change or add a ON/Off button instead of a slider

oliof

Shouldn't you redefine the pins in question as general GPIO pins and then control them with M42? Then you'd get no fan entry (and no buttons -- but in my setup I have two macros "0_led on" and "1_led off" which run M42 P0 S255 and M42 P0 S0 respectively and due to their name they are at the top of the list of Macros. Suits me (-:

fcwilt

@oliof said in change or add a ON/Off button instead of a slider:

Shouldn't you redefine the pins in question as general GPIO pins and then control them with M42?

So it's possible to do that to what would normally be a fan connection?

If that is what you are saying, could you post a example of the command(s) needed to do that?

Thanks.

Frederick

Phaedrux

@fcwilt In RRF3 you use M950 to define your pins. So you could define a servo pin and then target it with M42.

https://duet3d.dozuki.com/Wiki/Gcode#Section_M950_Create_heater_fan_or_GPIO_servo_pin

https://duet3d.dozuki.com/Wiki/Gcode#Section_M42_Switch_I_O_pin

M950 S0 C"fan0" Q500
M42 P0 S255/S0

If you were using a BLTouch I think you'd need to choose the next available servo number, so S1/P1

fcwilt

@Phaedrux

Thanks.

I have failed to realize what M950 can do.

I was thinking that it just declared that you were going to use a specific heater, fan or servo as a heater, fan or servo.

I didn't realize that it could change a fan connection into a servo connection. That is very useful.

Frederick

Phaedrux

@fcwilt said in change or add a ON/Off button instead of a slider:

I didn't realize that it could change a fan connection into a servo connection. That is very useful.

Yes that is one of the big reasons for RRF3 to make the I/O more generalized and easier to manage over the fixed function of RRF2. This is exemplified in the hardware design of Duet 3 where all specific ports have been replaced in favour of more general i/o leaving it up to the user to define.

fcwilt

@Phaedrux said in change or add a ON/Off button instead of a slider:

Yes that is one of the big reasons for RRF3 to make the I/O more generalized and easier to manage over the fixed function of RRF2. This is exemplified in the hardware design of Duet 3 where all specific ports have been replaced in favour of more general i/o leaving it up to the user to define.

I now see why the Duet 3 has more generic names - I like that.

I think the use of specific names like fan0 is what led to my misunderstanding. My fault for not reading with greater comprehension.

Thanks much.

Frederick

tracar

Ok so from what i have read makes no sense to me, lol

the picture i have attached shows me clicking on the (Neopixels on/off) tab
Can this tab be an actual button to toggle on and off at full power, and remove the slider ?

this is what i have:

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"Tool fan" P1 S0 H-1 T45 ; set fan 0 value. Thermostatic control is turned on "H-1 disables thermostatic mode" or H1 enables. "S" parameter turns that fan on or off S0 or S1 T45 is fan on at 45 degrees

M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"Parts cooling fan" S0 H-1 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"e1heat" Q20000 ; create fan 2 on pin e1heat and set its frequency ( connected to relay )
M106 P2 C"Neopixels ON/OFF" S0 H-1 ;set fan 2 name and value. Thermostatic control is turned off
M950 F3 C"fan2" Q20000 ; create fan 0 on pin fan0 and set its frequency ( connected to relay )
M106 P3 C"Relay 2 ON/OFF" S0 H-1

OR can io create a whole new section under the " fan Control " section just for led and stuff with buttons?

Phaedrux

@tracar Sorry it's not currently that flexible. I can move this to the wish list.

tracar

@Phaedrux
thanks for the reply.

Phaedrux

What @oliof is talking about would put on/off buttons on the macros list on the right side of your photo and remove the LEDs listing from the fan control entirely.