Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    ToolBoard: 2 wires fan, heater fault and how to extrude ?

    Scheduled Pinned Locked Moved Unsolved
    Duet Hardware and wiring
    6
    112
    5.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Pseud3mysundefined
      Pseud3mys @Veti
      last edited by

      @Veti ok, yes it both version 3.1.1

      1 Reply Last reply Reply Quote 0
      • Pseud3mysundefined
        Pseud3mys @Veti
        last edited by

        @Veti I tried to update the toolBoard but I go this error:

        02/12/2020 à 18:23:25	Upload of Duet3Firmware_TOOL1LC.bin successful after 1s
        02/12/2020 à 18:23:27	M997 B122
        Board 122 starting firmware update
        02/12/2020 à 18:23:37	M997 S
        Error: Failed to switch off remote heater 2: Board 122 does not have heater 2
        02/12/2020 à 18:23:39	Error: Failed to switch off remote heater 2: Board 122 does not have heater 2
        02/12/2020 à 18:24:06	Connection established
        
        Vetiundefined 1 Reply Last reply Reply Quote 0
        • Pseud3mysundefined
          Pseud3mys
          last edited by

          I seem to have update it.. no error. But the version it's still 3.1.0 (on the toolboard 1LC). but I download the 3.1.1 (git hub)

          1 Reply Last reply Reply Quote 0
          • Vetiundefined
            Veti @Pseud3mys
            last edited by

            3.1.0 is correct there is no 3.1.1 for the toolboard.

            Pseud3mysundefined 1 Reply Last reply Reply Quote 0
            • Pseud3mysundefined
              Pseud3mys @Veti
              last edited by

              @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

              3.1.0 is correct there is no 3.1.1 for the toolboard.

              ah ok. Have you an idea then for the fault state ?

              1 Reply Last reply Reply Quote 0
              • Vetiundefined
                Veti
                last edited by Veti

                @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                Error: Failed to switch off remote heater 2: Board 122 does not have heater 2

                do you still get this error message?

                Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                • Pseud3mysundefined
                  Pseud3mys @Veti
                  last edited by

                  @Veti no, when I update it now it just put "2000°C" and offline on the web site but he is still connected with the CAN bus

                  1 Reply Last reply Reply Quote 0
                  • Vetiundefined
                    Veti
                    last edited by

                    post the output of
                    M122 B121
                    and
                    M122 B122

                    Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                    • Pseud3mysundefined
                      Pseud3mys @Veti
                      last edited by

                      @Veti Capture.PNG

                      1 Reply Last reply Reply Quote 0
                      • Vetiundefined
                        Veti
                        last edited by

                        you power down the system after the firmware update?

                        also power the normal M122 output

                        Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                        • Pseud3mysundefined
                          Pseud3mys @Veti
                          last edited by

                          @Veti yes, what is the M122 output ?

                          1 Reply Last reply Reply Quote 0
                          • Vetiundefined
                            Veti
                            last edited by

                            i meant provide the m122 output

                            Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                            • Pseud3mysundefined
                              Pseud3mys @Veti
                              last edited by

                              @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                              i meant provide the m122 output

                              it was not this ?

                              @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                              @Veti Capture.PNG

                              1 Reply Last reply Reply Quote 0
                              • Vetiundefined
                                Veti
                                last edited by

                                no just send M122. that will provide the output for the duet 3

                                Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                • Pseud3mysundefined
                                  Pseud3mys @Veti
                                  last edited by

