Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Rommie
    • Profile
    • Following 0
    • Followers 0
    • Topics 6
    • Posts 53
    • Best 0
    • Controversial 0
    • Groups 0

    Rommie

    @Rommie

    0
    Reputation
    1
    Profile views
    53
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Rommie Unfollow Follow

    Latest posts made by Rommie

    • RE: Where can i drill big holes in the smarteffector? dual-extruder

      Nope the 3 sensors are around the entire part, if your intention is to use the stress sensors for bed leaving there is no way, if not then drill anywhere

      posted in Smart effector for delta printers
      Rommieundefined
      Rommie
    • RE: Constant disconnects from DWC

      I'm on 1.20.1rc2 on firmware, 1.20+1 for wifi server and, 1.20 rc3 on dwc version. I have set macros up now so I can just use the panel due to reset the wifi turning off then on, I have been speaking to doug and he said to try rolling back to 1.20 on wifi server and try that. Will let ya know how it goes..

      There is also another chap on our discord channel that has had the same issues after upgrading his firmware from 1.19 to the 1.20+1 too

      posted in Firmware installation
      Rommieundefined
      Rommie
    • Constant disconnects from DWC

      I have upgraded all firmware to the newest yesterday, I am however now experiencing constant disconnects from the DWC, I have to then either close and reopen chrome to get it too connect again, or stop network on panel due direct and restart it with the m552 s0 and s1 respectively.

      not sure what's causing the issues

      posted in Firmware installation
      Rommieundefined
      Rommie
    • RE: T3P3 Kossel Mini R3 Wiring harness

      Me and Doug have both used 24awg cat 5e cable, we have double wired the cable to run the heater and it works perfect, only have 2 cables and the drive tube connected now and it's perfect

      posted in Smart effector for delta printers
      Rommieundefined
      Rommie
    • RE: Z probe issues

      Ok I must have overlooked the crimp as I though I had checked them all, seems it was a poor crimp on the 3.3 line, all fixed and working perfect

      posted in Smart effector for delta printers
      Rommieundefined
      Rommie
    • Z probe issues

      I have setup all the wires with no problems, these have been done to the pre production board, problem I have is that the duet board is giving out 3.3v but the effector is only showing 0.69 v as such I get no green led and probe stays at 1000 as if it is constant trigger, no idea what to do as everything else is working with no issues

      posted in Smart effector for delta printers
      Rommieundefined
      Rommie
    • RE: 6 Way Microfit connector

      Mine is already broken so would need a new housing to try it ??

      posted in Smart effector for delta printers
      Rommieundefined
      Rommie
    • RE: Place to show off PCB Effector assemblies

      4mm is perfect, just snug enough to hold it all in and then the nimble makes certain that it stays where it needs to be

      posted in Smart effector for delta printers
      Rommieundefined
      Rommie
    • RE: 6 Way Microfit connector

      I know it fouls badly as my 6way block on the effector now is missing the clip to hold the connector in, this is how we found the issue

      posted in Smart effector for delta printers
      Rommieundefined
      Rommie
    • RE: Duet3D PCB delta printer effector sneak preview

      Ahhh ok thanks

      posted in Smart effector for delta printers
      Rommieundefined
      Rommie