Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Newbie: New Install on Ender 5 Plus---Willing to PAY$$$

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    6
    141
    7.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • shattyundefined
      shatty
      last edited by

      @Phaedrux said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

      M143 H1 S280

      OK so I edited and turned on.

      Seems ok. Temps are hovering at 22 deg C with heaters off.
      Motors are F'ed up. Z looks good. Its the X and Y. I got some error codes.

      11/16/2020, 1:18:45 AM M122
      === Diagnostics ===
      RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
      Board ID: 08DLM-996RU-N8PS0-6J1DJ-3SD6K-KSSHN
      Used output buffers: 3 of 24 (11 max)
      === RTOS ===
      Static ram: 27980
      Dynamic ram: 93672 of which 44 recycled
      Exception stack ram used: 264
      Never used ram: 9112
      Tasks: NETWORK(ready,384) HEAT(blocked,1224) MAIN(running,1880) IDLE(ready,80)
      Owned mutexes: WiFi(NETWORK)
      === Platform ===
      Last reset 00:04:52 ago, cause: software
      Last software reset time unknown, reason: User, spinning module GCodes, available RAM 8240 bytes (slot 1)
      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
      Error status: 0
      MCU temperature: min 24.7, current 25.6, max 26.1
      Supply voltage: min 24.1, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
      Driver 0: standstill, SG min/max not available
      Driver 1: standstill, SG min/max not available
      Driver 2: standstill, SG min/max not available
      Driver 3: standstill, SG min/max not available
      Driver 4: standstill, SG min/max not available
      Date/time: 2020-11-16 01:18:41
      Cache data hit count 507426640
      Slowest loop: 6.91ms; fastest: 0.12ms
      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
      === Storage ===
      Free file entries: 10
      SD card 0 detected, interface speed: 20.0MBytes/sec
      SD card longest read time 3.8ms, write time 0.0ms, max retries 0
      === Move ===
      Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
      Bed compensation in use: none, comp offset 0.000
      === MainDDARing ===
      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
      === AuxDDARing ===
      Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
      === Heat ===
      Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
      === GCodes ===
      Segments left: 0
      Movement lock held by null
      HTTP is idle in state(s) 0
      Telnet is idle in state(s) 0
      File is idle in state(s) 0
      USB is idle in state(s) 0
      Aux is idle in state(s) 0
      Trigger is idle in state(s) 0
      Queue is idle in state(s) 0
      Daemon is idle in state(s) 0
      Autopause is idle in state(s) 0
      Code queue is empty.
      === Network ===
      Slowest loop: 15.88ms; fastest: 0.00ms
      Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
      HTTP sessions: 1 of 8

      • WiFi -
        Network state is active
        WiFi module is connected to access point
        Failed messages: pending 0, notready 0, noresp 0
        WiFi firmware version 1.23
        WiFi MAC address f4:cf:a2:66:99:4f
        WiFi Vcc 3.38, reset reason Unknown
        WiFi flash size 4194304, free heap 23640
        WiFi IP address 192.168.2.8
        WiFi signal strength -43dBm, reconnections 0, sleep mode modem
        Socket states: 0 0 0 0 0 0 0 0
        11/16/2020, 1:17:30 AM M120 G91 G1 X-1 F6000 G90 M121
        Error: G0/G1: insufficient axes homed
        11/16/2020, 1:14:17 AM Connection established
        11/16/2020, 1:13:42 AM Connection interrupted, attempting to reconnect...
        11/16/2020, 1:13:32 AM Emergency Stop! Reset the controller to continue.
        11/16/2020, 1:13:32 AM Emergency stop, attemping to reconnect...
        11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
        11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
        11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
        11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2
        11/16/2020, 1:13:16 AM Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
        11/16/2020, 1:13:07 AM Connection established
        11/16/2020, 1:12:52 AM Connection interrupted, attempting to reconnect...
        HTTP request timed out
        11/16/2020, 1:12:40 AM Upload of config.g successful after 0s
        11/16/2020, 1:07:50 AM Connected to 192.168.2.8
      Vetiundefined 2 Replies Last reply Reply Quote 0
      • shattyundefined
        shatty
        last edited by shatty

