Toolboard Heater Tuning and Fan Error

[Frederik]

@Veti

19.12.2020, 14:47:20	
 
m122 b121
 
Diagnostics for board 121:
Duet TOOL1LC firmware version 3.2-beta4.1 (2020-12-03)
Bootloader ID: not available
Never used RAM 4180, free system stack 84 words
HEAT 50 CanAsync 89 CanRecv 83 TMC 54 MAIN 218 AIN 64
Last reset 00:24:45 ago, cause: VDD brownout
Last software reset data not available
Driver 0: position 0, 830.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 12, reads 21603, writes 12, timeouts 0, DMA errors 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.1V
MCU temperature: min 43.5C, current 43.6C, max 46.0C
Ticks since heat task active 54, ADC conversions started 1479264, completed 1479263, timed out 0
Last sensors broadcast 0x00000002 found 1 58 ticks ago, loop time 0
CAN messages queued 18185, send timeouts 0, received 13832, lost 0, free buffers 36
 

[Veti]

the bootloader not the firmware. please read the thread.

[jay_s_uk]

Is it to do with the BLtouch being on the toolboard but the z drivers being on the main board?
I believe the restriction is still in place about the probe being in a different board

[Frederik]

@Veti yes , but it says bootloader not available, and i cant find the file. i Have to update via can, do i need the ToolLc1 firmware also or only the bootloader file ?

[Veti]

whats the error message when you issue the bootloader update?

the bootloader files are here as its written in the documentation.
https://github.com/Duet3D/Duet3Bootloader/releases

[Frederik]

@Veti bootloader not found

I looked again in the toolboard documentation, but i cant find the link to the bootloader, there is only a link to GitHub with the step files....

do i need only the samc21.bin or the .elf file also?

any additional files needed?

i added the 3 lines for the workaround also to the end of my config.g

i will test if now the mesh completes without errors

[Frederik]

@Veti the samc21 from your link worked.

m997 b121 s3

Board 121 starting bootloader update

19.12.2020, 15:45:56 Datei Duet3Bootloader-SAMC21.bin erfolgreich nach 0s hochgeladen

now, i´m really curious what the bltouch does

[Frederik]

@Veti
after the update :

m122 b121
Diagnostics for board 121:
Duet TOOL1LC firmware version 3.2-beta4.1 (2020-12-03)
Bootloader ID: SAMC21 bootloader version 2.1 (2020-11-03b2)
Never used RAM 4668, free system stack 96 words
HEAT 50 CanAsync 89 CanRecv 83 TMC 54 MAIN 338 AIN 64
Last reset 00:02:38 ago, cause: software
Last software reset data not available
Driver 0: position 0, 80.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 22, reads 13732, writes 9, timeouts 0, DMA errors 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.1V
MCU temperature: min 42.0C, current 42.0C, max 42.3C
Ticks since heat task active 85, ADC conversions started 158578, completed 158577, timed out 0
Last sensors broadcast 0x00000000 found 0 88 ticks ago, loop time 0
CAN messages queued 16, send timeouts 0, received 1436, lost 0, free buffers 36

Is that the right combination of firmwares ?
i am using DWC 3.2.0beta4

m122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta4.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956BA-NA3TN-6J9DL-3S46S-99AUT
Used output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 123292
Dynamic ram: 139216 of which 140 recycled
Never used RAM 129544, free system stack 126 words
Tasks: Linux(ready,101) HEAT(blocked,272) CanReceiv(blocked,829) CanSender(blocked,352) CanClock(blocked,352) TMC(blocked,20) MAIN(running,669) IDLE(ready,19)
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:23:02 ago, cause: power up
Last software reset at 2020-12-19 15:22, reason: User, none spinning, available RAM 129752, slot 0
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0xffffffff Task Linu
Error status: 0x00
MCU temperature: min 27.7, current 31.2, max 42.6
Supply voltage: min 24.0, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: position 72800, standstill, reads 18438, writes 31 timeouts 0, SG min/max 0/248
Driver 1: position 4000, standstill, reads 18439, writes 31 timeouts 0, SG min/max 0/244
Driver 2: position 6400, standstill, reads 18440, writes 31 timeouts 0, SG min/max 0/246
Driver 3: position 0, standstill, reads 18440, writes 31 timeouts 0, SG min/max 0/245
Driver 4: position 0, standstill, reads 18441, writes 31 timeouts 0, SG min/max 0/244
Driver 5: position 0, standstill, reads 18459, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2020-12-19 15:51:23
Slowest loop: 182.07ms; fastest: 0.09ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
FreeDm 375 (min 372), maxWait 436239ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 49, completed moves 49, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 3 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0: no data received
=== CAN ===
Messages queued 5738, send timeouts 0, received 12611, lost 0, longest wait 3ms for reply type 6049, free buffers 47
=== SBC interface ===
State: 0, failed transfers: 0
Last transfer: 19ms ago
RX/TX seq numbers: 47923/47924
SPI underruns 0, overruns 0
Number of disconnects: 0, IAP RAM available 0x209d8
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.2.0-beta4
Code buffer space: 4096
Configured SPI speed: 8000000 Hz
Full transfers per second: 30.23
 

[Frederik]

@Veti the bootloader doesent make a big difference

this time, it completes perhaps 40% of my build area bevor it stops and starts blinking.

the workaround lines of code are also in place....

[Stephen6309]

@Frederik You could try a lower speed in M558. I use 6000.

[Frederik]

@Stephen6309 i will try, moment

[Veti]

you could also try adjusting the grub screw on the top of the bltouch.

