@jay_s_uk Thanks good catch, switched it. Looks like I need to redo the black 6 pin . Heading to bed. Thank you for taking the time to get me on the right path.

First i want to say thank you for everything.
It is working now.
Couple of suggestions:
1.) The ordering of the connections on the documentation (Smart Effector) doesn't line up with the actual 8 pin. Jay pointed out my error.
2.) Update the documentation to reflect the correct green led light or say it could be over here (empty header) or here (by the 8 pin)

So what i think happened is that we had it working shortly after the 6 pin re-do. I was so focused on the green led near the empty header that i didn't see the green led by the 8 pin.
I just happened to see it when i went to take it apart again and touched the print head and saw the green led by the 8 pin.

But thanks again for all the focus and attention.

@Phaedrux said in Help with setup:

indeed, i have done it twice some places even more.
But the step that i am stuck at is Commissioning step 4 the light never comes on .

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MS8-6JKFJ-3S86Q-TBGGN
Used output buffers: 3 of 24 (8 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 92584 of which 416 recycled
Exception stack ram used: 272
Never used ram: 12088
Tasks: NETWORK(ready,896) HEAT(blocked,1232) MAIN(running,3816) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:26:01 ago, cause: power up
Last software reset at 2021-01-10 18:59, reason: User, spinning module GCodes, available RAM 12000 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 33.3, current 42.2, max 42.6
Supply voltage: min 24.8, current 24.9, max 25.0, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-01-11 01:44:13
Cache data hit count 4294967295
Slowest loop: 2.11ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.66ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address dc:4f:22:6e:e4:db
WiFi Vcc 3.46, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25136
WiFi IP address 192.168.1.20
WiFi signal strength -46dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

Hello,
Let me thank you in advance.
I bought the he3d k280. I changed the main board to the duet 2 wifi v1.2 FW 2.5. I also purchased the duet smart effector v2. The challenge i am facing is I am unable to get the programable Z probe to work. I have read a lot of documentation trying to solve the issue.

Any insight or assistance would be greatly appreciated.
p.s. I will gladly supply any config or anything asked.

@jay_s_uk will be a couple of hours. Had to take dog to the vet.️

First i want to say thank you for everything.
It is working now.
Couple of suggestions:
1.) The ordering of the connections on the documentation (Smart Effector) doesn't line up with the actual 8 pin. Jay pointed out my error.
2.) Update the documentation to reflect the correct green led light or say it could be over here (empty header) or here (by the 8 pin)

So what i think happened is that we had it working shortly after the 6 pin re-do. I was so focused on the green led near the empty header that i didn't see the green led by the 8 pin.
I just happened to see it when i went to take it apart again and touched the print head and saw the green led by the 8 pin.

But thanks again for all the focus and attention.

@jay_s_uk hey Jay, went through it all again and it seems good. So does that mean my effector is bad ?
Thanks for taking the time to help me.

@jay_s_uk 24v

@jay_s_uk Here you go
config.g

config.g
Here it is

@jay_s_uk will be a couple of hours. Had to take dog to the vet.️

So everything has been redone.
Print lights are working, fans come on as expected, heater cartridge and thermistor work.
tried to power on using usb still no green light.

@jay_s_uk Thanks good catch, switched it. Looks like I need to redo the black 6 pin . Heading to bed. Thank you for taking the time to get me on the right path.

@jay_s_uk hey Jay, those are for the thermistor.
They were there and still didn't work.

Yep the print lights come on on the points.
Wiring is really messy rewired so please don't hold it against me
.