Changing pt100 to standard thermistor

[Stephen6309]

@Atraedes You need a M510 at the end of config,g.

[Atraedes]

thanks, tried it, it says "Warning: M510 command is not supported"

[Phaedrux]

https://duet3d.dozuki.com/Wiki/Gcode#Section_M500_Store_parameters

M500 saves to config-override.g, and M501 loads it. You need to add M501 to the end of config.g to load the saved values at startup.

[Atraedes]

the sd card is buried deep in the machine also so i cant easily get to it without taking the bottom of etc.., i just assumed i could do everything via the console?

[Stephen6309]

@Atraedes Oops, i ment M501. The keyboard keeps reversing things.

[Atraedes]

thanks again, so i made the changes you advised straight to the config files incl the config in sys folder on the sd card, loaded back into the machine, then ran pid tune, got this - "Auto tune heater 0 completed in 1489 sec
Use M307 H0 to see the result, or M500 to save the result in config-override.g", but then when i entered M500 via the console it answered - "M500
Warning: No M501 command was executed in config.g". Did i do something wrong?

[Atraedes]

i then tried M501, and got this - "M501
Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 692C.", feels like im back to square one lol, but the whole hotend, cables and all, are new, and confirmed 24v

[Veti]

@Atraedes said in Changing pt100 to standard thermistor:

Warning: No M501 command was executed in config.g". Did i do something wrong?

add M501 to the end of your config.g

[Atraedes]

so remove the SD card from the machine and type M501 at the very end of the config file? Can i not send that via the console?

[Veti]

@Atraedes
just edit the file using the web ui

[Atraedes]

sorry i dont know how to do that, im still learning the ropes with the duet3d board i have

[Veti]

please read

https://duet3d.dozuki.com/Wiki/Duet_Web_Control_Manual

[Phaedrux]

Oh wow, I didn't realize you weren't even connected to the web interface yet.

https://duet3d.dozuki.com/Guide/1.)+Getting+Connected+to+your+Duet/7

It definitely makes a world of difference.

[Atraedes]

so if i understood correctly, ive gone into system in the web ui, found config.g, opened and typed M501 at the end of the file, and its asking if do i want to reset the board and apply the update? is that correct?

[Atraedes]

no sorry, i probably didnt explain, i am using the web ui, all the time,and running these commands via the console in the web ui, but i thought it was a simple M500 via the console in web ui to save it, and it doesnt

[Phaedrux]

Yes you have to edit config.g and add M501 at the end.

As I said, M500 saves SOME settings (like PID tuning or other measured values) to the file config-override.g. And M501 loads that files.

https://duet3d.dozuki.com/Wiki/Gcode#Section_M500_Store_parameters

[Atraedes]

@Atraedes said in Changing pt100 to standard thermistor:

gone into system in the web ui, found config.g, opened and typed M501 at the end of the file, and its asking if do i want to reset the board and apply the update?

ok thanks, so to try solve these spurious heating faults, run my pid tune, after it shows results then go into system in the web ui, into config.g, M501 at the end of the file, and reset the board and apply the update?

[Phaedrux]

@Atraedes said in Changing pt100 to standard thermistor:

Warning: Heater 1 appears to be over-powered. If left on at full power, its temperature is predicted to reach 692C.",

That's not a heater fault. It's a warning.

https://duet3d.dozuki.com/Wiki/FAQ#Section_M307_Heater_1_appears_to_be_over_powered_If_left_on_at_full_power_its_temperature_is_predicted_to_reach_521C

[Phaedrux]

PID tune, send M500 in console, add M501 to config.g. done.

[Atraedes]

awesome thanks, much appreciated