Best posts made by RonP

@jay_s_uk Thanks good catch, switched it. Looks like I need to redo the black 6 pin . Heading to bed. Thank you for taking the time to get me on the right path.

First i want to say thank you for everything.
It is working now.
Couple of suggestions:
1.) The ordering of the connections on the documentation (Smart Effector) doesn't line up with the actual 8 pin. Jay pointed out my error.
2.) Update the documentation to reflect the correct green led light or say it could be over here (empty header) or here (by the 8 pin)

So what i think happened is that we had it working shortly after the 6 pin re-do. I was so focused on the green led near the empty header that i didn't see the green led by the 8 pin.
I just happened to see it when i went to take it apart again and touched the print head and saw the green led by the 8 pin.

But thanks again for all the focus and attention.

@Phaedrux said in Help with setup:

indeed, i have done it twice some places even more.
But the step that i am stuck at is Commissioning step 4 the light never comes on .

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MS8-6JKFJ-3S86Q-TBGGN
Used output buffers: 3 of 24 (8 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 92584 of which 416 recycled
Exception stack ram used: 272
Never used ram: 12088
Tasks: NETWORK(ready,896) HEAT(blocked,1232) MAIN(running,3816) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:26:01 ago, cause: power up
Last software reset at 2021-01-10 18:59, reason: User, spinning module GCodes, available RAM 12000 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 33.3, current 42.2, max 42.6
Supply voltage: min 24.8, current 24.9, max 25.0, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-01-11 01:44:13
Cache data hit count 4294967295
Slowest loop: 2.11ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.66ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address dc:4f:22:6e:e4:db
WiFi Vcc 3.46, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25136
WiFi IP address 192.168.1.20
WiFi signal strength -46dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

Hello,
Let me thank you in advance.
I bought the he3d k280. I changed the main board to the duet 2 wifi v1.2 FW 2.5. I also purchased the duet smart effector v2. The challenge i am facing is I am unable to get the programable Z probe to work. I have read a lot of documentation trying to solve the issue.

Any insight or assistance would be greatly appreciated.
p.s. I will gladly supply any config or anything asked.

@jay_s_uk will be a couple of hours. Had to take dog to the vet.️