        ; Configuration file for Duet WiFi (firmware version 3)
        ; executed by the firmware on start-up
        ;
        ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time)

        ; General preferences
        G90 ; send absolute coordinates...
        M83 ; ...but relative extruder moves
        M550 P"E5Plus" ; set printer name

        ; Network
        M551 P"xxxxx" ; set password
        M552 S1 ; enable network
        M586 P0 S1 ; enable HTTP
        M586 P1 S0 ; disable FTP
        M586 P2 S0 ; disable Telnet

        ; Drives
        M569 P0 S1 ; physical drive 0 goes forwards
        M569 P1 S1 ; physical drive 1 goes forwards
        M569 P2 S0 ; physical drive 2 goes backwards
        M569 P3 S0 ; physical drive 3 goes backwards
        M584 X0 Y1 Z2 E3 ; set drive mapping
        M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
        M92 X80.00 Y80.00 Z800.00 E412.60 ; set steps per mm
        M566 X1200.00 Y1200.00 Z60.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
        M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
        M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
        M906 X800 Y800 Z1400 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent
        M84 S30 ; Set idle timeout

        ; Axis Limits
        M208 X0 Y0 Z0 S1 ; set axis minima
        M208 X350 Y350 Z400 S0 ; set axis maxima

        ; Endstops
        M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
        M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
        M574 Z1 S2 ; configure Z-probe endstop for low end on Z

        ; Z-Probe
        M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
        M558 P9 C"^zprobe.in" H5 F600 T6000 ; set Z probe type to bltouch and the dive height + speeds
        G31 P500 X16.3 Y14 Z1.7 ; set Z probe trigger value, offset and trigger height
        M557 X15:190 Y15:190 S20 ; define mesh grid

        ; Heaters
        M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
        M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
        M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
        M140 H0 ; map heated bed to heater 0
        M143 H0 S110 ; set temperature limit for heater 0 to 110C
        M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
        M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
        M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
        M143 H1 S280 ; 280 deg max on hot end

        ; Fans
        M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
        M106 P0 S1 H1 ; set fan 0 value. Thermostatic control is turned off
        M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
        M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

        ; Tools
        M563 P0 D0 H1 F0 ; define tool 0
        G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
        G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

        ; Custom settings are not defined

        ; Miscellaneous
        M575 P1 S1 B57600 ; enable support for PanelDue

        1 Reply Last reply Reply Quote 0
        • shattyundefined
          shatty
          last edited by shatty

          @Phaedrux said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

          M98 P"config.g"

          11/16/2020, 1:23:54 AM M98 P"config.g"
          HTTP is enabled on port 80
          FTP is disabled
          TELNET is disabled
          Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C

          I have that little daughter board connected for the bed heat. Looks like a relay board. Bed heat output on D3D connects to smaller board. Looks like the bed heat output triggers that smaller board. But if you think I should connect the bed straight to bed out on D3D I will

          1 Reply Last reply Reply Quote 0
          • Vetiundefined
            Veti @shatty
            last edited by

            @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

            11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
            11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
            11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
            11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2

            this indicates that your wiring of the phases are incorrect.

            see
            https://duet3d.dozuki.com/Wiki/Choosing_and_connecting_stepper_motors#Section_Connecting_stepper_motors

            shattyundefined 2 Replies Last reply Reply Quote 0
            • shattyundefined
              shatty @Veti
              last edited by

              @Veti said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

              @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

              11/16/2020, 1:13:31 AM Warning: motor phase B may be disconnected reported by driver(s) 2
              11/16/2020, 1:13:26 AM Warning: motor phase B may be disconnected reported by driver(s) 2
              11/16/2020, 1:13:22 AM Warning: motor phase B may be disconnected reported by driver(s) 2
              11/16/2020, 1:13:17 AM Warning: motor phase B may be disconnected reported by driver(s) 0 1 2

              this indicates that your wiring of the phases are incorrect.

              see
              https://duet3d.dozuki.com/Wiki/Choosing_and_connecting_stepper_motors#Section_Connecting_stepper_motors

              I triple checked them. I compared from the stock board to the D3D. I will check again

              1 Reply Last reply Reply Quote 0
              • shattyundefined
                shatty @Veti
                last edited by shatty

                @Veti
                so just Extruder,x and y? And just the B phase?

