Hotend and Heated bed reading 2000deg celcius and fault

NEVER LUCKY

im really lost here. what should i do?

droftarts

@NEVER-LUCKY Yes, you're using a config.g file for RRF3, but your board has RRF 2.05.1. The first line of your config.g is ; Configuration file for Duet Maestro (firmware version 3) So the config tool does tell you what firmware version it's for.

Is this a new board, or was it working before? If this is a new install, either:

If you have the config.json file you used to generate your current config.g, go to the RRF config tool and load it. Then, on the 'General' tab, change the firmware version from '3.0 or later' to '2.03 to 2.05'. Then go through and check that it's set up correctly, export config.g, and try that.

Or

Update your Maestro to RepRapFirmware 3 (which is going to be the future of the firmware) and sort out config.g issues there.

If it was working before, revert to the config.g you were using.

Ian

NEVER LUCKY

@droftarts said in Hotend and Heated bed reading 2000deg celcius and fault:

RRF config tool

oh nice. its doing fine now.
however im getting new errors: the hotend doesnt heat up and is at -273,1 and the bed gets the error for heating up slowly.

droftarts

@NEVER-LUCKY Which did you do, update to RRF 3, or generate new config.g? If new config.g, post it. Please post the whole config.g, as text, in the 'code' tags, using </> from the formatting bar.

-273 means that the thermistor is not connected. Probably you have defined it for the wrong pins.

Ian

NEVER LUCKY

i updated the firmware to 3.0.

; Configuration file for Duet Maestro (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Jan 18 2020 15:59:57 GMT+0100 (Central European Standard Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Colossus"                                   ; set printer name
M665 R154 L324 B150 H700                           ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0                                      ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 P0.0.0.0 S1                                   ; enable network and acquire dynamic address via DHCP
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E663.00                   ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00           ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00        ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00           ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30                    ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 Z0 S1                                         ; set minimum Z

; Endstops
M574 X2 S1 P"xstop"                                ; configure active-low endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop"                                ; configure active-low endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop"                                ; configure active-low endstop for high end on Z via pin zstop

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 R85 S20                                       ; define mesh grid

; Heaters


M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S130                                       ; set temperature limit for heater 0 to 130C
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit

; Tools
M563 P0 S"Extruder_TOOL" D0 H1 F0                  ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

NEVER LUCKY

i didnt change a thing in the config and didnt generate a new one. only the RRF is 3.0 now

droftarts

@NEVER-LUCKY Okay. Hot end thermistor should be on e0temp, the right-hand two-pin connection here:

If it is, can you test the wiring with a multimeter? If not, try swapping bed and hot end thermistors connections, see if you get a reading for the hot end thermistor on the bed.

Ian

NEVER LUCKY

alright! its all fine the wiring was wrong... so dumb of me!

the bed heater is still fault for rising slowly though.

droftarts

@NEVER-LUCKY You'll need to tune the bed with M303. RRF3 doesn't assume that any heater is a bed, so it just thinks something is wrong.

First, you need to get your temperature sensors reporting accurately. You're using:

M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp

T100000 B4138 is the default thermistor setting, for a Honeywell 135-104QAD-J01 thermistor that shipped with hot ends from RepRapPro, who have been out of business for 4 years! So I doubt you have the correct thermistor settings, and likely the temperature your heaters are reporting is not accurate. All 100k ohm thermistors have a resistance of 100k ohms at 25C, and will be fairly accurate at room temperature, but they report very differently as they get hotter. So please check what thermistors you have in your bed and hot end, and set them correctly, then you have a chance of accurately setting extrusion temperature.

