Release 3.01-RC10

sebkritikel

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Thu Apr 23 2020 22:39:29 GMT+0200 (Ora legale dell’Europa centrale)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
M913 X50 Y50 ; Riduci la corrente al 50%
G1 H1 X-9999 Y-9999 F4000 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-9999 ; home X axis
G1 H1 Y-9999 ; home Y axis
G1 X5 Y5 F2000 ; go back a few mm
G1 H1 X-9999 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-9999 ; then move slowly to Y axis endstop
G90 ; absolute positioning
G1 X60 Y50 F9000 ; go to first bed probe point and home Z
M913 X100 Y100 :Riporta la corrente al 100%
G30 ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z10 F100 ; lift Z relative to current position
;G90 ; absolute positioning

Can you try:

;homeall.g
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position

;;;M913 X50 Y50 ; Riduci la corrente al 50%

G1 H1 X-9999 Y-9999 F4000 ; move quickly to X or Y endstop and stop there (first pass)

G1 X5 Y5 F2000 ; go back a few mm

G1 H1 X-9999 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-9999 F360 ; then move slowly to Y axis endstop

G90 ; absolute positioning

G1 X60 Y50 F9000 ; go to first bed probe point and home Z

;;;M913 X100 Y100 :Riporta la corrente al 100%

G30 ; home Z by probing the bed

Leblond

@sebkritikel ok now i try

Leblond

@sebkritikel said in Release 3.01-RC10:

;homeall.g G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position ;;;M913 X50 Y50 ; Riduci la corrente al 50% G1 H1 X-9999 Y-9999 F4000 ; move quickly to X or Y endstop and stop there (first pass) G1 X5 Y5 F2000 ; go back a few mm G1 H1 X-9999 F360 ; move slowly to X axis endstop once more (second pass) G1 H1 Y-9999 F360 ; then move slowly to Y axis endstop G90 ; absolute positioning G1 X60 Y50 F9000 ; go to first bed probe point and home Z ;;;M913 X100 Y100 :Riporta la corrente al 100% G30 ; home Z by probing the bed
91/5000

wait because it gives me an error "6/5/2020, 18:12:41 G28
Error: G0 / G1: insufficient axes homed "

sebkritikel

This post is deleted!

sebkritikel

@Leblond said in Release 3.01-RC10:

@sebkritikel said in Release 3.01-RC10:

;homeall.g G91 ; relative positioning G1 H2 Z5 F6000 ; lift Z relative to current position ;;;M913 X50 Y50 ; Riduci la corrente al 50% G1 H1 X-9999 Y-9999 F4000 ; move quickly to X or Y endstop and stop there (first pass) G1 X5 Y5 F2000 ; go back a few mm G1 H1 X-9999 F360 ; move slowly to X axis endstop once more (second pass) G1 H1 Y-9999 F360 ; then move slowly to Y axis endstop G90 ; absolute positioning G1 X60 Y50 F9000 ; go to first bed probe point and home Z ;;;M913 X100 Y100 :Riporta la corrente al 100% G30 ; home Z by probing the bed
91/5000

wait because it gives me an error "6/5/2020, 18:12:41 G28
Error: G0 / G1: insufficient axes homed "

Ok maybe my mistake. Please try:

;homeall.g
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position

;;;M913 X50 Y50 ; Riduci la corrente al 50%

G1 H1 X-9999 Y-9999 F4000 ; move quickly to X or Y endstop and stop there (first pass)

G1 H1 X-9999 ; home X axis
G1 H1 Y-9999 ; home Y axis

G1 X5 Y5 F2000 ; go back a few mm

G1 H1 X-9999 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-9999 F360; then move slowly to Y axis endstop

G90 ; absolute positioning

G1 X60 Y50 F9000 ; go to first bed probe point and home Z

;;;M913 X100 Y100 :Riporta la corrente al 100%

G30 ; home Z by probing the bed

Leblond

This post is deleted!

Leblond

@sebkritikel there was a small error, so it works:

; homeall.g
G91; relative positioning
G1 H2 Z5 F6000; lift Z relative to current position
; M913 X50 Y50; Reduce the current to 50%
G1 H1 X-9999 F4000
G1 H1 Y-9999; move quickly to X or Y endstop and stop there (first pass)
G1 X5 Y5 F2000; go back a few mm
G1 H1 X-9999 F360
G1 H1 Y-9999; move slowly to X axis endstop once more (second pass)
G90; absolute positioning
G1 X60 Y50 F9000; go to first bed probe point and home Z
; M913 X100 Y100: Returns the current to 100%
G30; home Z by probing the bed

Change something for you?

Leblond

by the test I mean

sebkritikel

@Leblond said in Release 3.01-RC10:

@sebkritikel there was a small error, so it works:

; homeall.g
G91; relative positioning
G1 H2 Z5 F6000; lift Z relative to current position
; M913 X50 Y50; Reduce the current to 50%
G1 H1 X-9999 F4000
G1 H1 Y-9999; move quickly to X or Y endstop and stop there (first pass)
G1 X5 Y5 F2000; go back a few mm
G1 H1 X-9999 F360
G1 H1 Y-9999; move slowly to X axis endstop once more (second pass)
G90; absolute positioning
G1 X60 Y50 F9000; go to first bed probe point and home Z
; M913 X100 Y100: Returns the current to 100%
G30; home Z by probing the bed

Change something for you?

I think I made a mistake. I am not a CoreXY expert Sorry!

So does:

; homeall.g
G91; relative positioning
G1 H2 Z5 F6000; lift Z relative to current position
; M913 X50 Y50; Reduce the current to 50%
G1 H1 X-9999 F4000
G1 H1 Y-9999; move quickly to X or Y endstop and stop there (first pass)
G1 X5 Y5 F2000; go back a few mm
G1 H1 X-9999 F360
G1 H1 Y-9999; move slowly to X axis endstop once more (second pass)
G90; absolute positioning
G1 X60 Y50 F9000; go to first bed probe point and home Z
; M913 X100 Y100: Returns the current to 100%
G30; home Z by probing the bed

Work ok?

Leblond

@sebkritikel quello che ho corretto io funziona bene
ho provato e l'estrusore funziona bene

Leblond

@sebkritikel thank you so much my friend

Leblond

so does the M913 command make a mess?

sebkritikel

@Leblond said in Release 3.01-RC10:

@sebkritikel thank you so much my friend
Happy to help!

@Leblond said in Release 3.01-RC10:

so does the M913 command make a mess?

I do not know. Can you test this:

; homeall.g
G91; relative positioning
G1 H2 Z5 F6000; lift Z relative to current position
M913 X50 Y50; Reduce the current to 50%
G1 H1 X-9999 F4000
G1 H1 Y-9999; move quickly to X or Y endstop and stop there (first pass)
G1 X5 Y5 F2000; go back a few mm
G1 H1 X-9999 F360
G1 H1 Y-9999; move slowly to X axis endstop once more (second pass)
G90; absolute positioning
G1 X60 Y50 F9000; go to first bed probe point and home Z
M913 X100 Y100: Returns the current to 100%
G30; home Z by probing the bed

with M913

Leblond

@sebkritikel ok wait for it to load

Leblond

no it doesn't work that way

Leblond

with the command M913 inserted it does not work

sebkritikel

@sebkritikel said in Release 3.01-RC10:

@Leblond said in Release 3.01-RC10:

@sebkritikel thank you so much my friend
Happy to help!

@Leblond said in Release 3.01-RC10:

so does the M913 command make a mess?

I do not know. Can you test this:

; homeall.g
G91; relative positioning
G1 H2 Z5 F6000; lift Z relative to current position
M913 X50 Y50; Reduce the current to 50%
G1 H1 X-9999 F4000
G1 H1 Y-9999; move quickly to X or Y endstop and stop there (first pass)
G1 X5 Y5 F2000; go back a few mm
G1 H1 X-9999 F360
G1 H1 Y-9999; move slowly to X axis endstop once more (second pass)
G90; absolute positioning
G1 X60 Y50 F9000; go to first bed probe point and home Z
M913 X100 Y100: Returns the current to 100%
G30; home Z by probing the bed

with M913

@Leblond said in Release 3.01-RC10:

with the command M913 inserted it does not work

Ok, I do not know why. @dc42 to me it looks like its narrowed down to M913. I do not use this command, so unfortunately I do not have any insight.

Leblond

no problem, I don't wear it and I'm happy like this

Leblond

maybe it can depend on which position it is inserted ..

Leblond

however it does it only and exclusively in the homeall.g file, because in other files I have inserted it and it works well