Posts made by rtuinila

Thanks for the reply!

I'm about to migrate from RRF2 to RRF3 and wanted to test all the utilities needed before I bricked my Duet2 Wifi. While Yat is able to connect through my usb cable, Bossa is not. When I select the com port my Duet2 is connected to I get a message back saying Bossa could not connect to the device. For informational purposes I did install the Duet driver for that com port before I tried any of this.
I've programmed a lot of devices in my career where some need the board to be in "reset" for the programmer to work and others don't. Is the Atmel on the board one of those that need to be in "reset"?

Thanks!

I would like one too!

@droftarts Hi Ian,

That is almost right. My probe is to the right of the nozzle but the bed would have to travel to Y29 before the probe would be over the bed.

I also just found out you don't see your comment edits till you reload the current page.

I just realized the 558 command in config.g. I never set the x and y offsets in that command. Could that be my problem?

Hi Phaedrux,

I found 2 M577 commands in my config.g file. An oversight by me and will be corrected but I would assume the last one in the config.g file would be the one that was used by G29. I also just noticed I probably should have set the x and y offsets in the M558 command. Anyway here is my config.g file

; Axis Limits
M208 X-41 Y-1 Z0 S1 ; set axis minima
M208 X250 Y227 Z210 S0 ; set axis maxima

; Endstops ;Comment below to use BL-Touch
;M574 X1 Y1 Z1 S0 ; set active low and disabled endstops

; BLTouch Endstops
M574 X1 Y1 S0 ; set active low and disabled endstops
M574 Z1 S2 ; Define Z to use Probe. Home to Min

; Z-Probe
M558 P5 H5 F500 T4000 X0 Y0 Z1 ; Set Z probe type/mode 5. H=Dive Height. F=Speed the X-carriage moves
;M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
G31 P25 X18 Y29 Z0.588 ; Z probe trigger value, offset in relation to nozzle. And trigger height adjustment
M557 X-12:215 Y22:195 S20 ; define mesh grid

; Heaters
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B3950 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 X200 ; configure PT100 for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M305 P2 X201 ; configure PT100 for heater 2
M143 H2 S300 ; set temperature limit for heater 2 to 300C

; BLTouch - Heaters
M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5

; Fans
M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 F0 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C

; Custom settings are not defined

;Mesh Bed Comp
M557 X0:200 Y45:175 S20

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Using Duet Web Control, I've set "Home All" and "Home Z" to move my BL-Touch probe over my heated bed before homing Z. However, when I try to do Mesh Bed leveling by issuing a G29 code, my printer immediately homes x and y to their minimums but never moves the x carriage or the heated bed so the BL-Touch will actually touch the heated bed.