Then, your heater settings. For full details see: https://duet3d.dozuki.com/Wiki/Tuning_the_heater_temperature_control

Your heater settings are at the default. It looks like you haven't tuned your heaters THEN sent M500 (to store them to config-override.g). Alternatively you can copy the heater tuning to config.g. This hasn't been done, as the heater profiles in your config.g are still:

M307 H0 B0 S1.00
M307 H1 B0 S1.00

While the hot end will probably heat up, the temperature control won't be smooth. So, tune heaters with something like:

M303 H0 S60
M303 H1 S200

Run them each a number of times (usually three times will do), but wait for the heater to be at room temperature before doing it again. Once the results converge, send M500 to save them to config-override.g

Then either add M501 to the end of config.g so they load from config-override.g, or copy the heater settings to config.g

You can check the current heater settings by sending M307 H0 or M307 H1 from the console.

Ian

NEVER LUCKY

thanks for the tips!!
so now im doing the tuning by sending the commands from above, ill do it 3 times as you said, but where exactly must i add M501 in config.g ?
at the last line of ;Heaters or the last line of config.g ?

droftarts

@NEVER-LUCKY
Either add M501 to the end of config.g so they load from config-override.g, or copy the heater settings (M308 for bed and hot end) to config.g (from config_override.g to config.g)

Ian

NEVER LUCKY

right. and should i send M500 after i tune the bed and then tune the hotend and send M500 again? Or can i tune the bed and hotend both 3 times and afterwards sent M500 once ?

Phaedrux

@NEVER-LUCKY Send M500 after each. I'm not sure if the tunes values are applied immediately after tuning, or if they need to be saved and loaded by a reboot. Actually, you don't even have to reboot. Save with M500 which saves the values to config-override.g and then send M501, which loads config-override.g.

For what it's worth I've only ever run the tuning once. IF you do run it multiple times, don't forget to let it reach room temp before starting again.

NEVER LUCKY

for some reason my hotend fans stopped spinning. should i tune the hotend without fans?
im not sure what the problem is, the two fans stopped spinning last night, but when i click on TestFans, they do just fine and start spinning and after the test they go off.

Phaedrux

@NEVER-LUCKY said in Hotend and Heated bed reading 2000deg celcius and fault:

should i tune the hotend without fans?

No.

What do you have in your config.g for fans? How are the fans wired?

Phaedrux

@NEVER-LUCKY said in Hotend and Heated bed reading 2000deg celcius and fault:

TestFans,

Test fans sounds like a factory test macro. Do not use it.

Does the hotend fan spin briefly at power on?

NEVER LUCKY

They are wired fine because TestFans Macro runs perfectly but after that they turn off completely and there is no way to turn even on of the two on. Im using an alwaysOn fan aswell to cool the drivers and that is running just fine. only the two hotend fans are not spinning.

; Configuration file for Duet Maestro (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Jan 18 2020 15:59:57 GMT+0100 (Central European Standard Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Colossus"                                   ; set printer name
M665 R154 L324 B150 H700                           ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0                                      ; put your endstop adjustments here, or let auto calibration find them

; Network
M552 P0.0.0.0 S1                                   ; enable network and acquire dynamic address via DHCP
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S1                                         ; physical drive 0 goes forwards
M569 P1 S1                                         ; physical drive 1 goes forwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E663.00                   ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00           ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00        ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00           ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E800 I30                    ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 Z0 S1                                         ; set minimum Z

; Endstops
M574 X2 S1 P"xstop"                                ; configure active-low endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop"                                ; configure active-low endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop"                                ; configure active-low endstop for high end on Z via pin zstop

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 R85 S20                                       ; define mesh grid

; Heaters


M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M143 H0 S130                                       ; set temperature limit for heater 0 to 130C
M307 H0 B1 S1.00                                   ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit

; Tools
M563 P0 S"Extruder_TOOL" D0 H1 F0                  ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

NEVER LUCKY

i cant find a thing about fans in config

NEVER LUCKY

@Phaedrux said in Hotend and Heated bed reading 2000deg celcius and fault:

Test fans sounds like a factory test macro. Do not use it.

at power on neither of the two spin

Phaedrux

Ok, I'm guessing you didn't choose any fans when running the configurator.

How do you have the fans connected?

You said that when you ran TESTFANS the fans would spin?
Can you post the contents of that macro?