3d printer ender 3 pro
and this is the whole file for confik.g
; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Mon Jan 07 2019 23:53:31 GMT+0200 (Eastern European Standard Time)
; General preferences
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
; Network
M550 PEnder3 ; Set machine name
M552 S1 ; Enable network
;M587 S"FiberSwag_IoT" P"SonosErGud123" I10.0.1.9 J10.0.1.1 K255.255.255.0 ; Configure access point and IP addresses. You can delete this line once connected
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet
; Drives
M569 P0 S0 ; Drive 0 goes backwards
M569 P1 S0 ; Drive 1 goes backwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes backwards
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80.00 Y79.892 Z400.00 E94.50 ; Set steps per mm
M566 X900.00 Y900.00 Z12.00 E300.00 ; Set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z300.00 E18000.00 ; Set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; Set accelerations (mm/s^2)
M906 X600.00 Y600.00 Z600.00 E800.00 I50 ; Set motor currents (mA) and motor idle factor in per cent
M84 S60 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X235 Y235 Z250 S0 ; Set axis maxima
; Endstops
; M574 X1 Y1 S1 ; Set active high endstops
M574 X1 Y1 S1 ; X home to min. Y home to max. Normally Closed limit switches.
; Z-Probe
M574 Z1 S2 ; Set endstops controlled by probe
M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T6000 X0 Y0 Z1 ; Set Z probe type to bltouch and the dive height + speeds
G31 P25 X48 Y-2 Z1.19 ; Set Z probe trigger value, offset and trigger height
M557 X50:230 Y50:230 S10 ; Define mesh grid
; Heaters
M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120 ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280 ; Set temperature limit for heater 1 to 280C
; Fans
M106 P0 S255 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S255 I0 F500 H1 T45 ; Set fan 1 to turn on full speed when Hotend reaches 45
M106 P2 T45:65 H100:101:102 ; Set fan 2 to turn on when MCU reaches 45 and reach full speed when MCU reaches 65 or any TMC2660 report over-temperature
; Tools
M563 P0 D0 H1 ; Define tool 0
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
; Automatic saving after power loss is not enabled
; Custom settings are not configured
; Miscellaneous
T0 ; Select first tool