thermistor bad reading
-
@ninni said in thermistor bad reading:
@Veti may you link me the website where i can buy it?
-
@Phaedrux sorry i dont understand
veti said me that semitec-104nt o pt1000 is very ood sensor -
This post is deleted! -
@droftarts ; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X200.00 Y200.00 Z800.00 E873.08 ; set steps per mm
M566 X600.00 Y600.00 Z18.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z240.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z100.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X230 Y210 Z210 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-low endstop for high end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-low endstop for high end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop; Z-Probe
M558 P1 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
M557 X0:22 Y0:22 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S250 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B3950 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T1 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P1 D0 H1 F0 ; define tool 1
G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T1 ; select first tool -
@ninni said in thermistor bad reading:
@Phaedrux sorry i dont understand
veti said me that semitec-104nt o pt1000 is very ood sensorI linked you to the E3D Semitec-104GT thermistor cartridge which is what I think Veti was referring to. I don't think you'll find a better or easier to obtain thermistor with known values and appropriate form factor.
-
@Phaedrux ok tu so Much
-
Does your hotend heat block take a cartridge thermistor or a glass bead?
-
@Phaedrux block thermistor
-
Does it look like the little metal tube in the E3D link above, or does it look like a little glass bead?
-
@Phaedrux small metal tube
-
Then that E3D thermistor is the one you want.
-
https://de.aliexpress.com/item/32859917151.html
this is the alternative pt1000
-
@Veti ok we Will see
-
also I would like to report a bug. when the endstop is positioned upwards for the z axis the platter stops when it touches the endstop but if you give the command again it continues to rise ignoring that the limit switch was already pressed
; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Sep 26 2020 13:33:30 GMT+0200 (Ora legale dell’Europa centrale)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-235 Y-215 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-235 ; home X axis
G1 H1 Y-215 ; home Y axis
G1 X5 Y5 F6000 ; go back a few mm
G1 H1 X-235 F360 ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-215 ; then move slowly to Y axis endstop
G1 H1 Z205 F360 ; move Z up stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis maximum (you may want to adjust this); Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sat Sep 26 2020 13:34:47 GMT+0200 (Ora legale dell’Europa centrale)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Z205 F1800 ; move Z up until the endstop is triggered
G92 Z0 ; set Z position to axis maximum (you may want to adjust this); Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioningconfig.g
; Axis Limits
M208 X0 Y0 Z-200 S1 ; set axis minima
M208 X230 Y210 Z0 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z2 S1 P"zstop" ; configure active-high endstop for high end on Z via pin zstop -
@ninni said in thermistor bad reading:
M208 X0 Y0 Z-200 S1 ; set axis minima
M208 X230 Y210 Z0 S0 ; set axis maximaNot a bug; you have put in strange values for Z axis minima and maxima. Firmware expects all moves to be in the positive range; no CAM/ slicer outputs negative absolute coordinates.
Ian
-
@ninni said in thermistor bad reading:
also I would like to report a bug. when the endstop is positioned upwards for the z axis the platter stops when it touches the endstop but if you give the command again it continues to rise ignoring that the limit switch was already pressed
The reason for that is the G1 H2 Z5 command in your homez.g file. That command tells the firmware to raise Z by 5mm, but that isn't appropriate when homing to max Z. You should probably remove the one in homeall.g too.
