@jay_s_uk un millon de gracias , era una cosa facil, pero se escapo a mi entender. gracias!!!!!!!!.. gracias!
A million thanks, it was an easy thing, but it escaped my understanding. Thank you!!!!!!!!.. Thank you!
Solucionado funciona correctamente!!
@jay_s_uk un millon de gracias , era una cosa facil, pero se escapo a mi entender. gracias!!!!!!!!.. gracias!
A million thanks, it was an easy thing, but it escaped my understanding. Thank you!!!!!!!!.. Thank you!
Solucionado funciona correctamente!!
google traslate:
Hello I have a problem I revived my cartesian machine after more than 1 year, and update from version 2.5 to 3.4.5. After having changed some new things that it brings and a week of investigating why the layer fan works with the slider of the DWC, but at the time of printing it does not activate.
Probe with gcodes from the previous week that I printed with the old version and with the new one not active.
I pass my settings to see if anyone gives a hand thank you!!!!. from Argentina:
PS: I also have this error: Error: Heater 0 fault: Heater 0 fault: temperature rising too slowly: expected 2.29°C/sec measured 0.65°C/sec. that I am investigating, if I heat it to 5 degrees, it does not mark the error. But it is a separate issue. Thank you
Hola tengo un problema reviví mi maquina cartesiana luego de mas de 1 año, y actualice de la version 2.5 a la 3.4.5. luego de haber cambiado alguna cosas nuevas que trae y una semana de investigar el por que el ventilador de capa funciona con el control deslizable del dwc, pero a la hora de imprimir no activa.
probe con gcodes de la semana anterior que imprimí con la version vieja y con la nueva no activa.
paso mi configuración a ver si alguno ne da una mano mil gracias!!!!. desde Argentina:
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.16 on Sun Jun 11 2023 20:22:41 GMT-0300 (hora estándar de Argentina)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"SERGIO2" ; set printer name
;M564 S1 H0
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 s1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X100 Y100 Z400 E410:410 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X-15 Y-15 Z0 S1 ; set axis minima
M208 X300 Y300 Z200 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"!xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S1 ; configure Z-probe endstop for low end on Z
; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z3.25 ; set Z probe trigger value, offset and trigger height
M557 X15:270 Y15:270 S20 ; define mesh grid
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S90 ; set temperature limit for heater 0 to 90C
M308 S1 P"e1temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e1heat" T1 ; create nozzle heater output on e1heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S240 ; set temperature limit for heater 1 to 240C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"VENT CAPA" S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"VENT HOTEND" S0 H1 T45 ; set fan 1 value. Thermostatic control is turned on
; Tools
M563 P0 D0 H1 F-1 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
T0
; Custom settings are not defined
Let's say what I want to do is 1 tool T0, another T1, AND THE T2 50/50%. so I choose T2 to mix
that would be the idea.
digamos que lo que quiero hacer es 1 herramienta T0, otrA T1, Y LA T2 50/50%. entonces elijo T2 para mezclar
esa seria la idea
M563 P0 S"PICO1" D0:1 H1 F0 ; Define tool 0
G10 P0 X0 Y0 Z0.10 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 S"PICO2" D0 H1 F0 ; Define tool 0
G10 P1 X0 Y0 Z0.10 ; Set tool 0 axis offsets
G10 P1 R0 S220 ; Set initial tool 0 active and standby temperatures to 0C
M563 P2 S"PICO" D1 H1 F0 ; Define tool 0
G10 P2 X0 Y0 Z0.10 ; Set tool 0 axis offsets
G10 P2 R0 S220 ; Set initial tool 0 active and standby temperatures to 0C
T0
M567 P0 E0.6:0.4
; ############################
; 4 - DRIVES
; ############################
M569 P0 S1 ; Physical drive 0 goes forwards
M569 P1 S1 ; Physical drive 1 goes forwards
M569 P2 S0 ; Physical drive 2 goes backwards
M569 P3 S0 ; Physical drive 3 goes forwards
M569 P4 S1 ; Physical drive 4 goes forwards
M350 X16 Y16 Z16 E16:16 I1 ; Configure microstepping with interpolation
; ############################
; 5 - SPEEDS
; ############################
; FEEDRATE CONVERSIONS
; 10MM/S = F600
; 20mm/s = F1200
; 40MM/S = F2400
; 70mm/s = F4200
; 120mm/s = F7200
M92 X100 Y100 Z400 E410:410 ; Set steps per mm
M201 X1200 Y1200 Z400 E600:6000 ; Set maximum accelerations (mm/s^2)
M203 X12000 Y12000 Z600 E12000:12000 ; Set maximum speeds (mm/min) Z360
;M204 P800 T800 ; Set printing and travel accelerations
M566 X300 Y300 Z30 E500:500.00 ; Set maximum instantaneous speed changes (mm/min) (Jerk) Z12
M906 X750.00 Y750.00 Z850.00 E950:950 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
;M593 F80
; Axis Limits
M208 X-15 Y-15 Z0 S1 ; Set axis minima
M208 X300 Y300 Z230 S0 ; Set axis maxima
; ############################
; 5 - HEATERS
; ############################
M305 P0 T100000 B3950 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S130 ; Set temperature limit for heater 0 to 130C
M305 P1 T100000 B3950 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S290 ; Set temperature limit for heater 1 to 275C
; ############################
; 8 - FANS
; ############################
M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; ############################
; 7 - TOOLS
; ############################
M563 P0 S"PICO" D0 H1 ; Define tool 1
G10 P0 X0 Y0 Z0.00 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
M563 P1 S"PICO2" D1 H1 ; Define tool 0
G10 P1 X0 Y0 Z0.00 ; Set tool 0 axis offsets
G10 P1 R0 S200 ; Set initial tool 0 active and standby temperatures to 0C
T0
M567 P0 E0.5:0.5.
voy a compartir mi config,g por si a alguno le sirve en el futuro. cuando haga mas pruebas voy a intentar hacer un post con mas detalles gracias.
