Help with setup - solved

RonP

indeed, i have done it twice some places even more.
But the step that i am stuck at is Commissioning step 4 the light never comes on .

=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L2MS8-6JKFJ-3S86Q-TBGGN
Used output buffers: 3 of 24 (8 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 92584 of which 416 recycled
Exception stack ram used: 272
Never used ram: 12088
Tasks: NETWORK(ready,896) HEAT(blocked,1232) MAIN(running,3816) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:26:01 ago, cause: power up
Last software reset at 2021-01-10 18:59, reason: User, spinning module GCodes, available RAM 12000 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 33.3, current 42.2, max 42.6
Supply voltage: min 24.8, current 24.9, max 25.0, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-01-11 01:44:13
Cache data hit count 4294967295
Slowest loop: 2.11ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.66ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address dc:4f:22:6e:e4:db
WiFi Vcc 3.46, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25136
WiFi IP address 192.168.1.20
WiFi signal strength -46dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0

Phaedrux

Does anything on the smart effector light up?

Photos of the wiring?

RonP

Yep the print lights come on on the points.
Wiring is really messy rewired so please don't hold it against me
.

jay_s_uk

it helps if you add power to the effector...

jay_s_uk

there should be cables here

RonP

@jay_s_uk hey Jay, those are for the thermistor.
They were there and still didn't work.

jay_s_uk

no, T1 to T4 are the thermistor.
If thats the case, you are feeding power into the thermistor connections.
I suggest you revisit the wiring diagram

RonP

@jay_s_uk Thanks good catch, switched it. Looks like I need to redo the black 6 pin . Heading to bed. Thank you for taking the time to get me on the right path.

RonP

So everything has been redone.
Print lights are working, fans come on as expected, heater cartridge and thermistor work.
tried to power on using usb still no green light.

jay_s_uk

@RonP can you post your config.g?

RonP

@jay_s_uk will be a couple of hours. Had to take dog to the vet.️

RonP

config.g
Here it is

RonP

@jay_s_uk Here you go
config.g

Veti

M305 P0 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 0
M305 P1 T100000 B4138 R4700 ; set thermistor + ADC parameters for heater 1

B4138 is the default and wrong for your thermistor. look up the correct value in your thermistor documentation

also add a T0 to the end of your config. (is "Select the First Tool on Start-Up" in the configurator)

you also might want to enable "Read config-override.g file at end of startup process (provides similar functionality to the EEPROM option in Marlin)"
makes the calibration for a delta easier.

jay_s_uk

@RonP I can't see anything there that would stop the smart effector from working (i just compared it against my old RRF2 with smart effector config).
What voltage are you working with? 12v or 24v?

RonP

@jay_s_uk 24v

jay_s_uk

@RonP not sure what else I can add then.
I would use a multimeter just to check everything out once more.

RonP

@jay_s_uk hey Jay, went through it all again and it seems good. So does that mean my effector is bad ?
Thanks for taking the time to help me.

jay_s_uk

@RonP I think for @Phaedrux to be able to answer that, he'll be after clear photos of the top and the bottom of the board, ideally without anything attached.
Can you also comment on when and where you purchased it?

dc42

If the green light on the Smart Effector never comes on at all, even at power up, the most likely reason is that it is not getting 3.3V and ground through the 8-pin connector.