Duet 2 wifi Mesh compensation

droftarts

@Runar What firmware version are you running? Send M115 in the DWC console and post response.

You shouldn't need the second G29 S1; G29 on it's own will probe the bed, save the height map in a file on the SD card, and activate bed compensation. You can check this by sending M408 S3, which shows the compensation in use in the report:

M408 S3
{"status":"P","coords":{"axesHomed":[1,1,1],"wpl":1,"xyz":[-3.868,-17.534,10.900],"machine":[-13.108,-27.845,10.850],"extr":[556.4]},"speeds":{"requested":15.0,"top":15.0},"currentTool":0,"params":{"atxPower":0,"fanPercent":[100,100,0,0,0,0,0,0,0],"fanNames":["","","","","","","","",""],"speedFactor":100.0,"extrFactors":[100.0],"babystep":-0.050},"sensors":{"probeValue":0,"fanRPM":0},"temps":{"bed":{"current":60.4,"active":60.0,"standby":0.0,"state":2,"heater":0},"current":[60.4,184.9,2000.0,2000.0,2000.0,2000.0,2000.0,2000.0],"state":[2,2,0,0,0,0,0,0],"names":["","","","","","","",""],"tools":{"active":[[185.0]],"standby":[[190.0]]},"extra":[{"name":"*MCU","temp":32.7}]},"time":7606.0,"coldExtrudeTemp":160.0,"coldRetractTemp":90.0,"compensation":"None","controllableFans":1,"tempLimit":290.0,"endstops":4088,"firmwareName":"RepRapFirmware for Duet 2 WiFi/Ethernet","geometry":"cartesian","axes":3,"totalAxes":3,"axisNames":"XYZ","volumes":2,"mountedVolumes":1,"name":"CartesIan","probe":{"threshold":500,"height":1.25,"type":1},"tools":[{"number":0,"heaters":[1],"drives":[0],"axisMap":[[0],[1]],"fans":1,"filament":"","offsets":[0.00,0.00,0.00]}],"mcutemp":{"min":13.3,"cur":32.7,"max":33.1},"vin":{"min":11.4,"cur":12.0,"max":12.4}}

You can send M408 S3 while printing to check (I just did!)

Ian

Runar

Okay, thanks I try when I get home. Stupid question though, you say "save the height map in a file on the SD card" I do not use any SD card my heightmap.csv is in folder / sys. Is there a difference?

My Firmware 2,04

aidar

Ian means G29 saves the height map in file on SD card. And yes, you have SD card in Duet, the / sys folder is on it. Without SD card Duet will not work, assuming its Duet2 (wifi, ethernet or maestro, doesnt matter)

Runar

@aidar said in Duet 2 wifi Mesh compensation:

Ian means G29 saves the height map in file on SD card. And yes, you have SD card in Duet, the / sys folder is on it. Without SD card Duet will not work, assuming its Duet2 (wifi, ethernet or maestro, doesnt matter)

Thank you all, now I understand. I will check everything when I´m at home.

/Runar

Phaedrux

@droftarts said in Duet 2 wifi Mesh compensation:

M408 S3

You can also see if compensation is active in the results of M122

gtj0

Make sure your Z "jerk" (M566) isn't set too low, if it is, the motors may not move at all.

Phaedrux

@gtj0 said in Duet 2 wifi Mesh compensation:

Make sure your Z "jerk" (M566) isn't set too low, if it is, the motors may not move at all.

If the Z zerk is too low the Z motors will still move, but the X and Y may pause to give the Z axis time to finish the move, resulting in jerky movement.

gtj0

@Phaedrux said in Duet 2 wifi Mesh compensation:

@gtj0 said in Duet 2 wifi Mesh compensation:

Make sure your Z "jerk" (M566) isn't set too low, if it is, the motors may not move at all.

If the Z zerk is too low the Z motors will still move, but the X and Y may pause to give the Z axis time to finish the move, resulting in jerky movement.

You know, I thought I was speaking from experience...
https://forum.duet3d.com/topic/13423/can-anyone-else-confirm-these-z-behaviors-with-3-0rc1?_=1576942676499

But I'll be damned if I can replicate my findings now.

Phaedrux

@gtj0 I can't speak to any variation between 2.x behaviour and 3.x behaviour.

gtj0

@Phaedrux said in Duet 2 wifi Mesh compensation:

@gtj0 I can't speak to any variation between 2.x behaviour and 3.x behaviour.

Thanks for confirming my worst nightmare... it's just me.

Graham

Used this to solve my issue with my Predator upgrade. Set Z jerk to 1500 and poof, problem solved.