Help: Temp Sensors and Homing Issues

Danal

@dc42 said in Help: Temp Sensors and Homing Issues:

@Danal said in Help: Temp Sensors and Homing Issues:

AND, your homeall.g is completely wrong. It should be:

G91 G1 Z5 F800 H2 ; Lift z so we don't crash
M98 P"homey.g"
M98 P"homex.g"
M98 P"homez.g"

And nothing else.

That's one way to do homeall.g, but not the only one. The point of having homeall.g is that you can take some shortcuts when you know you are homing all the axes. For example, you can lift Z only once, and on Cartesian and CoreXY machines you can home X and Y simultaneously.

When debugging homing, it's best to debug homing each axis separately, X and Y before Z. When they are working individually, move on to home all 3 with a single G28 command.

Agreed. I probably should have said "a more clear way for debugging" instead of "completely wrong"...

94118

Now i need help with the temp sensors:

As you know my hotend is a mk10 with K Type Thermistor that screws into block Currently show NO Read
I have tried everything i can to get this fixed and cannot get it to sense. (i.e Jumper wire between both terminals of the K Type Daughter board, wired in fuse to VSSA e1 and e0 Ground daughter board shows no fault via leds. been trying to get the firmware to talk to the daughter board and are having no luck current status shows NA.

Second i have a 24v 180W Silicone heat pad for the bed from keenovo they use the NTC100K thermistor however i cannot get this read correctly (current status is -273)

my paneldue shows no read or 0 for both bed and hotend

94118

console.txt

my hotend heater comes up with this code:

GPIO/servo pin1 NO Pin

Phaedrux

It looks like you updated to reprapfirmware 3 without updating your config.g. Substantial changes are required for RRF3.

You'll need to either redo your config files using the online configurator tool, or revert to 2.05.

I think it would be best to stick with 2.05 until you have everything working before making the jump to RRF3.

94118

Reflashed entire firmware to 2.05 cannot home my axis, Hotend thermistor still does not read as well as my bed still states -273 their is NO Shorts or loose wires with either of them.

94118

[0_1581127980987_config.zip](Uploading 100%) here is a copy of my current config files. i need to control these files like simplfy 3d with my Flashforge creator (i.e. X to home right, Y to Home Back, and Z to raise the bed)

Phaedrux

zip files won't work. just copy and paste the contents.

94118

I did do a copy and paste:
z is grinding when in the home position which is Raised to 0. any news about fixing my temp sensors

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

I did do a copy and paste:

Copy and paste the contents of the files into a forum post.

You've uploaded them earlier. Have they changed since then?

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

any news about fixing my temp sensors

The issues presented seem like wiring issues. Are you using extension cables at all? Are the crimps good?

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

z is grinding when in the home position which is Raised to 0

I'm not sure what that means. Raised by 0.

94118

my z axis is at the top of the printer hitting my z endstop and loud grinding this happens every time i home the z and have to trigger an emergency stop and reset. Wiring is solid All Crimps and Ferrells i can send a current pict.(https://drive.google.com/open?id=1C2ZJ8UMBzF1jl2yiAGesEVCoj4MjkdAC)

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

my z axis is at the top of the printer hitting my z endstop and loud grinding this happens every time i home the z

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Thu Feb 06 2020 14:52:27 GMT-0800 (Pacific Standard Time)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position

At the start of the homing files there is usually a Z move to lift the Z axis to get it out of the way for travel. perhaps this is what's running it into the endstop?

But if that's the case, then I think you have the direction of the Z motor incorrect, because that Z move should be moving the bed AWAY from the endstop, not into it.

94118

okay i just changed the direction of the drive from backward to forward in the

config.g

94118

BTW does anyone know how to wire an RGBW Led Strip to a duet

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

okay i just changed the direction of the drive from backward to forward in the

config.g

And did that fix it?

M126 S[fan_speed_pwm]
M140 S[bed0_temperature] P0
M134 P0                                 ; stabilize bed temperature
M104 S[extruder0_temperature] H1
M133 H1                                 ; stabilize extruder temperature
G130 X127 Y127 Z40 A127 B127            ; default stepper Vrefs A0 ; zero extruder
G1 Z0.4                                 ; position nozzle
G1 E25 F300                             ; purge nozzle
G1 X-115 Y-65 Z0.15 F1200               ; slow wipe
G1 X-110 Y-60 Z0.5 F1200                ; lift
G92 A0                                  ; zero extruder

Do you actually have all that as part of your config.g?

94118

@94118 said in Help: Temp Sensors and Homing Issues:

Yes it is part of the Priming and Purge code for the hotend when it was on my FFC

94118

it was running Sailfish on a mightyboard and it worked

Phaedrux

Some of those gcodes aren't supported in reprapfirmware. (M134, M133, G130) And the extruder in RRF is E, not A and B.

It would be best practice to not have heating and axis movement commands in config.g since it is executed at startup.

94118

ok i will rework the config.g file