[Frederik]

@Stephen6309 speed to 6000 - same error

@Veti one moment , i will try

[Frederik]

@Veti i changed the mesh size from 20mm to 75mm and it completed the whole area without error.

[Frederik]

@Veti how can i delete a used thermistor pin ?

since the last change of my config.g , i get a heater fault and open circuit, but the cables are ok

[Veti]

@Frederik said in Toolboard Heater Tuning and Fan Error:

how can i delete a used thermistor pin ?

dont define it the in the config.

[Frederik]

@Veti i deleted it already, my heated bed is ok. the thermistor has 100.8k resistance , but i cant get them to wrok after the config change

[Veti]

post the changes you made

[Frederik]

@Veti i removed the chamber heater

; Heaters
M308 S0 P"temp0" Y"thermistor" T10000 B4100                  ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                           ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                                             ; disable bang-bang mode for the bed heater and set PWM limitd                                                   ; map heated bed to heater 0
M143 H0 S150  
M308 S1 P"121.temp0" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 1 as thermistor on pin 121.temp0
M950 H1 C"121.out0" T1                                       ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 B0 S1.00                                             ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S500     

but i get -273°C

[Frederik]

@Veti

eeven if i conmect a brand new e3d thermistor i get the -273 reading

; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.10 on Sat Dec 19 2020 18:27:02 GMT+0100 (Mitteleuropäische Normalzeit)
 
; General preferences
G90                                                          ; send absolute coordinates...
M83                                                          ; ...but relative extruder moves
M550 P"vcore"                                               ; set printer name
M669 K1                                                      ; select CoreXY mode
 
; Drives
M569 P0.0 S1                                                 ; physical drive 0.0 goes forwards
M569 P0.1 S1                                                 ; physical drive 0.1 goes forwards
M569 P0.2 S0                                                 ; physical drive 0.2 goes forwards
M569 P0.3 S0                                                 ; physical drive 0.5 goes forwards
M569 P0.4 S0                                                 ; physical drive 0.5 goes forwards
M569 P0.5 S0                                                 ; physical drive 0.5 goes forwards
M584 X0.0 Y0.1 Z0.2:0.3:0.4 E0.5                             ; set drive mapping
M350 X16 Y16 Z16 E16 I1                                          ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z800.00 E830.00                          ; set steps per mm
M566 X3000.00 Y3000.00 Z60.00 E1200.00                       ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z600.00 E1200.00                    ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E250.00                         ; set accelerations (mm/s^2)
M906 X1900 Y1900 Z1900 E800 I30                              ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                      ; Set idle timeout
 
M671 X0:200:400 Y50:385:50 S10 							     ; Position of Leadscrews
 
;Duet Laser Filament Monitor
;M591 D0 P5 C"io3.in" R30:130 E3.0 S0 				         ; Tolerance 30 to 130%, 3mm comparison length, diabled
 
 
; Pressure Advance Tuning
;M572 D0 S0.1												 ; Extruder pressure advance
 
; Cancel Ringing at the defined Freuquenzy
;M593 F40.5
 
 
; Axis Limits
M208 X0 Y0 Z0 S1                                             ; set axis minima
M208 X410 Y385 Z390 S0                                       ; set axis maxima
 
; Endstops
M574 X1 S1 P"121.io2.in"                                     ; configure active-high endstop for low end on X via pin 121.io2.in
M574 Y1 S1 P"io0.in"                                         ; configure active-high endstop for low end on Y via pin io0.in
M574 Z2 S2                                                   ; configure Z-probe endstop for high end on Z
 
; Z-Probe
M950 S0 C"121.io0.out"                                       ; create servo pin 0 for BLTouch
M558 P9 C"^121.io0.in" H5 F120 T6000                         ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z0                                            ; set Z probe trigger value, offset and trigger height
M557 X38:410 Y15:385 S40                                     ; define mesh grid
 
; Heaters
M308 S0 P"temp0" Y"thermistor" T10000 B4100                  ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                           ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                                             ; disable bang-bang mode for the bed heater and set PWM limitd                                                   ; map heated bed to heater 0
M143 H0 S150  
M308 S1 P"121.temp0" Y"thermistor" T500000 B4723 C1.19622e-7 ; configure sensor 1 as thermistor on pin 121.temp0
M950 H1 C"121.out0" T1                                       ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 B0 S1.00                                             ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S500     
 
; Fans
M950 F0 C"121.out2" Q500                                     ; create fan 0 on pin 121.out2 and set its frequency
M106 P0 C"Düse" S0 H-1                                       ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"121.out1" Q500                                     ; create fan 1 on pin 121.out1 and set its frequency
M106 P1 C"Bauteil" S0 H-1                                    ; set fan 1 name and value. Thermostatic control is turned off
 
; Tools
M563 P0 S"Mosquito Magnum" H1 F0:1                             ; define tool 0
G10 P0 X0 Y0 Z0                                              ; set tool 0 axis offsets
G10 P0 R0 S0                                                 ; set initial tool 0 active and standby temperatures to 0C
 
; Custom settings are not defined
M912 P0 S-14.8												 ; MCU Temperature Calibration
 
; Miscellaneous
;M501                                                         ; load saved parameters from non-volatile memory
;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"           ; set voltage thresholds and actions to run on power loss
T0                                                           ; select first tool
 
;M280 P0 S60 												 ; BLtouch - toggle switch mode
;G4 P1000 													 ; wait 1 second
;M280 P0 S120 												 ; BLtouch toggle self-test