Do you mean in the home all section? Sorry I am a little slow when programing

@fcwilt

Yes like the last one, this code is in slicer start program.

@fcwilt

Ok i checked and you are right. In the startup i had a M375 command. I deleted the line and replaced the command with G29 S1. And now my next question if load the g code of a part for printing the machine homes and makes the printer use the height map that i did eariler with G29 S0. But my nozzle is stil a few 0.1 mm from build plate. Do i correct this with baby steps ?

Thanks for all of your input

Ok, I have now managed the calibration. But when I start the program from the slicer I get the Error: M375: Heightmap file bareplate.csv not found I think this means my startup code is not ok

thank you

And here is the picture

Yes, this is right. Ok, came home and started the machine and a couple of settings were wrong. Now I have managed the home all to touch the probe for z and started the G29 S0
but I still get the same result. Can anybody point out what I am doing wrong? I am new to programming and this kind of setup.

System
My Printer
g29 s0
Status
Busy
Tool Position
X
346.4
Y
320.2
Z
7.15
Extruder Drives
Drive 0
0.0
Speeds
Requested Speed
3 mm/s
Top Speed
3 mm/s
Sensors
Vin
12.0 V
MCU Temperature
28.4 C
Fan RPM
0
Z-Probe
0
 Tools
 Extra
 Control All
Tool	Heater	Current	Active	Standby
Tool 0 
T0 - Load Filament	Heater 1 
off	16.9 C	
0
0
Bed	Heater 0 
off	18.2 C	
0
0
Temperature Chart
System Directory
0:/sys/config.g
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 24 2020 20:05:38 GMT+0200 (Central European Summer Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"My Printer"                                 ; set printer name

; Network
M551 P"GoBevk"                                     ; set password
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S0                                         ; physical drive 0 goes backwards
M569 P1 S0                                         ; physical drive 1 goes backwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S1                                         ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X160.00 Y80.00 Z800.00 E837                   ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00                ; set accelerations (mm/s^2)
M906 X1400 Y1700 Z1400 E800 I50                    ; set motor currents (mA) and motor idle factor in per cent
M84 S50                                       ; Set idle timeout

;Bl-touch heaters
M307 H3 A-1 C-1 D-1                                ; disable heater on PWM channel for BLTouch

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X500 Y500 Z500 S0                             ; set axis maxima

; Endstops
M574 X1 Y1 S1;                                   ; set active high endstops
M574 Z1 S2;


; Z-Probe
M558 P9 H5 F500 T4000 X0 Y0 Z1                     ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-66.4 Y-10.2 Z2.15                       ; set Z probe trigger value, offset and trigger height
M557 X70:433.6 Y70:498.8 S30                           ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                        ; set thermistor + ADC parameters for heater 1
M143 H1 S280                                       ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                             ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C



; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2.0.4 on Sun Sep 15 2019 21:01:39 GMT+0200 (Central European Summer Time)
G91 ; relative positioning
G1 Z5 F6000 S2 ; lift Z relative to current position
G1 S1 X-500 Y-500 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 X5 Y5 F6000 ; go back a few mm
G1 S1 X-235 Y-215 F360 ; move slowly to X and Y axis endstops once more (second pass)
G90 ; absolute positioning
G1 X250 Y250 F6000 ; go to first bed probe point and home Z
G30 ; home Z by probing the bed
; Uncomment the following lines to lift Z after probing
G91 ; relative positioning
G1 S2 Z20 F100 ; lift Z relative to current position
G90 ; absolute positioning

Thanks in advance

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun May 24 2020 20:05:38 GMT+0200 (Central European Summer Time)
G91                      ; relative positioning
G1 H2 Z10 F24000          ; lift Z relative to current position
G1 H1 X-505 Y-505 F12000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F24000       ; go back a few mm
G1 H1 X-505 Y-505 F240   ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-505 F240         ; move Z down stopping at the endstop
G90                      ; absolute positioning
G1 X100 Y100 F2000 ; put head over the centre of the bed, or wherever you want to probe
G30 ; lower head, stop when probe triggered and set Z to trigger height

; Uncomment the following lines to lift Z after probing
G91                     ; relative positioning
G1 Z10 F400              ; lift Z relative to current position
G90                     ; absolute positioning

Here is my file, also i dont understand "Where is the your code to create the height map?" ? I was folowing this guide :link text

@fcwilt Ok will do that

Ok, how about now ?[0_1612359597243_homeall (1).g](Uploading 100%)

Ok did some changes, would you take a look a the new files. homeall.g config.g bed.g