Help: Temp Sensors and Homing Issues

dc42

If it says Connecting, the PanelDue firmware is almost certainly OK.

Go to the Setup page on PanelDue, check the baud rate setting there is 57600
Connect to the Duet via YAT or DWC and send M575 P1. Check that it also reports 57600 baud.

94118

Here is the results:
console.txt and this after i checked that the board and the panel are on the same baud speed setting. how would i issue a restart or reset of the board and panel.

dc42

Your M575 P1 setting is correct, so it should be able to communicate with the PanelDue assuming that the PanelDue is set to 57600 in the Settings page.

Next step is to check whether the Duet is receiving data form PanelDue. Connect to the Duiet via YAT and send M111 S1 P3. It should report that debugging enabled for the GCodes module. It will then echo all received GCode commands in the YAT main window. Do you see any messages beginning "aux: M408" ? You should get those as long as the PanelDue is not on the Setup page.

If you are using the ribbon cable, make sure it is plugged into the CONN_SD socket on the Duet. Not CONN_LCD.

94118

Here is the result from DWC YAT is not giving me connection options for comm ports. YAT is to difficult
console.txt

Phaedrux

@94118 said in Help: Temp Sensors and Homing Issues:

YAT is to difficult
console.txt

M111 S1 P3 has enabled debugging messages to steam to the USB port. You will need either YAT or some other USB terminal to view it.

94118

having problems with USB terminal emulators they do not see anything beyond comm 1

Phaedrux

Does the duet show up as a device in device manager?

94118

NO it does not

Phaedrux

But you are able to connect to the duet via the network and DWC?

Phaedrux

When you connect the Duet via USB does it make the usb device detected sound?

Phaedrux

Have you followed this part of the getting connected guide?
Have you installed the drivers?
It also covers YAT.

https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7#s5

94118

Duet to the network Yes. Duet to USB NO Sound from windows. Unable to install duet drivers cause DM states not compatible with 64bit

94118

Request an update for recent message about the paneldue

94118

Duet 2 wifi seems to good with USB but not the paneldue

Phaedrux

Please see the post from DC42 above. https://forum.duet3d.com/post/134957

You need YAT connected via USB so that we can see if there is communication between the paneldue and the duet.

94118

Direct from YAT: with Duet 2 plugged in to USB talking to Paneldue

Debugging enabled for modules: GCodes(3)<LF>Debugging disabled for modules: Platform(0) Network(1) Webserver(2) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13) WiFi(14) Display(15) LinuxInterface(16)<LF>

NO (aux: M408)

What next

Phaedrux

dc42 said in Help: Temp Sensors and Homing Issues:

If you are using the ribbon cable, make sure it is plugged into the CONN_SD socket on the Duet. Not CONN_LCD.

In your first picture it shows the PanelDue ribbon cable plugged into the wrong port. Are you still connected that way? Have you tried the 4 wire cabling option?

https://duet3d.dozuki.com/Wiki/Duet_Wiring_Diagrams

94118

disconnected ribbon cable now it shows Idle And Temps

Phaedrux

So it's working now? Your responses are so short it's hard to know what's actually going on, which makes it very challenging to help you out.

94118

I have and got it working by removing the ribbon cable. Now i think its my endstops conflicting with homing controls and commands (https://drive.google.com/open?id=1DxrsV36-5PN991DjbJJKdIKGP0n85crk) picture included status of endstops state Yes