Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Newbie: New Install on Ender 5 Plus---Willing to PAY$$$

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    6
    141
    7.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • shattyundefined
      shatty @Veti
      last edited by

      @Veti said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

      @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

      11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
      11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
      11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
      11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2

      this indicates that your wiring of the phases are incorrect.

      see
      https://duet3d.dozuki.com/Wiki/Choosing_and_connecting_stepper_motors#Section_Connecting_stepper_motors

      I triple checked them. I compared from the stock board to the D3D. I will check again

      1 Reply Last reply Reply Quote 0
      • shattyundefined
        shatty @Veti
        last edited by shatty

        @Veti
        so just Extruder,x and y? And just the B phase?

        Vetiundefined 1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators
          last edited by

          As it's only one phase of each driver that's reported as disconnected, a likely cause is a bad crimp connection.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • Vetiundefined
            Veti @shatty
            last edited by

            @shatty

            M584 X0 Y1 Z2

            x y z, presumably you have not moved the extruder.

            the stock board config does not matter, as each board has different layouts.

            did you follow the guide to find the phases of the motors?

            shattyundefined 1 Reply Last reply Reply Quote 0
            • shattyundefined
              shatty @Veti
              last edited by

              @Veti The stock board has the terminals labeled for the ab and 12. I compared them to D3D and it was good.

              shattyundefined dc42undefined 2 Replies Last reply Reply Quote 0
              • shattyundefined
                shatty @shatty
                last edited by shatty

                @shatty Motors are 6 pin. The 2 inner and 2 outer are used. Dunno if that matters

                Vetiundefined 1 Reply Last reply Reply Quote 0
                • Vetiundefined
                  Veti @shatty
                  last edited by

                  @shatty

                  thats normal

                  shattyundefined 1 Reply Last reply Reply Quote 0
                  • shattyundefined
                    shatty @Veti
                    last edited by shatty

                    This post is deleted!
                    1 Reply Last reply Reply Quote 0
                    • dc42undefined
                      dc42 administrators @shatty
                      last edited by dc42

                      @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                      @Veti The stock board has the terminals labeled for the ab and 12. I compared them to D3D and it was good.

                      If you used the same wiring order for the stepper motor connectors on the Duet as they were on the old board, then it should be correct. All boards that I know of put the wires for one phase at one end of the connector, and the other phase at the other end.

                      If you did have the phases incorrectly wired, the error messages would be different.

                      So IMO the most likely cause is a bad crimp connection. I suggest you use a multimeter to measure the resistance of each phase from the connector on the Duet.

                      Duet WiFi hardware designer and firmware engineer
                      Please do not ask me for Duet support via PM or email, use the forum
                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                      shattyundefined 1 Reply Last reply Reply Quote 0
                      • shattyundefined
                        shatty @dc42
                        last edited by shatty

                        @dc42

                        OK what about homing? It keeps trying to go past the limits. Every direction. Where do i move manually the axis?

                        1 Reply Last reply Reply Quote 0
                        • shattyundefined
                          shatty
                          last edited by

                          I havent received any errors for the phases lately

                          1 Reply Last reply Reply Quote 0
                          • shattyundefined
                            shatty
                            last edited by

                            M98 P"0:/macros/01-Test_IR_PD_Homing"
                            Error: in file macro line 12 column 30: M906: array too long, max length = 1
                            Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.

                            1 Reply Last reply Reply Quote 0
                            • shattyundefined
                              shatty
                              last edited by shatty

                              The endstops are not telling the unit to stop moving. It hits the endstop switch and it still tries to move in that direction. But the endstops are functioning because I went to settings and machine specific and when i press them, the value changes

                              1 Reply Last reply Reply Quote 0
                              • shattyundefined
                                shatty
                                last edited by

                                This post is deleted!
                                1 Reply Last reply Reply Quote 0
                                • Vetiundefined
                                  Veti @shatty
                                  last edited by

                                  @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                                  11/16/2020, 1:13:16 AM Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.

                                  this means that your homing files were created for an old version of the firmware.

                                  please generate new ones from the configurator.

                                  shattyundefined 1 Reply Last reply Reply Quote 0
                                  • shattyundefined
                                    shatty @Veti
                                    last edited by shatty

                                    @Veti everything came from same zip. Every file except config.g and *.txt have same time stamps

                                    Vetiundefined 1 Reply Last reply Reply Quote 0
                                    • Vetiundefined
                                      Veti @shatty
                                      last edited by

                                      @shatty

                                      post your homeall.g

                                      1 Reply Last reply Reply Quote 0
                                      • shattyundefined
                                        shatty
                                        last edited by

                                        ; homeall.g
                                        ; called to home all axes
                                        ;
                                        ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time)
                                        G91 ; relative positioning
                                        G1 H2 Z5 F6000 ; lift Z relative to current position
                                        G1 H1 X-355 Y-355 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
                                        G1 H2 X5 Y5 F6000 ; go back a few mm
                                        G1 H1 X-355 Y-355 F360 ; move slowly to X and Y axis endstops once more (second pass)
                                        G90 ; absolute positioning
                                        G1 X-1.3000000000000007 Y1 F6000 ; go to first bed probe point and home Z
                                        G30 ; home Z by probing the bed

                                        ; Uncomment the following lines to lift Z after probing
                                        ;G91 ; relative positioning
                                        ;G1 Z5 F100 ; lift Z relative to current position
                                        ;G90 ; absolute positioning

                                        Vetiundefined 1 Reply Last reply Reply Quote 0
                                        • Vetiundefined
                                          Veti @shatty
                                          last edited by

                                          @shatty

                                          ok then the problem is in

                                          01-Test_IR_PD_Homing

                                          post that.
                                          where did you get that macro?

                                          shattyundefined 1 Reply Last reply Reply Quote 0
                                          • shattyundefined
                                            shatty
                                            last edited by

                                            Recycling is tomorrow. Is the printer recyclable?

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA