CR 10 5s

Thunder

sorry here is it :

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Fri May 01 2020 16:13:33 GMT+0200 (Srednjeevropski poletni čas)

; General preferences
G90                                     ; send absolute coordinates...
M83                                     ; ...but relative extruder moves
M550 P"CR10 5S"                         ; set printer name
M918 P1 E4 F2000000                     ; configure direct-connect display

; Network

; Drives
M569 P0 S0                              ; physical drive 0 goes backwards
M569 P1 S0                              ; physical drive 1 goes backwards
M569 P2 S1                              ; physical drive 2 goes forwards
M569 P3 S0                              ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                        ; set drive mapping
M350 X32 Y32 Z32 I0                     ; configure microstepping without interpolation
M350 E16 I1                             ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 E420.00      ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00     ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00     ; set accelerations (mm/s^2)
M906 X1680 Y1680 Z1680 E800 I50         ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                        ; set axis minima
M208 X500 Y500 Z500 S0                  ; set axis maxima

; Endstops
M574 Z1 S0                              ; set active low and disabled endstops
M574 X1 Y1 S1                           ; set active high endstops

; Z-Probe
M558 P0 H5 F120 T24000                  ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                ; define mesh grid

; Heaters
M305 P0 T100000 B4092 R4700             ; set thermistor + ADC parameters for heater 0
M143 H0 S150                            ; set temperature limit for heater 0 to 150C
M305 P1 T100000 B4092 R4700             ; set thermistor + ADC parameters for heater 1
M143 H1 S275                            ; set temperature limit for heater 1 to 275C

; Fans
M106 P0 S0 I0 F500 H-1                  ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45               ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1:0 T45             ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                        ; define tool 0
G10 P0 X0 Y0 Z0                         ; set tool 0 axis offsets
G10 P0 R0 S0                            ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

Thanks

NitroFreak

You have a 400 steps/rev stepper, the original are 200. You need to double your steps/mm for every axis that you switched the steppers out

PaulHew

@Thunder said in [CR 10 5s]
Did you use the RRF Config Tool (Click the link)

My First glance is your M906, some of your values are high.
My suggestion
M906 X1400 Y1700 Z1400 E800 I50 ; set motor currents (mA) and motor idle factor in per cent

I am guessing In regards to your M92, you can try it, I am not saying it is right!
M92 X400 Y200 Z4000.00 E420.00 ; set steps per mm
Make sure if you move 10mm in any axis from DWC it has physically moved that distance,

Also I would start with this, then tweak later.
M350 X16 Y16 Z16 E16 I 0 ; set 16x microstepping for axes & extruder, without interpolation

As I said, not 100%, but it might get you on the right path.

Paul.

Phaedrux

@Thunder said in CR 10 5s:

Z4000.00

4000 steps per mm on the Z axis is unlikely. 400 perhaps?

ziggymanpopo

I did somthing simular to a cr10 s what is the pich on your screw 5 or 10 mm. Kersy manufacturing Has a u tube video that might be very helpful it was for me. He goes thrie the whole process

Thunder

Ok. Long time no write. I have made the printer move. And now I have another problem. I have a titan aero extruder with a Vulcano hotend. And now I struggle with the top layer and the edges. I get a bit deformed left corner.
Hope anybody will see this thread. Z is the top layer

Here is my config file.

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 24 2020 20:05:38 GMT+0200 (Central European Summer Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"My Printer"                                 ; set printer name

; Network
M551 P"GoBevk"                                     ; set password
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S0                                         ; physical drive 0 goes backwards
M569 P1 S0                                         ; physical drive 1 goes backwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X160.00 Y80.00 Z800.00 E809.00                 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1400 Y1700 Z1400 E800 I50                    ; set motor currents (mA) and motor idle factor in per cent
M84 S50                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X500 Y500 Z500 S0                             ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S1                                   ; set active high endstops

; Z-Probe
M307 H3 A-1 C-1 D-1                                ; disable heater on PWM channel for BLTouch
M558 P9 H5 F120 T24000                             ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-66.4 Y-10.2 Z2.15                            ; set Z probe trigger value, offset and trigger height
M557 X15:495 Y15:495 S20                           ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 1
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                             ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

![6_1590644526968_IMG-4002.JPG](Uploading 100%) ![5_1590644526967_IMG-4001.JPG](Uploading 100%) ![4_1590644526967_IMG-3999.JPG](Uploading 100%) ![3_1590644526966_IMG-3998.JPG](Uploading 100%) ![2_1590644526965_IMG-3997.JPG](Uploading 100%) ![1_1590644526965_IMG-3996.JPG](Uploading 100%) ![0_1590644526959_IMG-3995.JPG](Uploading 100%)

Any suggestions ??:)

Thunder

Ok and now the pictures :

https://ibb.co/8MpQxcJ
https://ibb.co/NN1n4zJ
https://ibb.co/q9rRb3G
https://ibb.co/vHDkSY9
https://ibb.co/SnsXfHZ
https://ibb.co/GRvZFQ1
https://ibb.co/1z8SLzX

The nozzle is 0.8mm

ziggymanpopo

You might find it interestin but i put linear rails/ballscrew and with a pich if 10mm if you are interested in knowing the effort was worth it .
all the gosting is gone completely. It was a lot of work please feel free to ask me anything you like
I have not experienced the same issues with my top layers but im only running a .4 nozzle...
Just chainging the board out is enough of a challenge my hats off to you! knowing whats to be done!! i call it the fankenprinter!!!

My next step is to strip the x carrage completely
I thought i would use both an end stop for the z axes and the z probe. I kbow its possable seen a couple of posts
Reasoning behind is after the upgrade there will be no more give on the hotend thus as a safety precaution, i have run my hotend carriage into my build platform several times
Hemera direct drive extrude upgrade to come

ziggymanpopo

By the way its not a cr-10s5 anymore
Same thing i started with.

Thunder

@ziggymanpopo Thanks. I also upgraded the z-axis and the x-axis to linear rails. Still have to upgrade the x-axis. Why did you decide to change the ball screws? Thanks for the compliment :).
What do i call it ?

ziggymanpopo

I nsmed my printer frankenprinter as a joke almost all of the original parts are gone just the frame left
I found out that almost all of my settings needed tweeking after the d.w.c. change
I used the 10 pitch,, much faster ball screw.