Posts made by Xanaden

I thing both is working.. M408 Is what i was looking for but i will check the HTTP Requests thank you

Hello

Iam quite new to Smart Home and FHEM stuff but the last few days i got my FHEM Smarthome server to conntect to Telenet and do the preheat the Printer Next door.
well i know this is kinda useless because i need to start the Browser anyway to load the file iam looking for a way to read the status from the Print so i get notified or do some other stuff.

So is ther a easy way using telenet or something similar to read the status?

Thank you

Pin 1 zu Pin 2 von 4.0 Ohm and Pin 1 to Pin 3 42.4Ohm and Pin 2 to Pin 3 40.2 Ohm

@T3P3Tony Sure i can but it looks like 3.3V is missing.

Still Dunno why my "old" duet ethernet is still working fine on the same machine.

Hello

My Reseller told me to open a Thread in this Forum because i bought a new Duet with 7" Panel last week from Makerdise. I used it 5 Days with out a Problem yesterday during print with out touching the wiring the Panal smoked and the LED turn dark. The Wiring is professionally done ( its my job) nothing went lose.

If i turn the Power on now the thers only the 2 Power Led Blue and Red on. Display and the rest stays dark.

I was using a Duet Ethernet befor on this printer for about 6 Month only wanted to switch to the Wifi and the 7" display now. My other 4 Duet´s have had no Single problems until now.
After the "crash" is switched back to the a Other Duet on this printer and have no problems ther too


Okay so i have a 0.02 deviation in the bltouch i still lowerd the probe and the max ACC Z speed but still get a deviation around 0.19 each G32 if i do 10 times in a row

Any ideas what i migh doing wrong?

Hello

i Found some more problems with my BLtouch / Corexy printer maybe you guys have a Solution.
Everytime i start a print with the same gcode i have a different first layer.
Sometimes its to close sometimes to far away even if i use G29 before every print.

Also each time i start G32 (successively)i have an deviation about 0.3
I have tighten the Z Couppler, moving z very slow and cant measure any offset on Z moving

Is ther a way to test the Bltouch repeatability like M48 P4 X200 Y200 V2 E L2 in marlin?

M558 P5 X0 Y0 Z1 H5 F120 T6000 ; Set Z Probe to type Switch or Digital output
G31 P50 X63 Y-65 Z1.8
M557 X65:340 Y30:380 S70 ; Define mesh grid

M584 X0 Y1 Z2:3 E4:5:6
M671 X-75:480 Y240:240 S2

G28 XY ; home
G28 Z
M401 ; deploy Z probe
G30 P0 X65 Y190 Z-99999 ; probe near a leadscrew
G30 P1 X370 Y190 Z-99999 S2 ; probe near a leadscrew

M402 ; retract probe
G28 Z

Any idea what iam doing wrong?

Thank you for that.
Now i still have trouble with the G32 command.

Iam leveling my axis like 0.5mm off and run G32 After G32 is over my axis are off like 1.4mm so what iam doing wrong?

edit

I tried it multible times in a row and its getting worse every time untill i get the Limit Error

Bed.g
G28 XY ; home
G28 Z
M401
G30 P1 X370 Y190 Z-99999 ; deploy Z probe
G30 P0 X65 Y190 Z-99999 S2 ; probe near a leadscrew
; probe near a leadscrew

M402 ; retract probe

Config.g
M584 X0 Y1 Z2:3 E4:5:6

M671 X-15:380 Y240:240 S2 as the last command

1.19
Homez :
; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool on Tue Oct 10 2017 16:36:21 GMT+0200 (Mitteleuropäische Sommerzeit)

; Lift Z relatively to current position
G91
G1 Z5 F6000

; Move Z down until the switch triggers
G1 Z-455 S1 F1800

; Back to absolute positioning
G90

; Tell the firmware where we are
G92 Z0

; Uncomment the following lines to lift Z after probing
;G91
;G1 Z5 F100
;G90

Homeall

; Move Z down until the switch triggers
G1 Z-455 F1800 S1

What do i need to Change to use the Bltouch as Z endstop?

Thanks that worked for the g29 but dose Not solve the Problem with the g30 or the Homeing with the bltouch.

Hello
first i want to say sorry for my bad englisch i tried my best to understand the Wiki and to explain my problem here.

I did Setup my BL Touch using the Wiki and all worked good thers is only one think i do not understand. If i start the G29 right after the G28 the sensor Crashes and Blink´s because the probe cant deploy complitly. Is this normal or just a mather of wrong installation from my side?

Is it Posible to use the Bltouch for as a Homeing endstop? if so what do i need to do that thes deploying the probe if i hit G28?

I also tried to get the G30 Bed Leveling running but i guess iam missing something important.
Iam Using 2 Leadscrews with 2 Z motors on driver 2/3 middel left and middel Right from my 400*400 bed. Here is what i did setup:

Config.g
M584 X0 Y1 Z2:3 E4:5:6
M671 X-15:380 Y250:250 S0.5 <- What do i need to set here i just dont understand it.

Bed.G
G28 ; home
M401 ; deploy Z probe
G30 P0 X0 Y250 Z-99999 ; probe near a leadscrew
G30 P1 X330 Y250 Z-99999 S2 ; probe near a leadscrew

M402 ; retract probe

Right now if i hit the G30 hes Deploying the probe and the Bltouch blinks again because of the deploying issue if i lift Z and hit G30 after that he´s just moving up until the Probe is triggert and then it stops.

I really hope its somewhat
understandable what iam trying to ask.