Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Newbie: New Install on Ender 5 Plus---Willing to PAY$$$

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    6
    141
    7.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • shattyundefined
      shatty @Veti
      last edited by shatty

      @Veti Hows this?

      ; Configuration file for Duet WiFi (firmware version 3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time)

      ; General preferences
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"E5Plus" ; set printer name

      ; Network
      M551 P"xxxxx" ; set password
      M552 S1 ; enable network
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S0 ; disable Telnet

      ; Drives
      M569 P0 S1 ; physical drive 0 goes forwards
      M569 P1 S1 ; physical drive 1 goes forwards
      M569 P2 S0 ; physical drive 2 goes backwards
      M569 P3 S0 ; physical drive 3 goes backwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X80.00 Y80.00 Z400.00 E412.60 ; set steps per mm
      M566 X1200.00 Y1200.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
      M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
      M906 X800 Y800 Z1400 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X350 Y350 Z400 S0 ; set axis maxima

      ; Endstops
      M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
      M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
      M574 Z1 S2 ; configure Z-probe endstop for low end on Z

      ; Z-Probe
      M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
      M558 P9 C"^zprobe.in" H5 F600 T6000 ; set Z probe type to bltouch and the dive height + speeds
      G31 P500 X16.3 Y14 Z1.7 ; set Z probe trigger value, offset and trigger height
      M557 X15:190 Y15:190 S20 ; define mesh grid

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 C4700 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S110 ; set temperature limit for heater 0 to 110C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4092 C4700 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S1 H1 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings are not defined

      ; Miscellaneous
      M575 P1 S1 B57600 ; enable support for PanelDue

      I dont see where the Heater for the hot end should max at 280. Also there are 2 fans on the hot end. Shouldnt the values be identical? I got a lot of the fixes from someones 5 Pro config

      Phaedruxundefined 1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator @shatty
        last edited by

        @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

        I dont see where the Heater for the hot end should max at 280.

        Add M143 H1 S280 at the end of the heater block under the M307.

        Otherwise I don't see any obvious issues.

        You can send M98 P"config.g" in the console to see if there are any syntax errors.

        Otherwise it's time to do some testing.

        Z-Bot CoreXY Build | Thingiverse Profile

        1 Reply Last reply Reply Quote 0
        • Vetiundefined
          Veti
          last edited by

          @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

          M92 X80.00 Y80.00 Z400.00 E412.60 ; set steps per mm

          as i posted earlier the Z steps according to marlin are Z800

          M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 C4700 ; configure sensor 0 as thermistor on pin bedtemp
          M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
          M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
          M140 H0 ; map heated bed to heater 0
          M143 H0 S110 ; set temperature limit for heater 0 to 110C
          M308 S1 P"e0temp" Y"thermistor" T100000 B4092 C4700 ; configure sensor 1 as thermistor on pin e0temp

          delete the C4700 thats not the resistance. you can leave R empty and the correct default is choosen.

          1 Reply Last reply Reply Quote 1
          • shattyundefined
            shatty
            last edited by

            @Phaedrux said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

            M143 H1 S280

            OK so I edited and turned on.

            Seems ok. Temps are hovering at 22 deg C with heaters off.
            Motors are F'ed up. Z looks good. Its the X and Y. I got some error codes.

            11/16/2020, 1:18:45 AM M122
            === Diagnostics ===
            RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
            Board ID: 08DLM-996RU-N8PS0-6J1DJ-3SD6K-KSSHN
            Used output buffers: 3 of 24 (11 max)
            === RTOS ===
            Static ram: 27980
            Dynamic ram: 93672 of which 44 recycled
            Exception stack ram used: 264
            Never used ram: 9112
            Tasks: NETWORK(ready,384) HEAT(blocked,1224) MAIN(running,1880) IDLE(ready,80)
            Owned mutexes: WiFi(NETWORK)
            === Platform ===
            Last reset 00:04:52 ago, cause: software
            Last software reset time unknown, reason: User, spinning module GCodes, available RAM 8240 bytes (slot 1)
            Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
            Error status: 0
            MCU temperature: min 24.7, current 25.6, max 26.1
            Supply voltage: min 24.1, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
            Driver 0: standstill, SG min/max not available
            Driver 1: standstill, SG min/max not available
            Driver 2: standstill, SG min/max not available
            Driver 3: standstill, SG min/max not available
            Driver 4: standstill, SG min/max not available
            Date/time: 2020-11-16 01:18:41
            Cache data hit count 507426640
            Slowest loop: 6.91ms; fastest: 0.12ms
            I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
            === Storage ===
            Free file entries: 10
            SD card 0 detected, interface speed: 20.0MBytes/sec
            SD card longest read time 3.8ms, write time 0.0ms, max retries 0
            === Move ===
            Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
            Bed compensation in use: none, comp offset 0.000
            === MainDDARing ===
            Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
            === AuxDDARing ===
            Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
            === Heat ===
            Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
            === GCodes ===
            Segments left: 0
            Movement lock held by null
            HTTP is idle in state(s) 0
            Telnet is idle in state(s) 0
            File is idle in state(s) 0
            USB is idle in state(s) 0
            Aux is idle in state(s) 0
            Trigger is idle in state(s) 0
            Queue is idle in state(s) 0
            Daemon is idle in state(s) 0
            Autopause is idle in state(s) 0
            Code queue is empty.
            === Network ===
            Slowest loop: 15.88ms; fastest: 0.00ms
            Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
            HTTP sessions: 1 of 8

