Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Newbie: New Install on Ender 5 Plus---Willing to PAY$$$

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    6
    141
    7.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Vetiundefined
      Veti @shatty
      last edited by

      @shatty

      thats normal

      shattyundefined 1 Reply Last reply Reply Quote 0
      • shattyundefined
        shatty @Veti
        last edited by shatty

        This post is deleted!
        1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators @shatty
          last edited by dc42

          @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

          @Veti The stock board has the terminals labeled for the ab and 12. I compared them to D3D and it was good.

          If you used the same wiring order for the stepper motor connectors on the Duet as they were on the old board, then it should be correct. All boards that I know of put the wires for one phase at one end of the connector, and the other phase at the other end.

          If you did have the phases incorrectly wired, the error messages would be different.

          So IMO the most likely cause is a bad crimp connection. I suggest you use a multimeter to measure the resistance of each phase from the connector on the Duet.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          shattyundefined 1 Reply Last reply Reply Quote 0
          • shattyundefined
            shatty @dc42
            last edited by shatty

            @dc42

            OK what about homing? It keeps trying to go past the limits. Every direction. Where do i move manually the axis?

            1 Reply Last reply Reply Quote 0
            • shattyundefined
              shatty
              last edited by

              I havent received any errors for the phases lately

              1 Reply Last reply Reply Quote 0
              • shattyundefined
                shatty
                last edited by

                M98 P"0:/macros/01-Test_IR_PD_Homing"
                Error: in file macro line 12 column 30: M906: array too long, max length = 1
                Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.

                1 Reply Last reply Reply Quote 0
                • shattyundefined
                  shatty
                  last edited by shatty

                  The endstops are not telling the unit to stop moving. It hits the endstop switch and it still tries to move in that direction. But the endstops are functioning because I went to settings and machine specific and when i press them, the value changes

                  1 Reply Last reply Reply Quote 0
                  • shattyundefined
                    shatty
                    last edited by

                    This post is deleted!
                    1 Reply Last reply Reply Quote 0
                    • Vetiundefined
                      Veti @shatty
                      last edited by

                      @shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:

                      11/16/2020, 1:13:16 AM Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.

                      this means that your homing files were created for an old version of the firmware.

                      please generate new ones from the configurator.

                      shattyundefined 1 Reply Last reply Reply Quote 0
                      • shattyundefined
                        shatty @Veti
                        last edited by shatty

                        @Veti everything came from same zip. Every file except config.g and *.txt have same time stamps

                        Vetiundefined 1 Reply Last reply Reply Quote 0
                        • Vetiundefined
                          Veti @shatty
                          last edited by

                          @shatty

                          post your homeall.g

                          1 Reply Last reply Reply Quote 0
                          • shattyundefined
                            shatty
                            last edited by

                            ; homeall.g
                            ; called to home all axes
                            ;
                            ; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time)
                            G91 ; relative positioning
                            G1 H2 Z5 F6000 ; lift Z relative to current position
                            G1 H1 X-355 Y-355 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
                            G1 H2 X5 Y5 F6000 ; go back a few mm
                            G1 H1 X-355 Y-355 F360 ; move slowly to X and Y axis endstops once more (second pass)
                            G90 ; absolute positioning
                            G1 X-1.3000000000000007 Y1 F6000 ; go to first bed probe point and home Z
                            G30 ; home Z by probing the bed

                            ; Uncomment the following lines to lift Z after probing
                            ;G91 ; relative positioning
                            ;G1 Z5 F100 ; lift Z relative to current position
                            ;G90 ; absolute positioning

                            Vetiundefined 1 Reply Last reply Reply Quote 0
                            • Vetiundefined
                              Veti @shatty
                              last edited by

                              @shatty

                              ok then the problem is in

                              01-Test_IR_PD_Homing

                              post that.
                              where did you get that macro?

                              shattyundefined 1 Reply Last reply Reply Quote 0
                              • shattyundefined
                                shatty
                                last edited by

                                Recycling is tomorrow. Is the printer recyclable?

                                1 Reply Last reply Reply Quote 0
                                • shattyundefined
                                  shatty @Veti
                                  last edited by

                                  @Veti Dunno

                                  E5Plus
                                  Send code...
                                  Status
                                  Idle
                                  Mode: FFF
                                  Tool Position
                                  X
                                  0.0
                                  Y
                                  0.0
                                  Z
                                  0.00
                                  Extruder Drives
                                  Drive 0
                                  0.0
                                  Speeds
                                  Requested Speed
                                  0 mm/s
                                  Top Speed
                                  0 mm/s
                                  Sensors
                                  Vin
                                  24.3 V
                                  MCU Temperature
                                  25.9 C
                                  Z-Probe
                                  0
                                  Tools
                                  Extra
                                  Control All
                                  Tool Heater Current Active Standby
                                  Tool 0
                                  T0 - Load Filament Heater 1
                                  off 22.4 C
                                  0
                                  0
                                  Bed Heater 0
                                  off 21.9 C
                                  0
                                  0
                                  Temperature Chart
                                  Macros Directory
                                  0:/macros/01-Test_IR_PD_Homing
                                  ; Test Routine for Duet WiFi and Ethernet June 2018 - Check IR Probe, PanelDue and endstops

                                  ;Start logging
                                  M929 P"test1log.txt" S1

                                  M117 CHECK IR PROBE & PANELDUE THEN PRESS X ENDSTOP.
                                  M577 X S2 ; wait for endstop to trigger
                                  M577 X S0 ; wait for endstop release

                                  ;----setup motors for test----
                                  M906 X2000 Y2000 Z2000 E2000:2000 I100 ;set all motors to 2A with no idle current reduction

                                  ;----homing line (tests endstops)----
                                  M117 PRESS ALL THREE ENDSTOPS TO END HOMING
                                  G91 ; use relative positioning
                                  G1 S1 X3200 Y3200 Z3200 F9000 ; move XYZ motors, stopping when endstops are triggered
                                  ;----end homing lines----

                                  M117 GO ON TO TEST 02

                                  Vetiundefined 1 Reply Last reply Reply Quote 0
                                  • shattyundefined
                                    shatty
                                    last edited by

                                    The endless moving happens when I press home all and each axis independently

                                    1 Reply Last reply Reply Quote 0
                                    • Vetiundefined
                                      Veti @shatty
                                      last edited by

                                      @shatty
                                      please dont use that macro, its not for your printer

                                      1 Reply Last reply Reply Quote 0
                                      • Vetiundefined
                                        Veti
                                        last edited by

                                        use M119

                                        https://duet3d.dozuki.com/Wiki/Gcode#Section_M119_Get_Endstop_Status

                                        to manually test your endstops.

                                        if you can not get them to trigger, there is a problem with your wiring.

                                        shattyundefined 1 Reply Last reply Reply Quote 0
                                        • shattyundefined
                                          shatty @Veti
                                          last edited by shatty

                                          @Veti I tested endstops already under settings and machine specific. X and Y work

                                          1 Reply Last reply Reply Quote 0
                                          • Vetiundefined
                                            Veti
                                            last edited by

                                            G1 X-1.3000000000000007 Y1 F6000 ; go to first bed probe point and home Z

                                            replace that with

                                            G1 X50 Y50 F600

                                            when exactly does it try to move past the endstops?
                                            during the first move?

                                            shattyundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA