Thank you to everyone for the help I'm getting decent prints now I'll probably hooking up the bltouch in a day or so hope u can handle that by my self but I'm not holding my breath. Lol

Thank you to everyone for the help I'm getting decent prints now I'll probably hooking up the bltouch in a day or so hope u can handle that by my self but I'm not holding my breath. Lol

@phaedrux that was a genarated number that came from the upload I will change and test and also read the article you sent.

@phaedrux I'm not I new to the g coding I'm learning on the fly.

@mudcruzr I'm not sure I had to play with this thing just to get it working and not crash on every drive. But everything homes great.

Z moving .15 - .20mm up on printing starts at .40 jumps to .50 then .70mm and so on iv used two different slicers and it dose not change.My x and y seem to run fine im lost. Im running 2.02 firmware on the ender 3

; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S0 ; Drive 1 goes backwards
M569 P2 S1 ; Drive 2 goes backwards
M569 P3 S0 ; Drive 3 goes backwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 E420.00 ; Set steps per mm
M566 X900.00 Y900.00 Z900.00 E120.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; Set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z500.00 E250.00 ; Set accelerations (mm/s^2)
M906 X800.00 Y800.00 Z800.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X220 Y220 Z250 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 Z0 S1 ; Set active high endstops

; Z-Probe
;M558 P9 F100 H5 R0.2 T6000 A5 B1 ; Set Z probe type to unmodulated and the dive height + speeds
;G31 P25 X10 Y10 Z2 ; Set Z probe trigger value, offset and trigger height
;M307 H3 A-1 C-1 D-1 ; Define mesh grid
;M557 X10 Y10 Z0

; Heaters
M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
M307 H1 A273.5 C93.8 D4.9 S1.00 V23.9 B0 ; set parameters for heater 1
M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 X150 T"K" ; set thermocouple parameters for heater 1 x150 is thr right channel (terminal block) on the daughterboard. x151 is the right channel.
;M305 P1 X201 ; Configure thermocouple for heater 1
M143 H1 S325 ; Set temperature limit for heater 1 to 325C

; Fans
M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured

@wyvern thank you

I reinstalled everything hardware and software all endstops working everything moving in the right direction. Now trying to get the heater 1 to tune and not fault out everytime.

@dc42 yep that's how I have them hooked up.

@dc42 no I did not test them I will test them tonight after I post my settings.