Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. X4TEC
    • Profile
    • Following 0
    • Followers 0
    • Topics 5
    • Posts 33
    • Best 0
    • Controversial 0
    • Groups 0

    X4TEC

    @X4TEC

    0
    Reputation
    2
    Profile views
    33
    Posts
    0
    Followers
    0
    Following
    Joined Last Online
    Location Manchester

    X4TEC Unfollow Follow

    Latest posts made by X4TEC

    • RE: Fixed temperature to below 280

      Thanks all, must have been, that I set to low. Works fine since I set to 290.

      posted in Duet Hardware and wiring
      X4TECundefined
      X4TEC
    • RE: Fixed temperature to below 280

      Ill double check but I'm sure I adjusted M143 to 285 and it made no difference.

      posted in Duet Hardware and wiring
      X4TECundefined
      X4TEC
    • Fixed temperature to below 280

      I've installed the latest firmware on my duet WiFi with pt100 sensor board. I've checked config file, but if i try to set temp to anything beyond 280 printer just ignores the temp. I even tried gcode directly. Is it possible I have a hardware issue. I've got other issues with extrusion which I can't resolve. I did drop a screwdriver on the board. I advanced digs I can run?

      posted in Duet Hardware and wiring
      X4TECundefined
      X4TEC
    • RE: Second print height issues

      @Sabagmn:

      I would also double-check if you have a config-override.g file with G31 gcodes in it. Those will override your G31 settings in config.g
      Had that happen to me before and ended up having to comment them out.

      Hi Sabagmn. not got any G31 in my config-override file.

      posted in IR Height Sensor
      X4TECundefined
      X4TEC
    • RE: Second print height issues

      @Nylkos:

      Do you have G92 Z0 anywhere other then homez.g or homeall.g?

      Hi Nylkos, I don't have G92 in any of the home files,

      posted in IR Height Sensor
      X4TECundefined
      X4TEC
    • Second print height issues

      Hi anyone experience the following?

      I have a P3Steel with Duet Wifi and IR sensor.

      After a successful first print, I find that my second print always starts +.6mm above the correct Z point (ie if layer is .2 the print starts at .8, and reads as such on console). If I reset the electronics it prints correctly. The g-code job is exactly the same job, the printer homes the Z correctly, and I've done the paper under the nozzle check, but I can not work out where the extra .6mm is coming from.

      posted in IR Height Sensor
      X4TECundefined
      X4TEC
    • RE: Prometheus multi filament system

      PS the extruders are not great!

      posted in Duet Hardware and wiring
      X4TECundefined
      X4TEC
    • RE: Prometheus multi filament system

      I've just manged a print, via a convoluted post processing script for Simplify3D, now i need to tune

      posted in Duet Hardware and wiring
      X4TECundefined
      X4TEC
    • RE: Prometheus multi filament system

      CaLviNx, this is my first Bowen, much prefer a direct drive, totally agree the acrylic extrudes are not that brilliant. Have you switched yours out for the one in the picture?

      posted in Duet Hardware and wiring
      X4TECundefined
      X4TEC
    • RE: Prometheus multi filament system

      I've finally got around to building a machine, now I need to workout all the settings. Anyone tried this yet?

      posted in Duet Hardware and wiring
      X4TECundefined
      X4TEC