Problem with Magnetic Sensor
-
14 hours later and About 100 meters of filament to go on this 445 meter job. After tweaking sensitivity, ratios, extruder rate, print speed and closely visually monitoring print quality, I found the filament monitor setting that work with this less than satisfying wood PLA filament.
They are not ideal, but unless one is down with running about 75 % print speed, this is what worked. Slowing the print speed increased the min reported back up to upper 60s percentage.
Extrusion at 100%, speed at 100% (80mm/sec max), temp mid range of filament noted temp range (200c in this case) and the following:**8:23:33 AM
M591 D0
Duet3D magnetic filament monitor on input 3, enabled, sensitivity 28.02mm/rev, allow 20% to 130%, check every 12.0mm, version 3, mag 131 agc 70, measured sensitivity 27.91mm/rev, min 28% max 113% over 13183.3mm(From M122report)
=== Filament sensors ===
Extruder 0: pos 350.16, errs: frame 16 parity 0 ovrun 0 pol 2 ovdue 0**
The above was taken after reloading filament this AM.Note the agc has climbed to 70 while the mag has continued to fluctuate from 130 to 132. AGC usually stands for automatic gain control and my assumption of the mag number has to do with magnetic strength, but I'm just guessing. The need for a sensitivity setting I still find remarkable, but again assuming, it is probably due to reading a magnetic rotation instead of having a direct drive.
The monitor did save my job by detecting a very slight blockage in the nozzle, noted by the tell tail curving of the filament as it is extruded. The min reported was 19%. It also properly paused the job when the filament ran out.
My big takeaway from this job is Not All Filaments are Monitored Equally. Wood filament is a strange animal anyway. I have two more runs of this job to go on this printer and I am anxious to move on to some peg jobs to see how that goes.
All in all I am very satisfied with this monitor. It would be great to have the report to include the current measured percentage. This would allow one to note the current trend. A means of distinguishing a monitor pause from a button pause would also be a fine feature.
Like any other new trick, it just takes some training to get the dog to rollover and speak.
-
@DarylMcM said in Problem with Magnetic Sensor:
Note the agc has climbed to 70 while the mag has continued to fluctuate from 130 to 132. AGC usually stands for automatic gain control and my assumption of the mag number has to do with magnetic strength, but I'm just guessing.
That's correct. The 'mag' value is after agc is applied, so will always be around the same value until the gain runs out (indicated by agc=128 which is its maximum value). So it is the agc value that gives a better indication of magnetic field strength, lower values = higher strength.
To get good readings, it is critical that when the extruder retracts filament, the filament gets pushed back through the filament monitor and turns it backwards. This is best achieved by keeping the filament path between the filament monitor and extruder drive very short and straight, and constraining the filament in that region in PTFE tubing which is only just large enough for the filament,
-
dc42, I do have a minimal distance between the monitor and the extruder entrance. About 3mm. I do not have PTFE in that small area. I do have PTFE restraining the filament from the reel to the entrance of the monitor keeping it straight.
Does the 'A' parameter of the M591 entry need to be set in order for the retractions to be Taken into account? -
@DarylMcM said in Problem with Magnetic Sensor:
Does the 'A' parameter of the M591 entry need to be set in order for the retractions to be Taken into account?
No. The default is A0 which means that actual/commanded movement will only be compared during normal printing moves, not retraction or re-prime moves. You can try A1 if you like, but it will probably give worse results.
-
I seem to be having a simmer issue. I installed the mag sensor about a week ago recently purchased from Filastruder as well. It was working okfor a couple of prints then all of a sudden it started overrunning the set parameters of R60:130 L24.8 E3.0. When I swapped out the filament to Ninja Flex ( a very soft TPU) I stated seeing under runs of ~ 30 to 35%. I adjusted the "R" value accordingly and the remainder of the TPU prints finished off ok. I then swapped out my .04 nozzle for a .8mm nozzle with PLA+ and things went south. I'm now seeing under runs down to 10% and over runs up to 330% My last print was like so:
Duet3D rotating magnet filament monitor v2 on input 3, enabled, sensitivity 25.05mm/rev, allow 10% to 370%, check every 3.0mm, current pos 259.8, measured sensitivity 25.27mm/rev, min 94% max 179% over 9348.6mm
I replaced the the cable between the sensor the E1 stop input with a twister trio to cancel out any interference but this did not make any difference.
