Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. StephenRC
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 140
    • Best 0
    • Controversial 0
    • Groups 0

    StephenRC

    @StephenRC

    0
    Reputation
    1
    Profile views
    140
    Posts
    0
    Followers
    0
    Following
    Joined Last Online
    Location Florida Space Coast

    StephenRC Unfollow Follow

    Latest posts made by StephenRC

    • RE: Connecting and configuring filament-out sensors

      Some filament is transparent to infrared.

      posted in General Discussion
      StephenRCundefined
      StephenRC
    • RE: Cant connect to web controller after 1.19 upgrade

      The text editor can mess up the SetNetwork macro by using the wrong double quote marks. It has been previously reported for a Mac editor and I've found for Windows that Notepad++ does it also. One cure is to copy/paste from the web page to make the macro.

      posted in Firmware installation
      StephenRCundefined
      StephenRC
    • RE: Need Help For My DuetWiFi's First Test Print

      @AaronGreen:

      I rams the bed at G1 Z0.0 F1000, even though that's a different position to the place it rammed it on my test print (far right).

      I haven't continued with the process for fear of ramming the bed again.

      My hotend Z offset is: M307 H1 A250 C140 D5.3 B0 S1

      Whereas it was originally 0.9. I found that every time I did the Z0 calibration, the nozzle would always return to 5.4mm above the bed. Even if I set the physical height to 0.1, then told it to recognise it as Z0, then save it, it still would return to Z5.4 as Z0.

      Maybe I've done the Z0 calibration wrong and used the wrong setting to get it there…

      M307 doesn't set the z height. What you show is the hotend heater setting.

      posted in Tuning and tweaking
      StephenRCundefined
      StephenRC
    • RE: Web Based Configuration Tool

      The WiFi has two connectors for the z motor and they're driven by one driver.

      posted in General Discussion
      StephenRCundefined
      StephenRC
    • RE: Add plus and minus buttons for temperature, speed and extrusion.

      You can type in the temp you want in the box.

      posted in Firmware wishlist
      StephenRCundefined
      StephenRC
    • RE: Setting Z Height After Home - No Z Probe

      Use a macro, call it in both places. With a macro, you'll only have one place to change.

      posted in General Discussion
      StephenRCundefined
      StephenRC
    • RE: G31 Changing Z has no effect

      After editing config.g, you have to reboot for the changes to be used. I use macros to set the z offset for each type of filament and call the appropriate one in the slicer.

      posted in Tuning and tweaking
      StephenRCundefined
      StephenRC
    • RE: Fan Sensor & PWM max extr. or bed

      For the fan see https://www.duet3d.com/forum/thread.php?pid=6412#p6412

      posted in General Discussion
      StephenRCundefined
      StephenRC
    • RE: Shutdown or restart Duet Wifi

      Shutdown: turn off the power, nothing special needs to be done before doing that. If you have an all metal hotend, wait for it to get below 50c before turning off the power. This will help prevent the filament from jamming.

      Restart: via the web, hit the emergency stop button. On the board, hit the reset button. Another way: open config.g in DWC and save changes and it should prompt to reboot the board. Then there is the ol' standby: turn it off, wait for all the leds to go out, then turn it on.

      posted in General Discussion
      StephenRCundefined
      StephenRC
    • RE: Mosfet board vs SSR vs onboard

      Found this: http://www.chitu3d.com/3d-printer-parts-general-add-on-heated-bed-power-expansion-module-2/
      After following the url on the circuit board.

      The only spec is 25A max and only mentions 12vdc in determining the load.

      posted in Duet Hardware and wiring
      StephenRCundefined
      StephenRC