                Vetiundefined 1 Reply Last reply Reply Quote 0
                • dc42undefined
                  dc42 administrators
                  last edited by

                  As it's only one phase of each driver that's reported as disconnected, a likely cause is a bad crimp connection.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • Vetiundefined
                    Veti @shatty
                    last edited by

                    @shatty

                    M584 X0 Y1 Z2

                    x y z, presumably you have not moved the extruder.

                    the stock board config does not matter, as each board has different layouts.

                    did you follow the guide to find the phases of the motors?

                    shattyundefined 1 Reply Last reply Reply Quote 0
                    • shattyundefined
                      shatty @Veti
                      last edited by

                      @Veti The stock board has the terminals labeled for the ab and 12. I compared them to D3D and it was good.

                      shattyundefined dc42undefined 2 Replies Last reply Reply Quote 0
                      • shattyundefined
                        shatty @shatty
                        last edited by shatty

                        @shatty Motors are 6 pin. The 2 inner and 2 outer are used. Dunno if that matters

                        Vetiundefined 1 Reply Last reply Reply Quote 0
                        • Vetiundefined
                          Veti @shatty
                          last edited by

                          @shatty

                          thats normal

                          shattyundefined 1 Reply Last reply Reply Quote 0
                          • shattyundefined
                            shatty @Veti
                            last edited by shatty

                            This post is deleted!
                            1 Reply Last reply Reply Quote 0
                            • dc42undefined
                              dc42 administrators @shatty
                              last edited by dc42

                              @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                              @Veti The stock board has the terminals labeled for the ab and 12. I compared them to D3D and it was good.

                              If you used the same wiring order for the stepper motor connectors on the Duet as they were on the old board, then it should be correct. All boards that I know of put the wires for one phase at one end of the connector, and the other phase at the other end.

                              If you did have the phases incorrectly wired, the error messages would be different.

                              So IMO the most likely cause is a bad crimp connection. I suggest you use a multimeter to measure the resistance of each phase from the connector on the Duet.

                              Duet WiFi hardware designer and firmware engineer
                              Please do not ask me for Duet support via PM or email, use the forum
                              http://www.escher3d.com, https://miscsolutions.wordpress.com

                              shattyundefined 1 Reply Last reply Reply Quote 0
                              • shattyundefined
                                shatty @dc42
                                last edited by shatty

                                @dc42

                                OK what about homing? It keeps trying to go past the limits. Every direction. Where do i move manually the axis?

                                1 Reply Last reply Reply Quote 0
                                • shattyundefined
                                  shatty
                                  last edited by

                                  I havent received any errors for the phases lately

                                  1 Reply Last reply Reply Quote 0
                                  • shattyundefined
                                    shatty
                                    last edited by

                                    M98 P"0:/macros/01-Test_IR_PD_Homing"
                                    Error: in file macro line 12 column 30: M906: array too long, max length = 1
                                    Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.

                                    1 Reply Last reply Reply Quote 0
                                    • shattyundefined
                                      shatty
                                      last edited by shatty

                                      The endstops are not telling the unit to stop moving. It hits the endstop switch and it still tries to move in that direction. But the endstops are functioning because I went to settings and machine specific and when i press them, the value changes

                                      1 Reply Last reply Reply Quote 0
                                      • shattyundefined
                                        shatty
                                        last edited by

                                        This post is deleted!
                                        1 Reply Last reply Reply Quote 0
                                        • Vetiundefined
                                          Veti @shatty
                                          last edited by

                                          @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                                          11/16/2020, 1:13:16 AM Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.

                                          this means that your homing files were created for an old version of the firmware.

                                          please generate new ones from the configurator.

                                          shattyundefined 1 Reply Last reply Reply Quote 0
                                          • shattyundefined
                                            shatty @Veti
                                            last edited by shatty

                                            @Veti everything came from same zip. Every file except config.g and *.txt have same time stamps

                                            Vetiundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA