Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Wifi/Web Console issues

    Scheduled Pinned Locked Moved Solved
    General Discussion
    7
    44
    2.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • T3P3Tonyundefined
      T3P3Tony administrators @Shaun
      last edited by

      @shaun said in Wifi/Web Console issues:

      @t3p3tony I can only get it connected when i run YAT

      M552 s0
      m587 s"name" p"password"
      M552 s1

      Then it connects, try the web console which honestly struggles. WHen i manage to get into the settings to confirm that M552 S1 is set in the config.g it returns a "make sure your device is connected"

      When i shut down and then transfer to the printer, wifi doesnt even come on. I get no blue light once i move the board.

      Ive cleared the saved details and then set them using M587, i have even tried DHCP and Static details.

      Can you run M122, from YAT, one the wifi is connected. It should show what the DB of the wifi signal you are getting.

      When you put it in the printer, is that now in a metal enclosure, or is the printer further form the wifi router?

      www.duet3d.com

      T3P3Tonyundefined Shaunundefined 2 Replies Last reply Reply Quote 0
      • A Former User?
        A Former User
        last edited by

        Need to configure line endings in YAT or use another terminal btw.

        when you start editing config.json its probably time to move off the web configurator and stick to only editing config.g as well; duet boards does not read config.json.

        Shaunundefined 1 Reply Last reply Reply Quote 0
        • T3P3Tonyundefined
          T3P3Tony administrators @T3P3Tony
          last edited by

          @Shaun I just see you have posted part of M122 above. If you set YAT to use the correct line endings you will get nicer output that wont be truncated.

          Go to Terminal/Settings/Text Settings and change the EOL sequence to <LF>.

          www.duet3d.com

          Shaunundefined 1 Reply Last reply Reply Quote 0
          • A Former User?
            A Former User
            last edited by

            (OT, when YAT is the recommended terminal, I'd change the firmware EOL to be compatible with the default settings of YAT)

            T3P3Tonyundefined 1 Reply Last reply Reply Quote 0
            • T3P3Tonyundefined
              T3P3Tony administrators @A Former User
              last edited by

              @bearer good point, or at least send both.

              www.duet3d.com

              1 Reply Last reply Reply Quote 0
              • Shaunundefined
                Shaun @T3P3Tony
                last edited by

                @t3p3tony Let me clarify, WIFI now connects when i run M552 S0 then M552 S1. Webconsole also responds pretty quickly.

                When moving the board to the printer i power it without connecting it or placing it into anything. Simply laying it down in the foam from inside the shipping box. The wifi blue light doesnt even blink once.

                Signal strength isnt a problem, i checked the strength many times as i use to have the Pi there without any issues.

                Do you have any suggestions in getting the wifi fired up without having to send code to the board via YAT

                1 Reply Last reply Reply Quote 0
                • Shaunundefined
                  Shaun @A Former User
                  last edited by

                  @bearer I hear you, but i only managed to get a stable connection once i added her SID and Password to Config.json so its clearly reading from it. I dont have those details in the Config.g.

                  A Former User? 1 Reply Last reply Reply Quote 0
                  • Shaunundefined
                    Shaun @T3P3Tony
                    last edited by

                    @t3p3tony said in Wifi/Web Console issues:

                    @Shaun I just see you have posted part of M122 above. If you set YAT to use the correct line endings you will get nicer output that wont be truncated.

                    Go to Terminal/Settings/Text Settings and change the EOL sequence to <LF>.

                    Noted

                    1 Reply Last reply Reply Quote 0
                    • A Former User?
                      A Former User @Shaun
                      last edited by A Former User

                      @shaun said in Wifi/Web Console issues:

                      so its clearly reading from it.

                      No.

                      @shaun said in Wifi/Web Console issues:

                      I dont have those details in the Config.g.

                      yes, thats correct, after you enter the details with M587 it is stored in the wifi modules flash memory. which is part of the reason the documentations tells you not to use M587 (to store wifi details) in config.g, the wifi module is not enabled at the time config.g is executed and saving the wifi details every time would put unnecessary wear on the wifi flash memory.

                      Shaunundefined 1 Reply Last reply Reply Quote 1
                      • Shaunundefined
                        Shaun @A Former User
                        last edited by

                        @bearer said in Wifi/Web Console issues:

                        @shaun said in Wifi/Web Console issues:

                        so its clearly reading from it.

                        No.

                        @shaun said in Wifi/Web Console issues:

                        I dont have those details in the Config.g.

