck with error at bed heating.
    Error: Heater 0 fault: temperature rising much more slowly than the expected 1.7°C/sec
    Duet 2 Wifi power a solid state relay for a 220v heater.

    I executed M307 H0 S90
    M307 H0 results in below.
    Heater 0 model: gain 340.0, time constant 140.0, dead time 5.5, max PWM 1.00, calibration voltage 0.0, mode bang-bang

    Then I tried to save the value
    M307 H0 A340 C140 D5.5 V0 B0
    But it result in
    Warning: M307: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C

    posted in Tuning and tweaking
    undefined
    printthatthing
    10 Jul 2020, 20:07
  • RE: RRF Config Mapping

    @Phaedrux Ok thanks.

    posted in Tuning and tweaking
    undefined
    printthatthing
    10 Jul 2020, 19:57
  • RE: RRF Config Mapping

    @dc42 Aha, okay that make sense.

    posted in Tuning and tweaking
    undefined
    printthatthing
    9 Jul 2020, 10:52
  • RE: RRF Config Mapping

    Thank you all again. I think I have it running now.
    I had to keep ! for duex.pwm5 else it does not probe.
    config.g

    ; Configuration file for Duet WiFi (firmware version 3)
    ; executed by the firmware on start-up
    ;
    ; generated by RepRapFirmware Configuration Tool v3.1.3 on Wed Jul 08 2020 21:18:31 GMT+0200 (centraleuropeisk sommartid)
    
    ; General preferences
    G90                                            ; send absolute coordinates...
    M83                                            ; ...but relative extruder moves
    M550 P"Formbot Raptor 2"                       ; set printer name
    
    ; Network
    M552 S1                                        ; enable network
    M586 P0 S1                                     ; enable HTTP
    M586 P1 S0                                     ; disable FTP
    M586 P2 S0                                     ; disable Telnet
    
    ; Drives
    M569 P0 S1                                     ; physical drive 0 goes forwards
    M569 P1 S1                                     ; physical drive 1 goes forwards
    M569 P2 S1                                     ; physical drive 2 goes forwards
    M569 P3 S1                                     ; physical drive 3 goes forwards
    M584 X0 Y1 Z2 E3                               ; set drive mapping
    M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
    M92 X80.00 Y80.00 Z640.00 E415.00              ; set steps per mm
    M566 X900.00 Y900.00 Z12.00 E120.00            ; set maximum instantaneous speed changes (mm/min)
    M203 X6000.00 Y6000.00 Z180.00 E1200.00        ; set maximum speeds (mm/min)
    M201 X500.00 Y500.00 Z20.00 E250.00            ; set accelerations (mm/s^2)
    M906 X800 Y800 Z800 E800 I30                   ; set motor currents (mA) and motor idle factor in per cent
    M84 S30                                        ; Set idle timeout
    
    ; Axis Limits
    M208 X0 Y0 Z0 S1                               ; set axis minima
    M208 X400 Y400 Z350 S0                         ; set axis maxima
    
    ; Endstops
    M574 X1 S1 P"!xstop"                           ; configure active-high endstop for low end on X via pin !xstop
    M574 Y1 S1 P"!ystop"                           ; configure active-high endstop for low end on Y via pin !ystop
    M574 Z1 S2                                     ; configure Z-probe endstop for low end on Z
    
    
    ; Z-Probe
    M950 S0 C"!duex.pwm5"                           ; create servo pin 0 for BLTouch
    M558 P9 C"^zprobe.in" H5 F120 T6000            ; set Z probe type to bltouch and the dive height + speeds
    G31 P25 X-25 Y-5 Z0.489                          ; set Z probe trigger value, offset and trigger height
    M557 X5:380 Y5:380 S20                       ; define mesh grid
    
    ; Heaters
    M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
    M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
    M307 H0 B1 S1.00                               ; enable bang-bang mode for the bed heater and set PWM limit
    M140 H0                                        ; map heated bed to heater 0
    M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
    M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
    M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
    M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
    
    ; Fans
    M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
    M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
    M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
    M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on
    
    ; Tools
    M563 P0 D0 H1 F0                               ; define tool 0
    G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
    G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C
    
    ; Custom settings are not defined
    
    

    homeall.g

    ; homeall.g
    ; called to home all axes
    ;
    ; generated by RepRapFirmware Configuration Tool v3.1.3 on Wed Jul 08 2020 20:58:26 GMT+0200 (centraleuropeisk sommartid)
    G91                     ; relative positioning
    G1 H2 Z5 F6000          ; lift Z relative to current position
    G1 H1 X-405 Y-405 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
    G1 H2 X5 Y5 F6000       ; go back a few mm
    G1 H1 X-405 Y-405 F360  ; move slowly to X and Y axis endstops once more (second pass)
    
    
    G90                     ; absolute positioning
    G1 X150 Y150 F6000        ; move Z down stopping at the endstop
    G30                     ; home Z by probing the bed
    
    
    ; Uncomment the following lines to lift Z after probing
    G91                    ; relative positioning
    G1 Z5 F100             ; lift Z relative to current position
    G90                    ; absolute positioning
    

    Is the heatmap very bad or ok to use without adjustments?
    heat.png

    posted in Tuning and tweaking
    undefined
    printthatthing
    9 Jul 2020, 10:34
  • RE: RRF Config Mapping

    @JoergS5 I get it a try tomorrow. Thank you for all help.

    posted in Tuning and tweaking
    undefined
    printthatthing
    8 Jul 2020, 21:40
Unless otherwise noted, all forum content is licensed under CC-BY-SA