I'm going to share my config, g in case it works for some in the future. when I do more tests I will try to make a post with more details thanks.
@deckingman @Veti gracias a ambos sin muy amable gracias a su colaboración logre que imprima, me faltan ajustes finos.
estaba bloqueado mentalmente.
@deckingman @Veti thank you both without very kind thanks to your collaboration I managed to print, I am missing fine adjustments.
I was mentally blocked
thanks
HELLO, SORRY FOR THE ANNOYANCE.
I'M USING RRF2 ON A DUETWIFI I'M TRYING TO SET UP A HOTEND 2 IN 1 OUT MIX FROM BIGTREETECH.
BUT I CAN'T PRINT, I CAN'T CONFIGURE THE FIRMWARE, THE TRUTH I'M TOTALLY LOST.
THIS LEGEND APPEARS WHEN TRYING TO PRINT WITH PRUSASLICER 2.3
"Attempting to extrude with no tool selected."
S I ATTACHED MY CONFIG.G THERE IT CAN HELP ME. FROM ALREADY THANKS.
; #############################
; 4 - DRIVES
; #############################
M569 P0 S1; Physical drive 0 goes forwards
M569 P1 S1; Physical drive 1 goes forwards
M569 P2 S0; Physical drive 2 goes backwards
M569 P3 S0; Physical drive 3 goes forwards
; M569 P4 S0; Physical drive 4 goes forwards
M350 X16 Y16 Z16 E16: 16 I1; Configure microstepping with interpolation
; #############################
; 5 - SPEEDS
; #############################
; FEEDRATE CONVERSIONS
; 10MM / S = F600
; 20mm / s = F1200
; 40MM / S = F2400
; 70mm / s = F4200
; 120mm / s = F7200
M92 X100 Y100 Z400 E410: 410; Set steps per mm
M201 X1200 Y1200 Z400 E600: 6000; Set maximum accelerations (mm / s ^ 2)
M203 X12000 Y12000 Z600 E12000: 12000; Set maximum speeds (mm / min) Z360
; M204 P800 T800; Set printing and travel accelerations
M566 X300 Y300 Z30 E500: 500.00; Set maximum instantaneous speed changes (mm / min) (Jerk) Z12
M906 X750.00 Y750.00 Z850.00 E950: 950 I30; Set motor currents (mA) and motor idle factor in per cent
M84 S30; Set idle timeout
; M593 F80
; Axis Limits
M208 X-15 Y-15 Z0 S1; Set axis minima
M208 X300 Y300 Z230 S0; Set axis maxima
; #############################
; 5 - HEATERS
; #############################
M305 P0 T100000 B3950 R4700; Set thermistor ADC parameters for heater 0
M143 H0 S130; Set temperature limit for heater 0 to 130C
M305 P1 T100000 B3950 R4700; Set thermistor ADC parameters for heater 1
M143 H1 S290; Set temperature limit for heater 1 to 275C
; #############################
; 8 - FANS
; #############################
M106 P0 S0 I0 F500 H-1; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
; #############################
; 7 - TOOLS
; #############################
M563 P0 S "PEAK" D0: 1 H1; Define tool 0
G10 P0 X0 Y0 Z0.00; Set tool 0 axis offsets
G10 P0 R0 S0; Set initial tool 0 active and standby temperatures to 0C
Hi, I would like to get into the thread of the conversation if you allow me.
I have a 3D touch (bltouch clone) similar to yours.
I'm connected to a master duet2. It responds to the basic test commands.
M208 SELF-TEST, DELAY AND EXPULS VERY WELL.
but when sending the g28 or g29 or g 30. the probe does not eject the PIN it only goes down and I must stop to not break the bed.
I know it must be some code that I'm missing. but I already ruined my last neurons in them. Please help. Thank you very much from Argentina.
GOOGLE TRANSLATOR
Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M558 P9 F100 H5 R0.2 R6000 A5 B1 ;P9 ES BLTOUCH,f100 (100/mm/m velocidad, h5 altura de movimiento sube 5mm, r0.2 espera 0.2 seg paracomenzar la prueba, A5 intenta 5 veces o hasta tener 2 resultadossimilares consecutivos, b1 apaga el hoend para evitar interferencias
G31 X0 Y0 Z0 P25 ; Set Z probe type to unmodulated and the dive height + speeds
M557 X0:140 Y10:150 S140 ; Define mesh grid
G31 X-15 Y-15 Z-0.08 P25 ; probe offset from nozzle, p is trigger value, set Z=0 for testing