Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    bltouch

    Scheduled Pinned Locked Moved Unsolved
    General Discussion
    3
    57
    1.9k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • nemecekundefined
      nemecek
      last edited by

      yes

      M122
      

      === Diagnostics ===
      RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
      Board ID: 08DGM-956GU-DJMSN-6J1FL-3SJ6S-T9NVD
      Used output buffers: 3 of 24 (9 max)
      === RTOS ===
      Static ram: 25712
      Dynamic ram: 92604 of which 396 recycled
      Exception stack ram used: 432
      Never used ram: 11928
      Tasks: NETWORK(ready,628) HEAT(blocked,1232) MAIN(running,348) IDLE(ready,160)
      Owned mutexes:
      === Platform ===
      Last reset 00:40:29 ago, cause: power up
      Last software reset at 2020-06-28 19:10, reason: User, spinning module GCodes, available RAM 11968 bytes (slot 1)
      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
      Error status: 0
      Free file entries: 10
      SD card 0 detected, interface speed: 20.0MBytes/sec
      SD card longest block write time: 6.1ms, max retries 0
      MCU temperature: min 29.1, current 40.2, max 40.8
      Supply voltage: min 11.9, current 12.1, max 12.2, under voltage events: 0, over voltage events: 0, power good: yes
      Driver 0: standstill, SG min/max 0/381
      Driver 1: standstill, SG min/max 0/371
      Driver 2: standstill, SG min/max 0/377
      Driver 3: standstill, SG min/max not available
      Driver 4: standstill, SG min/max not available
      Date/time: 2020-06-28 20:37:50
      Cache data hit count 4294967295
      Slowest loop: 49.05ms; fastest: 0.07ms
      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
      === Move ===
      Hiccups: 0, FreeDm: 160, MinFreeDm: 154, MaxWait: 305348ms
      Bed compensation in use: mesh, comp offset 0.000
      === DDARing ===
      Scheduled moves: 422, completed moves: 422, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
      === Heat ===
      Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
      === GCodes ===
      Segments left: 0
      Stack records: 2 allocated, 0 in use
      Movement lock held by null
      http is idle in state(s) 0
      telnet is idle in state(s) 0
      file is idle in state(s) 0
      serial is idle in state(s) 0
      aux is idle in state(s) 0
      daemon is idle in state(s) 0
      queue is idle in state(s) 0
      autopause is idle in state(s) 0
      Code queue is empty.
      === Network ===
      Slowest loop: 15.44ms; fastest: 0.00ms
      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
      HTTP sessions: 1 of 8

      • WiFi -
        Network state is running
        WiFi module is connected to access point
        Failed messages: pending 0, notready 0, noresp 0
        WiFi firmware version 1.23
        WiFi MAC address 5c:cf:7f:76:6a:14
        WiFi Vcc 3.34, reset reason Turned on by main processor
        WiFi flash size 4194304, free heap 25944
        WiFi IP address 192.168.1.35
        WiFi signal strength -63dBm, reconnections 0, sleep mode modem
        Socket states: 0 0 0 0 0 0 0 0
      1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator
        last edited by

        So what exactly happens when you have it set to P9 and do this test?

        https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe#Section_Static_test_using_the_web_interface

        Z-Bot CoreXY Build | Thingiverse Profile

        1 Reply Last reply Reply Quote 0
        • nemecekundefined
          nemecek
          last edited by

          it goes down without extracting the pin😭

          1 Reply Last reply Reply Quote 0
          • nemecekundefined
            nemecek
            last edited by

            total panic😬

            1 Reply Last reply Reply Quote 0
            • Phaedruxundefined
              Phaedrux Moderator
              last edited by

              And yet using M401 and M402 and G30 works?

              @nemecek said in bltouch:

              m401 m402 g30 everything works

              Z-Bot CoreXY Build | Thingiverse Profile

              1 Reply Last reply Reply Quote 0
              • nemecekundefined
                nemecek
                last edited by

                yes weird

                1 Reply Last reply Reply Quote 0
                • nemecekundefined
                  nemecek
                  last edited by nemecek

                  what can I do? do I stay in P5?

                  1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator
                    last edited by

                    So does g30 cause it to drop the pin or not?

                    Z-Bot CoreXY Build | Thingiverse Profile

                    nemecekundefined 1 Reply Last reply Reply Quote 0
                    • nemecekundefined
                      nemecek @Phaedrux
                      last edited by

                      @Phaedrux yes

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        So I'm quite confused now. Is the BLtouch working or not?

                        Does G32 work to run the auto calibration?

                        Z-Bot CoreXY Build | Thingiverse Profile

                        nemecekundefined 1 Reply Last reply Reply Quote 0
                        • nemecekundefined
                          nemecek @Phaedrux
                          last edited by

                          @Phaedrux yes on p5 everything works if instead I switch to p9 the g29 and g32 the probe does not come out

                          1 Reply Last reply Reply Quote 0
                          • Phaedruxundefined
                            Phaedrux Moderator
                            last edited by

                            Can you go through this section and perhaps create a new beg.g

                            https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareDeltaPrinter#Section_Setting_up_the_auto_calibration_file

                            Z-Bot CoreXY Build | Thingiverse Profile

                            1 Reply Last reply Reply Quote 0
                            • nemecekundefined
                              nemecek
                              last edited by

                              ; bed.g
                              ; called to perform automatic delta calibration via G32
                              ;
                              ; generated by RepRapFirmware Configuration Tool v3.1.3 on Sun Jun 28 2020 15:07:30 GMT+0200 (heure d’été d’Europe centrale)
                              M561 ; clear any bed transform
                              G28 ; home all towers
                              ; Probe the bed at 10 peripheral and 6 halfway points, and perform 8-factor auto compensation
                              ; Before running this, you should have set up your Z-probe trigger height to suit your build, in the G31 command in config.g.
                              G30 P0 X0 Y69.49 H0 Z-99999
                              G30 P1 X49.78 Y68.51 H0 Z-99999
                              G30 P2 X95.11 Y30.9 H0 Z-99999
                              G30 P3 X95.11 Y-30.9 H0 Z-99999
                              G30 P4 X58.78 Y-80.9 H0 Z-99999
                              G30 P5 X0 Y-100 H0 Z-99999
                              G30 P6 X-51.7 Y-71.16 H0 Z-99999
                              G30 P7 X-67.44 Y-21.91 H0 Z-99999
                              G30 P8 X-60.9 Y19.79 H0 Z-99999
                              G30 P9 X-37.4 Y51.48 H0 Z-99999
                              G30 P10 X0 Y25.56 H0 Z-99999
                              G30 P11 X35.2 Y20.32 H0 Z-99999
                              G30 P12 X43.3 Y-25 H0 Z-99999
                              G30 P13 X0 Y-50 H0 Z-99999
                              G30 P14 X-24.1 Y-13.91 H0 Z-99999
                              G30 P15 X-20.01 Y11.55 H0 Z-99999
                              G30 P16 X0 Y0 H0 Z-99999 S8
                              ; Use S-1 for measurements only, without calculations. Use S4 for endstop heights and Z-height only. Use S6 for full 6 factors
                              ; If your Z probe has significantly different trigger heights depending on XY position, adjust the H parameters in the G30 commands accordingly. The value of each H parameter should be (trigger height at that XY position) - (trigger height at centre of bed)

                              1 Reply Last reply Reply Quote 0
                              • nemecekundefined
                                nemecek
                                last edited by

                                do you think the problem comes from here?

                                1 Reply Last reply Reply Quote 0
                                • Phaedruxundefined
                                  Phaedrux Moderator
                                  last edited by

                                  I'm not sure. You cna use this tool to generate a new one: http://escher3d.com/pages/wizards/wizardbed.php

                                  If it all works with P5 then that's not the end of the world. I just don't understand why P9 doesn't work.

                                  Z-Bot CoreXY Build | Thingiverse Profile

                                  1 Reply Last reply Reply Quote 0
                                  • nemecekundefined
                                    nemecek
                                    last edited by nemecek

                                    I don't have M401 in my bed.g How come? maybe that's why it doesn't work Sans titreo.png

                                    JoergS5undefined 1 Reply Last reply Reply Quote 0
                                    • JoergS5undefined
                                      JoergS5 @nemecek
                                      last edited by

                                      @nemecek if you set P9 mode, I would set P value of G31 lower:
                                      G31 P500 X-45.712 Y36.357 Z2.5
                                      =>
                                      G31 P25 X-45.712 Y36.357 Z2.5

                                      The 500 was an example in the G31 section, but P25 is used in most documentation about BLTouch P9 examples.

                                      nemecekundefined 1 Reply Last reply Reply Quote 0
                                      • nemecekundefined
                                        nemecek @JoergS5
                                        last edited by

                                        @JoergS5
                                        ok and for this reason that did not work in P9? I'll try tomorrow thanks

                                        JoergS5undefined 1 Reply Last reply Reply Quote 0
                                        • nemecekundefined
                                          nemecek
                                          last edited by

                                          sorry how do you save the delta calibration?
                                          when i turn the printer off and on again i lose the g32 i had made ...
                                          what do you think you can print like this? or it is too wrong

                                          livello.png

                                          Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                          • Phaedruxundefined
                                            Phaedrux Moderator @nemecek
                                            last edited by

                                            @nemecek said in bltouch:

                                            sorry how do you save the delta calibration?

                                            M500 will save the calibration to the config-override.g file and you will need to add M501 to the end of your config.g to load the config-override.g file at boot time.

                                            @nemecek said in bltouch:

                                            I don't have M401 in my bed.g How come? maybe that's why it doesn't work

                                            With P9 the probe should be deployed automatically when needed, so no need to manually call M401, etc.

                                            Z-Bot CoreXY Build | Thingiverse Profile

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA