Duet Wifi 1.04 on Ender5,motor noise

lui2004

@JoergS5 said in Duet Wifi 1.04 on Ender5,motor noise:

M122

Hi

the Motors for x,y and z are stock from Ender 5 only the Extruder motor was changed to this one:

thats my firmware version:
Board: Duet 2 WiFi (2WiFi)
Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.1.1 (2020-05-19b2)
Duet WiFi Server Version: 1.23

M112:

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917NK-F23T0-6JTD2-3S86S-KYBND
Used output buffers: 3 of 24 (14 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93840 of which 44 recycled
Exception stack ram used: 544
Never used ram: 8664
Tasks: NETWORK(ready,368) HEAT(blocked,1224) MAIN(running,1552) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:00:55 ago, cause: power up
Last software reset at 2020-07-24 22:31, reason: User, spinning module GCodes, available RAM 8736 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 28.4, current 31.6, max 31.8
Supply voltage: min 24.2, current 24.4, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/232
Driver 1: standstill, SG min/max 88/216
Driver 2: standstill, SG min/max 0/312
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-07-25 08:54:29
Cache data hit count 95067176
Slowest loop: 4.60ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 167, MaxWait: 23772ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 12, completed moves: 12, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 155.68ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 84:f3:eb:83:4f:81
WiFi Vcc 3.45, reset reason Unknown
WiFi flash size 4194304, free heap 23568
WiFi IP address 192.168.2.112
WiFi signal strength -68dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

Config.g:

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)

; General preferences
G90                                      ; Send absolute coordinates...
M83                                      ; ...but relative extruder moves

; Network
M550 P"Ender 5"                          ; Set machine name
M552 S1                                  ; Enable network
M587 S"WLAN-110995" P"39510069647710671890"                 ; Configure access point. You can delete this line once connected
M586 P0 S1                               ; Enable HTTP
M586 P1 S0                               ; Disable FTP
M586 P2 S0                               ; Disable Telnet

; Drives
M569 P0 S1                               ; Physical drive 0 goes forwards
M569 P1 S1                               ; Physical drive 1 goes forwards
M569 P2 S0                               ; Physical drive 2 goes backwards
M569 P3 S0                               ; Physical drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1                 ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E411.53        ; Set steps per mm
M566 X600.00 Y600.00 Z60.00 E300.00      ; Set maximum instantaneous speed changes (mm/min)
M203 X30000.00 Y30000.00 Z500.00 E6000.00  ; Set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z200.00 E6000.00    ; Set accelerations (mm/s^2)
M906 X580.00 Y650.00 Z580.00 E650.00 I10  ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                         ; Set axis minima
M208 X220 Y220 Z300 S0                   ; Set axis maxima

; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"                            ; configure active-high endstop for low end on Z via pin zstop

; Z-Probe
M558 PO H2 F120 T6000
M557 X20:220 Y20:220 S65                       ; define mesh grid
M376 H20

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B3950  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00           

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                            ; Define tool 0
G10 P0 X0 Y0 Z0                          ; Set tool 0 axis offsets
G10 P0 R0 S0                             ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured
M501
M575 P1 S1 B57600

homeall:

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
G91                     ; relative positioning
G1 Z5 F6000 H2          ; lift Z relative to current position
G1 H1 X-225 Y-225 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 X5 Y5 F6000          ; go back a few mm
G1 H1 X-225 Y-225 F360  ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-305 F1800       ; move Z down stopping at the endstop
G90                     ; absolute positioning
G92 Z0                  ; set Z to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 S2 Z5 F100          ; lift Z relative to current position
;G90                    ; absolute positioning

homex.g:

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
G91               ; relative positioning
G1 Z5 F6000 H2    ; lift Z relative to current position
G1 H1 X-225 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000       ; go back a few mm
G1 H1 X-225 F360  ; move slowly to X axis endstop once more (second pass)
G1 Z-5 F6000 H2   ; lower Z again
G90               ; absolute positioning

homey.g:

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
G91               ; relative positioning
G1 Z5 F6000 H2    ; lift Z relative to current position
G1 H1 Y-225 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F6000       ; go back a few mm
G1 H1 Y-225 F360  ; move slowly to Y axis endstop once more (second pass)
G1 Z-5 F6000 H2   ; lower Z again
G90               ; absolute positioning

homez.g:

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v2 on Tue May 07 2019 23:06:50 GMT+0100 (British Summer Time)
G91               ; relative positioning
G1 Z5 F6000 H2    ; lift Z relative to current position
G1 H1 Z-305 F1800 ; move Z down until the endstop is triggered
G92 Z0            ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91              ; relative positioning
;G1 S2 Z5 F100    ; lift Z relative to current position
;G90              ; absolute positioning

lui2004

@JoergS5 said in Duet Wifi 1.04 on Ender5,motor noise:

6000

a little video:
https://streamable.com/47zfq5

JoergS5

@lui2004 did you try changing
M203 X30000.00 Y30000.00 Z500.00 E6000.00
to
M203 X6000.00 Y6000.00 Z500.00 E6000.00
and then turn off/on printer to be sure the change is active?

I don't see errors in M122 and config.

lui2004

yes i have changed the values but still the same with noise

JoergS5

@lui2004 I watched the video with audio on now
My impression is, the most noise don't come from the steppers, but the fans. It's difficult to decide. Probably after homing some fans are activated because something heats up (heatbreak fan eg).

Your trapezoid spindle for Z movement is black, this may be abrasive from some spindle nut or you needed lubrication. There may be too much friction between nut and spindle. This could produce noise also (and has the danger of slip-stick and inexact Z movement also). The coupler between stepper and spindle is of a type where the stepper and trapezoid axis must match exactly. Better would be dog clutch (Rotex coupler, Oldham). They are better than those aluminium coupler with horizontal gaps.

Phaedrux

It's hard to tell from the video if it's fan noise or the motor idle noise. The creality motors are a bit noisier on the Duet I think. There is a bit more whine from them.

M906 X580.00 Y650.00 Z580.00 E650.00 I10 ; Set motor currents (mA) and motor idle factor in per cent

Current setting on the Duet 2 WiF/Ethernet is done in steps of 100mA and is rounded down. Current setting on the Duet Maestro is in steps of 50mA and rounded down.

https://duet3d.dozuki.com/Wiki/Gcode#Section_M906_Set_motor_currents

So keep that in mind when setting your currents.

You may find this helpful: https://duet3d.dozuki.com/Wiki/Reducing_Stand-Still_Noise

lui2004

@Phaedrux said in Duet Wifi 1.04 on Ender5,motor noise:

M906 X580.00 Y650.00 Z580.00 E650.00 I10 ; Set motor currents (mA) and motor idle factor in per cent

this parameters are from marlin

M906 X580.00 Y650.00 Z580.00 E650.00 I10 ; Set motor currents (mA) and motor idle factor in per cent

so if i have the Duet wifi how to set up ? like this ?

M906 X480.00 Y550.00 Z480.00 E550.00 I10 ; Set motor currents (mA)

JoergS5

@lui2004 can you locate what is loud? X, Y, Z steppers or fans (and which fan)?

Phaedrux

Those values will be rounded down to the nearest 100ma.

So this: M906 X480.00 Y550.00 Z480.00 E550.00

Will actually be this: M906 X400.00 Y500.00 Z400.00 E500.00

lui2004

@JoergS5

all motors

i will try this on monday: https://duet3d.dozuki.com/Wiki/Reducing_Stand-Still_Noise

lui2004

Hi

the noise from the motors seems like rustle