                                  @Veti ah okay, the popup say "response too long, see console"
                                  02/12/2020 à 19:08:20 M122
                                  === Diagnostics ===
                                  RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (standalone mode)
                                  Board ID: 08DJM-956BA-NA3TJ-6J1D2-3SD6M-9B9LT
                                  Used output buffers: 1 of 40 (23 max)
                                  === RTOS ===
                                  Static ram: 154604
                                  Dynamic ram: 162588 of which 36 recycled
                                  Exception stack ram used: 224
                                  Never used ram: 75764
                                  Tasks: NETWORK(ready,292) ETHERNET(blocked,436) HEAT(blocked,1248) CanReceiv(suspended,3404) CanSender(suspended,1488) CanClock(blocked,1436) TMC(blocked,204) MAIN(running,4520) IDLE(ready,76)
                                  Owned mutexes: LwipCore(NETWORK)
                                  === Platform ===
                                  Last reset 00:00:54 ago, cause: software
                                  Last software reset at 2020-12-02 19:07, reason: User, spinning module GCodes, available RAM 75728 bytes (slot 2)
                                  Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
                                  Error status: 0
                                  MCU temperature: min 36.6, current 37.0, max 37.6
                                  Supply voltage: min 12.2, current 12.3, max 12.3, under voltage events: 0, over voltage events: 0, power good: yes
                                  12V rail voltage: min 11.4, current 11.4, max 11.5, under voltage events: 0
                                  Driver 0: standstill, reads 6703, writes 0 timeouts 0, SG min/max not available
                                  Driver 1: standstill, reads 6704, writes 0 timeouts 0, SG min/max not available
                                  Driver 2: standstill, reads 6702, writes 0 timeouts 0, SG min/max not available
                                  Driver 3: standstill, reads 6702, writes 0 timeouts 0, SG min/max not available
                                  Driver 4: standstill, reads 6702, writes 0 timeouts 0, SG min/max not available
                                  Driver 5: standstill, reads 6701, writes 0 timeouts 0, SG min/max not available
                                  Date/time: 2020-12-02 19:08:18
                                  Slowest loop: 6.33ms; fastest: 0.22ms
                                  === Storage ===
                                  Free file entries: 10
                                  SD card 0 detected, interface speed: 25.0MBytes/sec
                                  SD card longest read time 2.2ms, write time 0.0ms, max retries 0
                                  === Move ===
                                  Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
                                  Bed compensation in use: none, comp offset 0.000
                                  === MainDDARing ===
                                  Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
                                  === AuxDDARing ===
                                  Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
                                  === Heat ===
                                  Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
                                  === GCodes ===
                                  Segments left: 0
                                  Movement lock held by null
                                  HTTP is idle in state(s) 0
                                  Telnet is idle in state(s) 0
                                  File is idle in state(s) 0
                                  USB is idle in state(s) 0
                                  Aux is idle in state(s) 0
                                  Trigger is idle in state(s) 0
                                  Queue is idle in state(s) 0
                                  LCD is idle in state(s) 0
                                  SBC is idle in state(s) 0
                                  Daemon is idle in state(s) 0
                                  Aux2 is idle in state(s) 0
                                  Autopause is idle in state(s) 0
                                  Code queue is empty.
                                  === Network ===
                                  Slowest loop: 5.59ms; fastest: 0.03ms
                                  Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
                                  HTTP sessions: 1 of 8

                                  • Ethernet -
                                    State: active
                                    Error counts: 0 0 0 0 0
                                    Socket states: 5 2 2 2 2 0 0 0
                                    === CAN ===
                                    Messages sent 59, longest wait 0ms for type 0
                                    === Linux interface ===
                                    State: 0, failed transfers: 0
                                    Last transfer: 54276ms ago
                                    RX/TX seq numbers: 0/1
                                    SPI underruns 0, overruns 0
                                    Number of disconnects: 0
                                    Buffer RX/TX: 0/0-0
                                  1 Reply Last reply Reply Quote 0
                                  • Vetiundefined
                                    Veti
                                    last edited by

                                    hmm can communication seems to be working.

                                    can you update to the latest beta as the diagnostic has been improved.

                                    Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                    • Pseud3mysundefined
                                      Pseud3mys @Veti
                                      last edited by

                                      @Veti can we update duet with M997 ?

                                      1 Reply Last reply Reply Quote 0
                                      • Pseud3mysundefined
                                        Pseud3mys
                                        last edited by

                                        I have:
                                        Error: M997: In-application programming binary "Duet3_SDiap_MB6HC.bin" not found
                                        but there is not this file in the repository ? (git hub )

                                        1 Reply Last reply Reply Quote 0
                                        • Vetiundefined
                                          Veti
                                          last edited by

                                          find that file here
                                          https://github.com/Duet3D/RepRapFirmware/releases/tag/3.0

                                          Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                          • Pseud3mysundefined
                                            Pseud3mys @Veti
                                            last edited by Pseud3mys

                                            This post is deleted!
                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA