Tips to mitigate vertical artifacting Duet 2 Wifi
-
Well, I am going to take that back. The single wall prints are much improved by the 0.9 steppers. Top one is before.
-
Chris, fan of your videos and appreciate your contributions to the community.
One question, can you do a single wall test with varying line widths? For instance, 0 to 9.8mm at .4 mm width, 10 to 19.8 .42mm width, etc. In the past, I’ve found vertical or diagonal lines like this caused by inconsistent extrusion and can point to an issue with your extruder. If you perform a single wall test with extrusion parameters that vary at different heights and the angle of the diagonal lines changes, there could be an issue with inconsistent extrusion.
The key is to see if the angle of the diagonal line artifacts changes with varying extrusion parameters.
-
hi chris.
i presume that you have done the mechanical checks.
corexy are very susceptible to problems in the belt path.- bad pulleys
- toothed belt on smooth pulley
- belts not parallel
also check for slight belt twisting when the direction of movement of the belt changes.
16 tooth pulley can improve the effect from switching from 1.8 to 0.9 pulleys further.
-
@Veti I have been over it many times and I am still running belts over smooth pullies. That is my next move. I need to find some toothed pullies that will fit my setup. I am currently using flanged bearings.
-
@mwolter Thank you! That's an interesting thought. I will setup a test and see what happens.
-
@brotherchris
If you are running them over F623zz then finding a good tooth pulley will be hard.
the only thing that comes close are Gates Powergrip
2GT Idlers, buy they are 5mm ID. -
@Veti Yeah, that kind of sucks. I have been looking for alternatives all morning, but 5mm bore is about my only option. I really didn't want to go down that small. I am determined to find some sort of work around.
-
what quality are your F623zz ? for a corexy they should be ABEC-3 or above.
-
i am going to test these myself once they arrive.
https://www.aliexpress.com/item/4000040551804.html
but i dont have high hopes -
@Veti I am actually using F688ZZ. Not sure the grade.
-
@brotherchris said in Tips to mitigate vertical artifacting Duet 2 Wifi:
F688ZZ
closest thing i can find is
https://www.aliexpress.com/item/32961265334.html
but its 6mm bore -
@Veti I am trying 16 tooth idlers like this on my kossel delta, but have bought some 6x2.5x3mm bore bearings, and pressed 3 into each idler. You clamp the idler firmly (not possible with the original 2 bearing idlers), but you need 3mm bore washers that are 4.5mm diameter to do this. Will be interesting to see if they last longer.
-
@brotherchris said in Tips to mitigate vertical artifacting Duet 2 Wifi:
@Veti Yeah, that kind of sucks. I have been looking for alternatives all morning, but 5mm bore is about my only option. I really didn't want to go down that small. I am determined to find some sort of work around.
It seems you think 5mm is too small. Why do you think that is so?
Thanks.
Frederick
-
@fcwilt It's not that I think it's too small, I just wanted a little larger hardware on this setup.
-
@brotherchris said in Tips to mitigate vertical artifacting Duet 2 Wifi:
I need to find some toothed pullies that will fit my setup.
I was able to do a few belt twists to run the smooth side of the belt over my flanged bearings. When I tried toothed idlers there was still a lot of ridges. I think the small 16T idlers are just too tight of a bend for the teeth to mesh smoothly. I was able to have the belt twists on the fixed length sections between the motor and the rear idlers.
-
@brotherchris said in Tips to mitigate vertical artifacting Duet 2 Wifi:
It's not that I think it's too small, I just wanted a little larger hardware on this setup.
ok then here you go.
https://www.aliexpress.com/item/32961693003.html
its 8mm bore.
but the diameter is larger than the F688ZZ -
@Phaedrux Run a test with a belt twist now.
-
@Veti Nice find, I am going to grab some for testing.
-
@Phaedrux Still confused, the belt flip didn't change anything.
-
@brotherchris said in Tips to mitigate vertical artifacting Duet 2 Wifi:
@Phaedrux Still confused, the belt flip didn't change anything.
Well that's one more thing to cross off the list and leaves stepper artifacts. I wonder if it's related to the exoslide movement? Is there more or less resistance to motion with it?
Were you able to print a test that varied the speed over a range to try and see if there is a speed which doesn't excite the artifacts?
