Posts made by Rommie

Nope the 3 sensors are around the entire part, if your intention is to use the stress sensors for bed leaving there is no way, if not then drill anywhere

I'm on 1.20.1rc2 on firmware, 1.20+1 for wifi server and, 1.20 rc3 on dwc version. I have set macros up now so I can just use the panel due to reset the wifi turning off then on, I have been speaking to doug and he said to try rolling back to 1.20 on wifi server and try that. Will let ya know how it goes..

There is also another chap on our discord channel that has had the same issues after upgrading his firmware from 1.19 to the 1.20+1 too

I have upgraded all firmware to the newest yesterday, I am however now experiencing constant disconnects from the DWC, I have to then either close and reopen chrome to get it too connect again, or stop network on panel due direct and restart it with the m552 s0 and s1 respectively.

not sure what's causing the issues

Me and Doug have both used 24awg cat 5e cable, we have double wired the cable to run the heater and it works perfect, only have 2 cables and the drive tube connected now and it's perfect

Ok I must have overlooked the crimp as I though I had checked them all, seems it was a poor crimp on the 3.3 line, all fixed and working perfect

I have setup all the wires with no problems, these have been done to the pre production board, problem I have is that the duet board is giving out 3.3v but the effector is only showing 0.69 v as such I get no green led and probe stays at 1000 as if it is constant trigger, no idea what to do as everything else is working with no issues

Mine is already broken so would need a new housing to try it ??

4mm is perfect, just snug enough to hold it all in and then the nimble makes certain that it stays where it needs to be

I know it fouls badly as my 6way block on the effector now is missing the clip to hold the connector in, this is how we found the issue

Ahhh ok thanks

@dc42:

All will be revealed when we start shipping.

Does it mean we will see them in stock today seeing as before we were told they will show on site when there available

I thought they were only going on the shop when ready, I can see the addons and can add to cart but still saying out of stock

@jannisj:

@Rommie:

Anymore updates as to when it's going on to the order pages, need to order a new pt100 sensor and daughtboard so will order all in one if it's not long out

As soon as it arrives in stock, they will put it on the page.
Hope it arrives soon myself, as I need "everything"
(Duet wifi, paneldue 5", pcb. hotend kit, ++)

-J

You will love the duet if you have never used one before, there fantastic and sooooo quiet, loudest thing I have is my beard air pump

Anymore updates as to when it's going on to the order pages, need to order a new pt100 sensor and daughtboard so will order all in one if it's not long out

It is done by an adapter Doug has made up, I'm sure he will either make you one or share the .stl if you ask him.

Ahhhh ok, I'll have to keep checking the store

Any news when it's going on the store David?

Yeah can't find where to order lol

@dc42:

@loic:

do you have an idea about the cost for a kit?
i will buy one for my delta xxl project +nimble

I think we will publish the prices tomorrow or Tuesday.

I will be buying one no matter what lol

@loic:

@dc42:

@loic:

i really love the design and the light weight
now it will be great to have piezo sensor available for this effector with nimble it could be a beast combo

The nozzle contact sensor is built in, so no need for a piezo. At least one of our beta testers is looking at mounting a Nimble on it.

thanks great
but does it will be better than a simple micro switch accuracy?
does it piezo or other way sensor?

From what I have seen of mesh bed comp between piezo and dc effector it wins hands down, I know doug has had experience with piezo and dc effector and he can't praise it enough. Getting to 0.002 dev on his tests