My diag output:
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917DA-G4MSJ-6JTF0-3S86M-T9NMA
Used output buffers: 1 of 24 (12 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 94232 of which 16 recycled
Exception stack ram used: 540
Never used ram: 10604
Tasks: NETWORK(ready,524) HEAT(blocked,1236) MAIN(running,1668) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 01:22:56 ago, cause: software
Last software reset at 2019-11-18 13:58, reason: User, spinning module GCodes, available RAM 10652 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 12.1ms, max retries 0
MCU temperature: min 28.5, current 29.3, max 31.9
Supply voltage: min 23.9, current 24.3, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/1023
Driver 1: standstill, SG min/max 0/1023
Driver 2: standstill, SG min/max 0/117
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max 0/107
Date/time: 2019-11-18 15:21:31
Cache data hit count 4294967295
Slowest loop: 59.42ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 169, MinFreeDm: 121, MaxWait: 1366776ms
Bed compensation in use: mesh, comp offset 0.373
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.1
Heater 1 is on, I-accum = 0.6
=== GCodes ===
Segments left: 0
Stack records: 3 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 25.93ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address ec:fa:bc:01:e0:39
WiFi Vcc 3.32, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25464
WiFi IP address 192.168.1.19
WiFi signal strength -53dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0: pos 250.31, ok, measured sens 25.28mm/rev min 94% max 179% over 10057.0mm, errs: frame 0 parity 0 ovrun 0 pol 0 ovdue 0
3:06:28 PMFinished printing file 0:/gcodes/rEX.gcode, print time was 0h 46m
- WiFi -
-
I just purchased a filament sensor from Filastruder and set it up. My mount is not ideal according to the directions because I do not want to mount the sensor on top of the bondtech extruder that is set up as a direct drive on a Railcore. This would add a lot of moving weight. So the sensor is mounted outside the printer and there is a long ptfe tube between the sensor output and the bondtech. I was able to run 3-4 12 hour prints without issue. Now though the sensor stops and says not enough movement was detected.
Is there a way to configure the sensor to simply detect any movement over x amount of time and not try to exactly sync the movements to the print? Should I be using the switch and the magnet sensor? I tried opening up the tolerance to work over a wide range but that did not help.
Settings:
Duet3D magnetic filament monitor on input 3, enabled, sensitivity 24.70mm/rev, allow 20% to 250%, check every 3.0mm, version 2, measured sensitivity 24.82mm/rev, min 91% max 105% over 160.8mmIf you need additional information please let me know.
-
@RandyL said in Problem with Magnetic Sensor:
I then swapped out my .04 nozzle for a .8mm nozzle with PLA+ and things went south. I'm now seeing under runs down to 10% and over runs up to 330% My last print was like so:
Duet3D rotating magnet filament monitor v2 on input 3, enabled, sensitivity 25.05mm/rev, allow 10% to 370%, check every 3.0mm, current pos 259.8, measured sensitivity 25.27mm/rev, min 94% max 179% over 9348.6mm-
How close to the extruder drive inlet is the filament monitor? It needs to be very close, especially for soft filaments such as TPU. Otherwise, when the extruder retracts filament, the filament will try to bunch up in the space between the extruder inlet and the filament monitor, instead of retracting through the filament monitor.
-
A 0.8mm nozzle has four times the filament flow of a 0.4mm nozzle. To get comparable performance from the filament monitor, you should increase the measurement length in proportion. So try 12mm instead of 3mm.
-
-
@ciaossu said in Problem with Magnetic Sensor:
I just purchased a filament sensor from Filastruder and set it up. My mount is not ideal according to the directions because I do not want to mount the sensor on top of the bondtech extruder that is set up as a direct drive on a Railcore. This would add a lot of moving weight. So the sensor is mounted outside the printer and there is a long ptfe tube between the sensor output and the bondtech.
That is not going to work well, because filament will bunch up in the tube when retraction occurs..
Is there a way to configure the sensor to simply detect any movement over x amount of time and not try to exactly sync the movements to the print? Should I be using the switch and the magnet sensor? I tried opening up the tolerance to work over a wide range but that did not help.
You still have the measurement distance set to 3.0mm. Try a larger amount.
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
Hi, a quick update from me. Duet replaced my sensor (kudos to @Roland, the swap was quick and flawless, even if I live in Singapore).
I have been using the new sensor for several weeks now, and it has saved many prints, and potentially more disastrous situations. The sensor never paused the printer without a valid reason: clogged nozzle, empty spool, and once the spool even fell to the floor.
Great tool, highly recommended.
-
@taglia thanks for the update
-
Thanks for the advice. I will try increasing the measurement length as you suggest. My sensor is mounted ~20mm above a direct drive extruder and was flexing around a lot. I added a brace which helped a lot but am still having issue. I will try increasing the measurement length as you suggest.