            • WiFi -
              Network state is active
              WiFi module is connected to access point
              Failed messages: pending 0, notready 0, noresp 0
              WiFi firmware version 1.23
              WiFi MAC address f4:cf:a2:66:99:4f
              WiFi Vcc 3.38, reset reason Unknown
              WiFi flash size 4194304, free heap 23640
              WiFi IP address 192.168.2.8
              WiFi signal strength -43dBm, reconnections 0, sleep mode modem
              Socket states: 0 0 0 0 0 0 0 0
              11/16/2020, 1:17:30 AM M120 G91 G1 X-1 F6000 G90 M121
              Error: G0/G1: insufficient axes homed
              11/16/2020, 1:14:17 AM Connection established
              11/16/2020, 1:13:42 AM Connection interrupted, attempting to reconnect...
              11/16/2020, 1:13:32 AM Emergency Stop! Reset the controller to continue.
              11/16/2020, 1:13:32 AM Emergency stop, attemping to reconnect...
              11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
              11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
              11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
              11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2
              11/16/2020, 1:13:16 AM Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
              11/16/2020, 1:13:07 AM Connection established
              11/16/2020, 1:12:52 AM Connection interrupted, attempting to reconnect...
              HTTP request timed out
              11/16/2020, 1:12:40 AM Upload of config.g successful after 0s
              11/16/2020, 1:07:50 AM Connected to 192.168.2.8
            Vetiundefined 2 Replies Last reply Reply Quote 0
            • shattyundefined
              shatty
              last edited by shatty

              ; Configuration file for Duet WiFi (firmware version 3)
              ; executed by the firmware on start-up
              ;
              ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time)

              ; General preferences
              G90 ; send absolute coordinates...
              M83 ; ...but relative extruder moves
              M550 P"E5Plus" ; set printer name

              ; Network
              M551 P"xxxxx" ; set password
              M552 S1 ; enable network
              M586 P0 S1 ; enable HTTP
              M586 P1 S0 ; disable FTP
              M586 P2 S0 ; disable Telnet

              ; Drives
              M569 P0 S1 ; physical drive 0 goes forwards
              M569 P1 S1 ; physical drive 1 goes forwards
              M569 P2 S0 ; physical drive 2 goes backwards
              M569 P3 S0 ; physical drive 3 goes backwards
              M584 X0 Y1 Z2 E3 ; set drive mapping
              M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
              M92 X80.00 Y80.00 Z800.00 E412.60 ; set steps per mm
              M566 X1200.00 Y1200.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
              M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
              M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
              M906 X800 Y800 Z1400 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent
              M84 S30 ; Set idle timeout

              ; Axis Limits
              M208 X0 Y0 Z0 S1 ; set axis minima
              M208 X350 Y350 Z400 S0 ; set axis maxima

              ; Endstops
              M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
              M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
              M574 Z1 S2 ; configure Z-probe endstop for low end on Z

              ; Z-Probe
              M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
              M558 P9 C"^zprobe.in" H5 F600 T6000 ; set Z probe type to bltouch and the dive height + speeds
              G31 P500 X16.3 Y14 Z1.7 ; set Z probe trigger value, offset and trigger height
              M557 X15:190 Y15:190 S20 ; define mesh grid

              ; Heaters
              M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
              M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
              M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
              M140 H0 ; map heated bed to heater 0
              M143 H0 S110 ; set temperature limit for heater 0 to 110C
              M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
              M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
              M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
              M143 H1 S280 ; 280 deg max on hot end

              ; Fans
              M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
              M106 P0 S1 H1 ; set fan 0 value. Thermostatic control is turned off
              M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
              M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

              ; Tools
              M563 P0 D0 H1 F0 ; define tool 0
              G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
              G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

              ; Custom settings are not defined

              ; Miscellaneous
              M575 P1 S1 B57600 ; enable support for PanelDue

              1 Reply Last reply Reply Quote 0
              • shattyundefined
                shatty
                last edited by shatty

                @Phaedrux said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                M98 P"config.g"

                11/16/2020, 1:23:54 AM M98 P"config.g"
                HTTP is enabled on port 80
                FTP is disabled
                TELNET is disabled
                Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C