                        yes, thats correct, after you enter the details with M587 it is stored in the wifi modules flash memory. which is part of the reason the documentations tells you not to use M587 (to store wifi details) in config.g, the wifi module is not enabled at the time config.g is executed and saving the wifi details every time would put unnecessary wear on the wifi flash memory.

                        OK, so could you help me figure out why the wifi is not even coming on when i power the board? At which point is M552 S0 read from Flash?

                        Phaedruxundefined A Former User? 2 Replies Last reply Reply Quote 0
                        • MrsDelishundefined
                          MrsDelish
                          last edited by

                          M552 S0 = turn off networking, you do not want that in your config.g if you want networking.

                          config.g that contains this should connect if a ssid and pw is previously set.
                          ; Network
                          M552 S1 ; enable network
                          M586 P0 S1 ; enable HTTP
                          M586 P1 S0 ; disable FTP
                          M586 P2 S0 ; disable Telnet

                          gcode wiki M552

                          1 Reply Last reply Reply Quote 1
                          • Phaedruxundefined
                            Phaedrux Moderator @Shaun
                            last edited by

                            @shaun said in Wifi/Web Console issues:

                            why the wifi is not even coming on when i power the board?

                            What is the power supply? Do the rest of the lights and everything else come on?

                            When it is powered by the PSU, can you connect via USB as well and send M122 with the correct YAT line endings and report what the diagnostic replies with?

                            Z-Bot CoreXY Build | Thingiverse Profile

                            Shaunundefined 1 Reply Last reply Reply Quote 1
                            • Shaunundefined
                              Shaun @Phaedrux
                              last edited by Shaun

                              @phaedrux said in Wifi/Web Console issues:

                              @shaun said in Wifi/Web Console issues:

                              why the wifi is not even coming on when i power the board?

                              What is the power supply? Do the rest of the lights and everything else come on?

                              When it is powered by the PSU, can you connect via USB as well and send M122 with the correct YAT line endings and report what the diagnostic replies with?

                              Ill get this when i get home, PSU is as per vendor recommendations.

                              Red light by the USB power port, 2 more lights to the left of that. No blue wifi light.

                              1 Reply Last reply Reply Quote 0
                              • Phaedruxundefined
                                Phaedrux Moderator
                                last edited by

                                Understood.

                                With the line endings of YAT changed we will be able to see the end of the diagnostic report which contains the wifi section. Without that we're kind of blind as to what's going on.

                                Can you also include the contents of config.g from the /sys folder on the SD card?

                                That contains your current configuration and what you will be editing going forward. It can be edited from the web interface once you can get reliably connected to it. Until then it may require pulling the SD card unfortunately.

                                Z-Bot CoreXY Build | Thingiverse Profile

                                1 Reply Last reply Reply Quote 0
                                • A Former User?
                                  A Former User @Shaun
                                  last edited by

                                  @shaun said in Wifi/Web Console issues:

                                  OK, so could you help me figure out why the wifi is not even coming on when i power the board?

                                  Sure, when you set aside your assumptions as start doing as suggested. The output from M587 and all of the M122 output please.

                                  Shaunundefined 1 Reply Last reply Reply Quote 0
                                  • Shaunundefined
                                    Shaun @A Former User
                                    last edited by

                                    @bearer said in Wifi/Web Console issues:

                                    M122

                                    M587<CR>
                                    M587: Failed to retrieve network list
                                    ok
                                    M122 <CR>
                                    === Diagnostics ===
                                    RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
                                    Board ID: 08DGM-9T6BU-FG3SN-6J9F4-3SD6R-TUZHF
                                    Used output buffers: 1 of 24 (1 max)
                                    === RTOS ===
                                    Static ram: 25680
                                    Dynamic ram: 93244 of which 0 recycled
                                    Exception stack ram used: 304
                                    Never used ram: 11844
                                    Tasks: NETWORK(ready,1876) HEAT(blocked,1236) MAIN(running,4184) IDLE(ready,160)
                                    Owned mutexes:
                                    === Platform ===
                                    Last reset 00:00:55 ago, cause: power up
                                    Last software reset at 2019-09-02 22:49, reason: User, spinning module GCodes, available RAM 11844 bytes (slot 3)
                                    Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x04433000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
                                    Error status: 0
                                    Free file entries: 10
                                    SD card 0 detected, interface speed: 20.0MBytes/sec
                                    SD card longest block write time: 0.0ms, max retries 0
                                    MCU temperature: min 26.5, current 30.2, max 30.5
                                    Supply voltage: min 0.6, current 1.7, max 1.7, under voltage events: 0, over voltage events: 0, power good: no
                                    Driver 0: ok, SG min/max not available
                                    Driver 1: ok, SG min/max not available
                                    Driver 2: ok, SG min/max not available
                                    Driver 3: ok, SG min/max not available
                                    Driver 4: ok, SG min/max not available
                                    Date/time: 1970-01-01 00:00:00
                                    Cache data hit count 101580001
                                    Slowest loop: 0.16ms; fastest: 0.06ms
                                    I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                                    === Move ===
                                    Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
                                    Bed compensation in use: none, comp offset 0.000
                                    === DDARing ===
                                    Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
                                    === Heat ===
                                    Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
                                    === GCodes ===
                                    Segments left: 0
                                    Stack records: 1 allocated, 0 in use
                                    Movement lock held by null
                                    http is idle in state(s) 0
                                    telnet is idle in state(s) 0
                                    file is idle in state(s) 0
                                    serial is ready with "M122 " in state(s) 0
                                    aux is idle in state(s) 0
                                    daemon is idle in state(s) 0
                                    queue is idle in state(s) 0
                                    autopause is idle in state(s) 0
                                    Code queue is empty.
                                    === Network ===
                                    Slowest loop: 0.15ms; fastest: 0.00ms
                                    Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
                                    HTTP sessions: 0 of 8

                                    • WiFi -
                                      Network state is disabled
                                      WiFi module is disabled
                                      Failed messages: pending 2779096485, notready 2779096485, noresp 2779096485
                                      Socket states: 0 0 0 0 0 0 0 0
                                      m552 s0
                                      ok
                                      WiFi module started
                                      m122
                                      === Diagnostics ===
                                      RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
                                      Board ID: 08DGM-9T6BU-FG3SN-6J9F4-3SD6R-TUZHF
                                      Used output buffers: 1 of 24 (10 max)
                                      === RTOS ===
                                      Static ram: 25680
                                      Dynamic ram: 93288 of which 0 recycled
                                      Exception stack ram used: 304
                                      Never used ram: 11800
                                      Tasks: NETWORK(ready,1656) HEAT(blocked,1236) MAIN(running,3768) IDLE(ready,160)
                                      Owned mutexes:
                                      === Platform ===
                                      Last reset 00:04:05 ago, cause: power up
                                      Last software reset at 2019-09-02 22:49, reason: User, spinning module GCodes, available RAM 11844 bytes (slot 3)
                                      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x04433000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
                                      Error status: 0
                                      Free file entries: 10
                                      SD card 0 detected, interface speed: 20.0MBytes/sec
                                      SD card longest block write time: 0.0ms, max retries 0
                                      MCU temperature: min 30.2, current 31.6, max 31.7
                                      Supply voltage: min 1.7, current 1.7, max 1.7, under voltage events: 0, over voltage events: 0, power good: no
                                      Driver 0: ok, SG min/max not available
                                      Driver 1: ok, SG min/max not available
                                      Driver 2: ok, SG min/max not available
                                      Driver 3: ok, SG min/max not available
                                      Driver 4: ok, SG min/max not available
                                      Date/time: 1970-01-01 00:00:00
                                      Cache data hit count 461723815
                                      Slowest loop: 99.34ms; fastest: 0.06ms
                                      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                                      === Move ===
                                      Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
                                      Bed compensation in use: none, comp offset 0.000
                                      === DDARing ===
                                      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
                                      === Heat ===
                                      Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
                                      === GCodes ===
                                      Segments left: 0
                                      Stack records: 1 allocated, 0 in use
                                      Movement lock held by null
                                      http is idle in state(s) 0
                                      telnet is idle in state(s) 0
                                      file is idle in state(s) 0
                                      serial is ready with "m122" in state(s) 0
                                      aux is idle in state(s) 0
                                      daemon is idle in state(s) 0
                                      queue is idle in state(s) 0
                                      autopause is idle in state(s) 0
                                      Code queue is empty.
                                      === Network ===
                                      Slowest loop: 1.22ms; fastest: 0.00ms
                                      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
                                      HTTP sessions: 0 of 8
                                    • WiFi -
                                      Network state is running
                                      WiFi module is idle
                                      Failed messages: pending 0, notready 0, noresp 0
                                      WiFi firmware version 1.23
                                      WiFi MAC address 84:f3:eb:41:4e:f8
                                      WiFi Vcc 3.39, reset reason Turned on by main processor
                                      WiFi flash size 4194304, free heap 30176
                                      Socket states: 0 0 0 0 0 0 0 0
                                      ok
                                      m587
                                      Remembered networks:
                                      Spiffy IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
                                      ok
                                      M587 s"Spiffy" p"Password1"
                                      ok
                                      M587
                                      Remembered networks:
                                      Spiffy IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0
                                      ok
                                      m122
                                      === Diagnostics ===
                                      RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
                                      Board ID: 08DGM-9T6BU-FG3SN-6J9F4-3SD6R-TUZHF
                                      Used output buffers: 1 of 24 (10 max)
                                      === RTOS ===
                                      Static ram: 25680
                                      Dynamic ram: 93288 of which 0 recycled
                                      Exception stack ram used: 304
                                      Never used ram: 11800
                                      Tasks: NETWORK(ready,1656) HEAT(blocked,1236) MAIN(running,3756) IDLE(ready,160)
                                      Owned mutexes:
                                      === Platform ===
                                      Last reset 00:05:15 ago, cause: power up
                                      Last software reset at 2019-09-02 22:49, reason: User, spinning module GCodes, available RAM 11844 bytes (slot 3)
                                      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x04433000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
                                      Error status: 0
                                      Free file entries: 10
                                      SD card 0 detected, interface speed: 20.0MBytes/sec
                                      SD card longest block write time: 0.0ms, max retries 0
                                      MCU temperature: min 31.4, current 32.3, max 32.4
                                      Supply voltage: min 1.7, current 1.7, max 1.7, under voltage events: 0, over voltage events: 0, power good: no
                                      Driver 0: ok, SG min/max not available
                                      Driver 1: ok, SG min/max not available
                                      Driver 2: ok, SG min/max not available
                                      Driver 3: ok, SG min/max not available
                                      Driver 4: ok, SG min/max not available
                                      Date/time: 1970-01-01 00:00:00
                                      Cache data hit count 602028484
                                      Slowest loop: 0.33ms; fastest: 0.06ms
                                      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                                      === Move ===
                                      Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
                                      Bed compensation in use: none, comp offset 0.000
                                      === DDARing ===
                                      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
                                      === Heat ===
                                      Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
                                      === GCodes ===
                                      Segments left: 0
                                      Stack records: 1 allocated, 0 in use
                                      Movement lock held by null
                                      http is idle in state(s) 0
                                      telnet is idle in state(s) 0
                                      file is idle in state(s) 0
                                      serial is ready with "m122" in state(s) 0
                                      aux is idle in state(s) 0
                                      daemon is idle in state(s) 0
                                      queue is idle in state(s) 0
                                      autopause is idle in state(s) 0
                                      Code queue is empty.
                                      === Network ===
                                      Slowest loop: 0.14ms; fastest: 0.00ms
                                      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
                                      HTTP sessions: 0 of 8
                                    • WiFi -
                                      Network state is running
                                      WiFi module is idle
                                      Failed messages: pending 0, notready 0, noresp 0
                                      WiFi firmware version 1.23
                                      WiFi MAC address 84:f3:eb:41:4e:f8
                                      WiFi Vcc 3.39, reset reason Turned on by main processor
                                      WiFi flash size 4194304, free heap 30176
                                      Socket states: 0 0 0 0 0 0 0 0
                                      ok

                                    .....

                                    1 Reply Last reply Reply Quote 0
                                    • Shaunundefined
                                      Shaun
                                      last edited by

                                      Rebooting device.....
                                      m122
                                      === Diagnostics ===
                                      RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
                                      Board ID: 08DGM-9T6BU-FG3SN-6J9F4-3SD6R-TUZHF
                                      Used output buffers: 1 of 24 (1 max)
                                      === RTOS ===
                                      Static ram: 25680
                                      Dynamic ram: 93244 of which 0 recycled
                                      Exception stack ram used: 244
                                      Never used ram: 11904
                                      Tasks: NETWORK(ready,1876) HEAT(blocked,1236) MAIN(running,4468) IDLE(ready,160)
                                      Owned mutexes:
                                      === Platform ===
                                      Last reset 00:00:37 ago, cause: power up
                                      Last software reset at 2019-09-02 22:49, reason: User, spinning module GCodes, available RAM 11844 bytes (slot 3)
                                      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x04433000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
                                      Error status: 0
                                      Free file entries: 10
                                      SD card 0 detected, interface speed: 20.0MBytes/sec
                                      SD card longest block write time: 0.0ms, max retries 0
                                      MCU temperature: min 31.1, current 33.0, max 33.2
                                      Supply voltage: min 1.5, current 1.7, max 1.7, under voltage events: 0, over voltage events: 0, power good: no
                                      Driver 0: ok, SG min/max not available
                                      Driver 1: ok, SG min/max not available
                                      Driver 2: ok, SG min/max not available
                                      Driver 3: ok, SG min/max not available
                                      Driver 4: ok, SG min/max not available
                                      Date/time: 1970-01-01 00:00:00
                                      Cache data hit count 68946894
                                      Slowest loop: 0.15ms; fastest: 0.06ms
                                      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                                      === Move ===
                                      Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
                                      Bed compensation in use: none, comp offset 0.000
                                      === DDARing ===
                                      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
                                      === Heat ===
                                      Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
                                      === GCodes ===
                                      Segments left: 0
                                      Stack records: 1 allocated, 0 in use
                                      Movement lock held by null
                                      http is idle in state(s) 0
                                      telnet is idle in state(s) 0
                                      file is idle in state(s) 0
                                      serial is ready with "m122" in state(s) 0
                                      aux is idle in state(s) 0
                                      daemon is idle in state(s) 0
                                      queue is idle in state(s) 0
                                      autopause is idle in state(s) 0
                                      Code queue is empty.
                                      === Network ===
                                      Slowest loop: 0.15ms; fastest: 0.00ms
                                      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
                                      HTTP sessions: 0 of 8

                                      • WiFi -
                                        Network state is disabled
                                        WiFi module is disabled
                                        Failed messages: pending 2779096485, notready 2779096485, noresp 2779096485
                                        Socket states: 0 0 0 0 0 0 0 0
                                        ok

                                      Config.g
                                      ; Configuration file for Duet WiFi (firmware version 2.03)
                                      ; executed by the firmware on start-up
                                      ;
                                      ; generated by RepRapFirmware Configuration Tool v2.0.0 on Sun Sep 01 2019 16:01:34 GMT+0100 (British Summer Time)

                                      ; General preferences
                                      G90 ; send absolute coordinates...
                                      M83 ; ...but relative extruder moves
                                      M550 P"CR10" ; set printer name
                                      M911 S10 R11 P'M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000' ; set voltage thresholds and actions to run on power loss

                                      ; Drives
                                      M569 P0 S1 ; physical drive 0 goes forwards
                                      M569 P1 S1 ; physical drive 1 goes forwards
                                      M569 P2 S1 ; physical drive 2 goes forwards
                                      M569 P3 S1 ; physical drive 3 goes forwards
                                      M584 X0 Y1 Z2 E3 ; set drive mapping
                                      M350Z16 I0 ; configure microstepping without interpolation
                                      M350X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                                      M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
                                      M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                                      M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
                                      M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
                                      M906 X950 Y950 Z950 E950 I30 ; set motor currents (mA) and motor idle factor in per cent
                                      M84 S30 ; Set idle timeout

                                      ; Axis Limits
                                      M208 X0 Y0 Z0 S1 ; set axis minima
                                      M208 X300 Y300 Z400 S0 ; set axis maxima

                                      ; Endstops
                                      M574 X1 Y1 Z1 S1 ; set active high endstops
                                      M574 Z1 S3 ; set endstops controlled by motor stall detection

                                      ; Z-Probe
                                      M574 Z1 S2 ; set endstops controlled by probe
                                      M558 P5 H5 F0 T6000 ; set Z probe type to switch and the dive height + speeds
                                      G31 P0 X0 Y0 Z0 ; set Z probe trigger value, offset and trigger height
                                      M557 X15:215 Y15:195 S20 ; define mesh grid

                                      ; Heaters
                                      M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
                                      M143 H0 S120 ; set temperature limit for heater 0 to 120C
                                      M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1
                                      M143 H1 S280 ; set temperature limit for heater 1 to 280C

                                      ; Fans
                                      M106 P0 S0 I0 F500 H T45 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
                                      M106 P1 S1 I0 F500 H-1 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
                                      M106 P2 S1 I0 F500 H-1 ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off

                                      ; Tools
                                      M563 P0 D0 H1 F0 ; define tool 0
                                      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                                      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                                      ; Network
                                      M552 S1 ; enable network
                                      M586 P0 S1 ; enable HTTP
                                      M586 P1 S0 ; disable FTP
                                      M586 P2 S0 ; disable Telnet

                                      ; Custom settings are not defined

                                      m115
                                      FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.03 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2019-06-13b2
                                      ok

                                      Anything else?

                                      1 Reply Last reply Reply Quote 0
                                      • A Former User?
                                        A Former User
                                        last edited by

                                        Does it make any difference using M552 S1 P"Spiffy"

                                        if you have a look at the markdown page, especially the code block, you'll be able to make the output a lot easier to read
                                        https://commonmark.org/help/

                                        1 Reply Last reply Reply Quote 0
                                        • Phaedruxundefined
                                          Phaedrux Moderator
                                          last edited by

                                          From the console can you please send the following:

                                          M552 S0
                                          M588 S"*"
                                          M587 s"Spiffy" p"Password1"
                                          M552 S1
                                          M122
                                          

                                          This will take the wifi module to idle, clear all saved SSIDs, re-add your SSID, and re-enable the module and hopefully connect. Then the diagnostic should show the connection stats.

                                          How far away is the access point from the printer?
                                          Do your other devices get a strong signal in that area?
                                          Is the access point 2.4Ghz? 5Ghz won't work.

                                          Z-Bot CoreXY Build | Thingiverse Profile

                                          1 Reply Last reply Reply Quote 0
                                          • Shaunundefined
                                            Shaun
                                            last edited by

                                            m122
                                            === Diagnostics ===
                                            RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
                                            Board ID: 08DGM-9T6BU-FG3SN-6J9F4-3SD6R-TUZHF
                                            Used output buffers: 1 of 24 (1 max)
                                            === RTOS ===
                                            Static ram: 25680
                                            Dynamic ram: 93244 of which 0 recycled
                                            Exception stack ram used: 304
                                            Never used ram: 11844
                                            Tasks: NETWORK(ready,1244) HEAT(blocked,1236) MAIN(running,4468) IDLE(ready,160)
                                            Owned mutexes:
                                            === Platform ===
                                            Last reset 00:12:58 ago, cause: power up
                                            Last software reset at 2019-09-02 22:49, reason: User, spinning module GCodes, available RAM 11844 bytes (slot 3)
                                            Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x04433000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
                                            Error status: 0
                                            Free file entries: 10
                                            SD card 0 detected, interface speed: 20.0MBytes/sec
                                            SD card longest block write time: 0.0ms, max retries 0
                                            MCU temperature: min 32.6, current 35.4, max 35.5
                                            Supply voltage: min 1.5, current 1.7, max 1.7, under voltage events: 0, over voltage events: 0, power good: no
                                            Driver 0: ok, SG min/max not available
                                            Driver 1: ok, SG min/max not available
                                            Driver 2: ok, SG min/max not available
                                            Driver 3: ok, SG min/max not available
                                            Driver 4: ok, SG min/max not available
                                            Date/time: 1970-01-01 00:00:00
                                            Cache data hit count 2516579683
                                            Slowest loop: 99.70ms; fastest: 0.06ms
                                            I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                                            === Move ===
                                            Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
                                            Bed compensation in use: none, comp offset 0.000
                                            === DDARing ===
                                            Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
                                            === Heat ===
                                            Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
                                            === GCodes ===
                                            Segments left: 0
                                            Stack records: 1 allocated, 0 in use
                                            Movement lock held by null
                                            http is idle in state(s) 0
                                            telnet is idle in state(s) 0
                                            file is idle in state(s) 0
                                            serial is ready with "m122" in state(s) 0
                                            aux is idle in state(s) 0
                                            daemon is idle in state(s) 0
                                            queue is idle in state(s) 0
                                            autopause is idle in state(s) 0
                                            Code queue is empty.
                                            === Network ===
                                            Slowest loop: 15.36ms; fastest: 0.00ms
                                            Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
                                            HTTP sessions: 0 of 8

                                            • WiFi -
                                              Network state is running
                                              WiFi module is connected to access point
                                              Failed messages: pending 0, notready 0, noresp 0
                                              WiFi firmware version 1.23
                                              WiFi MAC address 84:f3:eb:41:4e:f8
                                              WiFi Vcc 3.39, reset reason Exception
                                              WiFi flash size 4194304, free heap 23696
                                              WiFi IP address 192.168.0.19
                                              WiFi signal strength -60dBm, reconnections 0, sleep mode modem
                                              Socket states: 0 0 0 0 0 0 0 0
                                              ok

                                            So now my problem is still powering down and then moving the board to my printer. wifi remains disabled

                                            Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA