Issues setting up duet 3
-
@bearer fair enough.
Well let’s say I want my duet in standalone mode. From my understanding I need a micro SD in the duet. How do I set this up properly? -
@Vanbluca said in Issues setting up duet 3:
@bearer fair enough.
Well let’s say I want my duet in standalone mode. From my understanding I need a micro SD in the duet. How do I set this up properly?Pretty much the same way as a Duet 2 Ethernet board, except you choose Duet 3 in https://configtool.reprapfirmware.org/
The caveat here is the SD card supplied with the Duet 3 contains the Raspberry Pi operating system, so it is possible computer gets a little confused when trying to access the card. It is safest to format the card and upload the files generated by the configtool.
Use https://www.sdcard.org/downloads/formatter/ to format the card. (Don't worry, if you want to go back to using the card with the raspberry pi, you can download the DuetPi image and write it back to the card later (using etcher or win32diskimager).
The https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7 for the Duet 2 will be mostly valid for the Duet 3 as well if you need to connect via USB to configure your network for some reason.
-
@bearer so I reformatted the sd and it is empty now. Do you have a good guide on what files I should put on the SD now? I already made the config.zip through the RepRap page, but I assume that's not all I put on the SD
-
@Vanbluca come to think of it it needs decompressing and placing into /sys and /www on the sd card.
ref https://duet3d.dozuki.com/Wiki/SD_Card#Section_Creating_the_file_structure
(it won't match 100% but close enough hopefully)
-
doing some more thinking - if its a new board it probably shipped with RRF 3.0b12. So you would have to install 3.0 release first, then update to 3.1.1.
(if you didn't get a download link to a DuetWebControl.zip file then grab https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/DuetWebControl-SD-2.04.zip and extract to /www on the SD card before putting it in the Duet3)
download https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/Duet2and3Firmware-3.0.zip and upload it to DuetWebControl once you're connected.
then repeat with https://github.com/Duet3D/RepRapFirmware/releases/download/3.1.1/Duet2and3Firmware-3.1.1.zip
-
@bearer at this point everything is confusing me.
without any sd in my duet, I can't get it connected to my computer. is that normal? -
@Vanbluca said in Issues setting up duet 3:
without any sd in my duet, I can't get it connected to my computer
without a sd card you can (only) connect with usb and use a serial terminal (ref the getting connected guide).
at that point you can enable the network (but the files for the webserver should be on the sd card so network won't help much without the card)
-
@bearer I tried exactly that and got an error “permission denied”
-
and from my understanding I need to connect the duet first before I can do pretty much anything
-
when connecting via serial? which software, which operating system?
-
@Vanbluca said in Issues setting up duet 3:
and from my understanding I need to connect the duet first before I can do pretty much anything
sort of, but if you have the network config in config.g + the DuetWebControl files in place and boot with the SD card you should be able to access http://duet3/ just like that.
-
@bearer yeah I just connected the USB. I use Mac and typed the commands in Terminal exactly as the guide said
-
Mac, right. the permission denied probaly means you need elevated access rights to run the command on the Mac.
-
@bearer The DuetWebControl files, aren't they just the files from the "SD_Card_Contents.zip" download? or do you need to change them?
-
@Vanbluca said in Issues setting up duet 3:
"SD_Card_Contents.zip"
they are likely ancient. use these instead
(if you didn't get a download link to a DuetWebControl.zip file then grab https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/DuetWebControl-SD-2.04.zip and extract to /www on the SD card before putting it in the Duet3)
-
@Vanbluca said in Issues setting up duet 3:
@bearer at this point everything is confusing me.
Sorry in advance, cant resist......
And respect to @bearer you are a very brave man indeed..........
Might I suggest you take up another form of additive manufacturing which might suit you better.
Its called knitting, two needles and a ball of yarn, nothing more to do, and away you go...
-
@CaLviNx Also can't resist, but you do realise that your "advice" will bite you in the ar*e the next time you ask for advice (as you did fairly recently IIRC).
-
And I think you well know it's not often you see me asking anything let alone advice, I think in all the years you could count that on one hand.................
Asking for assistance is a LAST resort, and even then I have found some of the assistance to turn out plain wrong (but for the sake of respect I haven't posted about it) So back to mainly working it out on my own.
-
@CaLviNx @deckingman Do we need to create a forum for old farts to snip at each other?
-
@Phaedrux said in Issues setting up duet 3:
@CaLviNx @deckingman Do we need to create a forum for old farts to snip at each other?
Excellent idea! I guess now that you've called me an old fart, you'll want to join too.