                I have that little daughter board connected for the bed heat. Looks like a relay board. Bed heat output on D3D connects to smaller board. Looks like the bed heat output triggers that smaller board. But if you think I should connect the bed straight to bed out on D3D I will

                1 Reply Last reply Reply Quote 0
                • Vetiundefined
                  Veti @shatty
                  last edited by

                  @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                  11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
                  11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
                  11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
                  11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2

                  this indicates that your wiring of the phases are incorrect.

                  see
                  https://duet3d.dozuki.com/Wiki/Choosing_and_connecting_stepper_motors#Section_Connecting_stepper_motors

                  shattyundefined 2 Replies Last reply Reply Quote 0
                  • shattyundefined
                    shatty @Veti
                    last edited by

                    @Veti said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                    @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                    11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
                    11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
                    11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
                    11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2

                    this indicates that your wiring of the phases are incorrect.

                    see
                    https://duet3d.dozuki.com/Wiki/Choosing_and_connecting_stepper_motors#Section_Connecting_stepper_motors

                    I triple checked them. I compared from the stock board to the D3D. I will check again

                    1 Reply Last reply Reply Quote 0
                    • shattyundefined
                      shatty @Veti
                      last edited by shatty

                      @Veti
                      so just Extruder,x and y? And just the B phase?

                      Vetiundefined 1 Reply Last reply Reply Quote 0
                      • dc42undefined
                        dc42 administrators
                        last edited by

                        As it's only one phase of each driver that's reported as disconnected, a likely cause is a bad crimp connection.

                        Duet WiFi hardware designer and firmware engineer
                        Please do not ask me for Duet support via PM or email, use the forum
                        http://www.escher3d.com, https://miscsolutions.wordpress.com

                        1 Reply Last reply Reply Quote 0
                        • Vetiundefined
                          Veti @shatty
                          last edited by

                          @shatty

                          M584 X0 Y1 Z2

                          x y z, presumably you have not moved the extruder.

                          the stock board config does not matter, as each board has different layouts.

                          did you follow the guide to find the phases of the motors?

                          shattyundefined 1 Reply Last reply Reply Quote 0
                          • shattyundefined
                            shatty @Veti
                            last edited by

                            @Veti The stock board has the terminals labeled for the ab and 12. I compared them to D3D and it was good.

                            shattyundefined dc42undefined 2 Replies Last reply Reply Quote 0
                            • shattyundefined
                              shatty @shatty
                              last edited by shatty

                              @shatty Motors are 6 pin. The 2 inner and 2 outer are used. Dunno if that matters

                              Vetiundefined 1 Reply Last reply Reply Quote 0
                              • Vetiundefined
                                Veti @shatty
                                last edited by

                                @shatty

                                thats normal

                                shattyundefined 1 Reply Last reply Reply Quote 0
                                • shattyundefined
                                  shatty @Veti
                                  last edited by shatty

                                  This post is deleted!
                                  1 Reply Last reply Reply Quote 0
                                  • dc42undefined
                                    dc42 administrators @shatty
                                    last edited by dc42

                                    @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                                    @Veti The stock board has the terminals labeled for the ab and 12. I compared them to D3D and it was good.

                                    If you used the same wiring order for the stepper motor connectors on the Duet as they were on the old board, then it should be correct. All boards that I know of put the wires for one phase at one end of the connector, and the other phase at the other end.

                                    If you did have the phases incorrectly wired, the error messages would be different.

                                    So IMO the most likely cause is a bad crimp connection. I suggest you use a multimeter to measure the resistance of each phase from the connector on the Duet.

                                    Duet WiFi hardware designer and firmware engineer
                                    Please do not ask me for Duet support via PM or email, use the forum
                                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                                    shattyundefined 1 Reply Last reply Reply Quote 0
                                    • shattyundefined
                                      shatty @dc42
                                      last edited by shatty

                                      @dc42

                                      OK what about homing? It keeps trying to go past the limits. Every direction. Where do i move manually the axis?

                                      1 Reply Last reply Reply Quote 0
                                      • shattyundefined
                                        shatty
                                        last edited by

                                        I havent received any errors for the phases lately

                                        1 Reply Last reply Reply Quote 0
                                        • shattyundefined
                                          shatty
                                          last edited by

                                          M98 P"0:/macros/01-Test_IR_PD_Homing"
                                          Error: in file macro line 12 column 30: M906: array too long, max length = 1
                                          Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.

                                          1 Reply Last reply Reply Quote 0
                                          • shattyundefined
                                            shatty
                                            last edited by shatty

                                            The endstops are not telling the unit to stop moving. It hits the endstop switch and it still tries to move in that direction. But the endstops are functioning because I went to settings and machine specific and when i press them, the value changes

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA