It has taken me a few months to Design Cut and get it up and running with the help of @Droftarts , @Phaedrux , @Jay_s_uk , @Peter247 , Aaaaand @Hayseed_Byte their guidance and help was amazing , along with the million posts to read here at this forum 
thanks to everyone
for now i will just post a few photos if i can to show what is being controlled by a duet2 wifi board.
Video:
https://youtu.be/IGhwmslqyvE
@Phaedrux said in pwm fan2 on the duet2 wifi:
but you haven't given much context about your setup at all and I'
Yes Sorry for the confusion..
3.1.1
duet2 wifi
so as you probably could guess, yes im looking for a way to control a led strip ( at least power some from a single pin .
so need to configure a pin to be an on and off signal/voltage and have this output connected to a isolation voltage converter then to the led controller.
my current setup:
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"Tool fan" P1 S0 H-1 T45 ; set fan 0 value. Thermostatic control is turned on "H-1 disables thermostatic mode" or H1 enables. "S" parameter turns that fan on or off S0 or S1 T45 is fan on at 45 degrees
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"Parts cooling fan" S0 H-1 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"fan2" Q20000 ; create fan 2 on pin fan2 and set its frequency
M106 P2 C"LED's Brightness" S0 H-1 ;set fan 2 name and value. Thermostatic control is turned off
with the above i can control Via the web interface with a slider to turn it on and off,
trying to get it to turn on and off with macros..
@tracar so annoying lol:
Error
As a new user, you can only post once every 60 second(s) until you have earned 1 reputation - please
make the changes to config file, save ,reset board send command M280 P0 S10
@Phaedrux said in hbot homes correctly but prints mirrored ,:
to get a heightmap of the bed surface itself to s
flawless !!!
you rock.
@Phaedrux i will try to recreate the situation after the print is done, , if it spikes i can verify with a thermal probe too.... post my findings later
@Phaedrux said in Connection issue on long prints.:
y weird. It could be interference on your thermistor wiring, or a bad connection.
that is the only time the heater did that,, directly after m112, while it was sitting there with the trying to reconnect popup. and as you can see i entered m112 twice,,, just as the heat graph shows, then the time where it dropped off in temp as i hit the reconnect button,,,
kinda what i was thinking, after everything else can just not the pc...
did you notice the heaters did that little thing off the scale ?
@tracar said in Connection issue on long prints.:
dont see the fix. after many hours the webpage dro
M122 after the connection problem...
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS4-7J9D4-3S86R-KAA3N
Used output buffers: 3 of 24 (21 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73860 of which 80 recycled
Never used RAM 14680, free system stack 103 words
Tasks: NETWORK(ready,180) HEAT(blocked,309) MAIN(running,402) IDLE(ready,19)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 13:58:41 ago, cause: software
Last software reset at 2021-01-15 20:44, reason: User, GCodes spinning, available RAM 14924, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 25.7, current 27.7, max 28.8
Supply voltage: min 23.8, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 86402, standstill, SG min/max not available
Driver 1: position -17072, standstill, SG min/max not available
Driver 2: position 17952, standstill, SG min/max not available
Driver 3: position 0, ok, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-16 10:43:32
Cache data hit count 4294967295
Slowest loop: 69.13ms; fastest: 0.18ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 5.0ms, write time 2.1ms, max retries 0
=== Move ===
DMs created 83, maxWait 194553ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 536861, completed moves 536855, hiccups 2, stepErrors 0, LaErrors 0, Underruns [118, 0, 0], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X228.584 Y264.573 E0.7917" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.81ms; fastest: 0.10ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
++++++++++++++++
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Aug 30 2020 09:00:14 GMT-0600 (Mountain Daylight Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Duet2" ; set printer name
M669 K1 ; select CoreXY mode
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Input/Output Physical Estop
M950 J1 C"e1stop" ; e1_stop pin on the mainboard
M581 P1 T0 C0 S0 ; T0 = emergency stop on trigger
; Drives
M569 P5 S1 T5 R1 ; physical drive x goes forwards
M569 P6 S1 T5 R1 ; physical drive y goes forwards
M569 P7 S1 T5 R1 ; physical drive z goes forwards
M569 P8 S1 T5 R1 ; physical drive U goes forwards
M569 P3 S1 ; physical drive extruder goes forwards
M584 X6 Y5 Z7:8 E3 ; set drive mapping
M671 X-50:490 Y330:330 S5 ; x leadscrew position left to right from o,o on y axis , S5 means can adjust up to 5 mm
M350 X16 Y16 Z16 E16 I1 ; configure micro stepping with interpolation
M92 X200.5 Y200.5 Z800.00 E93 ; set steps per mm
; FEEDRATE CONVERSIONS
; 1.6mm/s = F100
; 10mm/s = F600
; 16mm/s = F1000
; 20mm/s = F1200
; 35mm/s = F2100
; 50mm/s = F3000
; 70mm/s = F4200
; 100mm/s = F6000
; 120mm/s = F7200
; 133mm/s = F8000
; 160mm/s = F10000
; 250mm/s = F15000
M566 X1200 Y1200 Z1200 E3000 ; jerk settings testing
;M566 X250.00 Y250.00 Z5.00 E120.00 ; set maximum instantaneous speed changes (mm/min) (original jerk settings)
M203 X8000.00 Y8000.00 Z1000.00 E4000.00 ; set maximum speeds (mm/min)
M201 X200.00 Y200.00 Z15.00 E400.00 ; set accelerations (mm/s^2)
M906 X300 Y300 Z300 E1800 I30 ; set motor currents (mA)
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X440 Y528 Z895 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; configure active-low endstop for high end on X via pin xstop
M574 Y2 S1 P"ystop" ; configure active-low endstop for high end on Y via pin ystop
M574 Z1 S1 P"zstop+e0stop" ; configure active-high endstops for low end on Z via pins zstop and e0stop
; Z-Probe
M950 S0 C"!exp.heater7" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T24000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-.04 Y-26.5 Z3.44 ; set Z probe trigger value, offset and trigger height ( the higher the number the smaller the spacing )
;uncomment one probe grid you want below
M557 X20:430 S205 Y80:535 S212.5 ; define mesh grid With 9 points mapped
;M557 X20:430 S102.5 Y80:535 S106.25 ; define mesh grid With 25 points mapped
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 A138.4 C562.2 D0.8 S1.00 V120.0 B0 ; disable bang-bang mode for Bed and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 A385.4 C119.0 D3.5 S1.00 V24.2 B0 ; disable bang-bang mode for heater and set PWM limit
; Fans
M950 F0 C"fan0" Q500 ; create fan0 on pin fan0 and set its frequency
M106 P0 C"part/bridging fan" P1 S0 H-1 ; set fan0 "H-1 disables thermostatic mode" or H1 enables. ("S" parameter turns that fan on or off S0 or S1) (T45 is fan on at 45 degrees)
M950 F1 C"fan1" Q500 ; create (Tool fan 1) on pin fan1 and set its frequency
M106 P1 C"Hot end fan" S0 H1 T45 ; set (Tool fan 1) value. Thermostatic control is turned off
M950 F2 C"e1heat" Q20000 ; create fan on pin e1heat and set its frequency ( connected to Solid State relay )
M106 P2 C"Neopixels ON/OFF" S1 H-1 ;set fan 2 name and value. Thermostatic control is turned off
M950 F3 C"fan2" Q20000 ; create fan2 on pin fan0 and set its frequency ( connected to Solid State relay )
M106 P3 C"Relay 2 ON/OFF" S0 H-1
; Tools
M563 P0 S"Flexion" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
M501
yes you are correct, the pc will not connect without a restart.
but tablet and cell will , in both local wifi and or cellular only..
i typed m112 instead, Twice,, noob..... anyways look at the temp during the seconds i did not hit the reconect button........... Hmmmmmm
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N8PS4-7J9D4-3S86R-KAA3N
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73652 of which 44 recycled
Never used RAM 14924, free system stack 191 words
Tasks: NETWORK(ready,180) HEAT(blocked,309) MAIN(running,470) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:00:27 ago, cause: software
Last software reset at 2021-01-15 20:44, reason: User, GCodes spinning, available RAM 14924, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 26.0, current 26.7, max 27.2
Supply voltage: min 24.0, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-01-15 20:45:18
Cache data hit count 33439127
Slowest loop: 8.21ms; fastest: 0.23ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.8ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.76ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
im starting another 30 hour print i will repost another M122 after its doneto compare.
its been said here lots, and i dont see the fix. after many hours the webpage drops the connection and hangs, both firefox and chrome. ( in my PC) , now im using the latest firmwares. duet2 wireless.
i have had the same problem before with lower revisions.
i can connect with any of my other devices without issue , just not the PC , unless i restart it.
anyone had this problem, and solved it?
@Phaedrux said in seperate fan controll:
The tool fan slider in DWC is a special slider that is attached to the part cooling fan of the currently selected tool.
so ultimately what i was trying to get going is one fan set up to thermostatically turn on for the tool head when it reaches 45 deg, the second fan can manually be turned on or automatically turned on when a bridging function happens
on duet wifi with latest build
; Fans
M950 F0 C"fan0" Q500 ; create fan0 on pin fan0 and set its frequency
M106 P0 C"part/bridging fan" P1 S0 H-1 ; set fan0 "H-1 disables thermostatic mode" or H1 enables. ("S" parameter turns that fan on or off S0 or S1) (T45 is fan on at 45 degrees)
M950 F1 C"fan1" Q500 ; create (Tool fan 1) on pin fan1 and set its frequency
M106 P1 C"tool fan" S0 H1 T45 ; set (Tool fan 1) value. Thermostatic control is turned off
M950 F2 C"e1heat" Q20000 ; create fan on pin e1heat and set its frequency ( connected to Solid State relay )
M106 P2 C"Neopixels ON/OFF" S1 H-1 ;set fan 2 name and value. Thermostatic control is turned off
M950 F3 C"fan2" Q20000 ; create fan2 on pin fan0 and set its frequency ( connected to Solid State relay )
M106 P3 C"Relay 2 ON/OFF" S0 H-1
it shows up in webface under fan controll as separate fan sliders, named "part/bridging fan" and "tool fan".
the tool fan turns on at 45deg
when a print is started the sliders ( both) do not separate control, but control thepart/bridging fan no matte which slider is moved
What could the issue be?
same problem here exactly as above.., web interface hangs,