Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    mesh leveling help

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    4
    14
    416
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • usas12undefined
      usas12
      last edited by

      Hi,

      Thanks for the reply, Yep straight to the deep end for me, thank god for forums. It's in the "Z stop"

      1 Reply Last reply Reply Quote 0
      • usas12undefined
        usas12 @Phaedrux
        last edited by

        @Phaedrux

        I have this

        ; Endstops
        M574 X1 Y1 S3 ; Set X / Y endstop stall detection
        M574 Z1 S1 P"zstop" ; Set Z endstop probe
        M558 P7 X0 Y0 Z2 H3 F360 I0 T20000 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds
        G31 P200 X0 Y0 Z0 ; Set Z probe trigger value, offset and trigger height
        M557 X10:290 Y20:180 S40 ; Define mesh grid

        on a G29 S0 call I'm getting the Error: z probe 0 not found.
        The switch works fine when homing

        I've tried adding
        ; Z-Probe
        M558 P7 C"^Zstop" H5 F120 T6000

        Same result: z probe 0 not found.

        o_lampeundefined 1 Reply Last reply Reply Quote 0
        • o_lampeundefined
          o_lampe @usas12
          last edited by

          @usas12 said in mesh leveling help:

          I've tried adding
          ; Z-Probe
          M558 P7 C"^Zstop" H5 F120 T6000

          Maybe it's zstop**.in**?
          Just guessing...

          Phaedruxundefined 1 Reply Last reply Reply Quote 0
          • usas12undefined
            usas12
            last edited by

            found out that v3+ firmware cannot have a Zstop work as a end stop and a probe.

            So I tried this
            ; Endstops
            M574 X1 S3 ; Set X endstop stall detection
            M574 Y1 S3 ; Set Y endstop stall detection

            M574 Z0 P"nil" ; No Z endstop @used by DC42 using G30 homing
            M558 P8 C"zstop" H5 F120 T10000 A5 S0.01 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds @DC42
            G31 Z0 ; Set Z probe trigger value, offset and trigger height
            M557 X4:292 Y4:185 S16:15 ; Set Z probe: Define mesh grid

            M574 C1 S3 ; Stall detect coupler at low end of its range

            Still getting the "z probe 0 not found" error message

            1 Reply Last reply Reply Quote 0
            • jay_s_ukundefined
              jay_s_uk
              last edited by

              Can you confirm you are running RRF3 by sending and posting the output of M115.

              Also remove

              M574 Z0 P"nil" ; No Z endstop @used by DC42 using G30 homing

              as its not required

              Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

              usas12undefined 1 Reply Last reply Reply Quote 1
              • usas12undefined
                usas12
                last edited by

                This post is deleted!
                1 Reply Last reply Reply Quote 0
                • usas12undefined
                  usas12 @jay_s_uk
                  last edited by

                  @jay_s_uk 6d185893-5d7a-453c-ac32-48364acc348f-image.png

                  1 Reply Last reply Reply Quote 1
                  • jay_s_ukundefined
                    jay_s_uk
                    last edited by

                    @usas12
                    If you run

                    M98 P"config.g"

                    Any errors should be shown.
                    Can you also post your full config file.

                    Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                    usas12undefined 1 Reply Last reply Reply Quote 0
                    • usas12undefined
                      usas12 @jay_s_uk
                      last edited by

                      @jay_s_uk said in mesh leveling help:

                      M98 P"config.g"

                      G21 ; Work in millimetres
                      G90 ; Send absolute coordinates...
                      M83 ; ...but relative extruder moves
                      M555 P2 ; Set firmware compatibility to look like Marlin

                      ; Network
                      ; Read https://duet3d.dozuki.com/Wiki/Gcode#Section_M587_Add_WiFi_host_network_to_remembered_list_or_list_remembered_networks
                      M550 P"ToolChanger" ; Set machine name
                      M552 S1 ; Enable Networking
                      M586 P0 S1 ; Enable HTTP
                      M586 P1 S0 ; Disable FTP
                      M586 P2 S0 ; Disable Telnet

                      M667 S1 ; Select CoreXY mode

                      ; Endstops
                      M574 X1 Y1 S3 ; Set X / Y endstop stall detection
                      M574 Z1 S2 ; Set Z endstop probe
                      M558 P7 X0 Y0 Z2 H3 F360 I0 T20000 ; Set Z probe type to switch, the axes for which it is used and the dive height + speeds
                      G31 P200 X0 Y0 Z0 ; Set Z probe trigger value, offset and trigger height
                      M557 X10:290 Y20:180 S40 ; Define mesh grid

                      ; Drive direction
                      M569 P0 S0 ; Drive 0 X
                      M569 P1 S0 ; Drive 1 Y
                      M569 P2 S1 ; Drive 2 Z
                      M569 P3 S0 ; Drive 3 E0
                      M569 P4 S0 ; Drive 4 E1
                      M569 P5 S1 ; Drive 5 E2
                      M569 P6 S1 ; Drive 6 E3
                      M569 P7 S0 ; Drive 7 COUPLER
                      M569 P8 S0 ; Drive 8 UNUSED
                      M569 P9 S0 ; Drive 9 UNUSED

                      M584 X0 Y1 Z2 C7 E3:4:5:6 ; Apply custom drive mapping
                      M208 X-35:328.5 Y-49:243 Z0:300 C0:260 S0 ; Set axis maxima & minima
                      M350 C8 I0 ; Configure microstepping without interpolation
                      M350 X16 Y16 Z16 E16:16:16:16 I1 ; Configure microstepping with interpolation
                      M92 X100 Y100 Z1600 C100 E834:834:834:834 ; Set steps per mm
                      M566 X400 Y400 Z8 C2 E2:2:2:2 ; Set maximum instantaneous speed changes (mm/min)
                      M203 X35000 Y35000 Z1200 C5000 E5000:5000:5000:5000 ; Set maximum speeds (mm/min)
                      M201 X6000 Y6000 Z400 C400 E2500:2500:2500:2500 ; Set accelerations (mm/s^2)
                      M906 X2000 Y2000 Z1330 C400 E1680:1680:1680:1680 I30 ; Set motor currents (mA) and motor idle factor in percent
                      M84 S120 ; Set idle timeout

                      ;Stall Detection
                      M915 C S5 F0 H200 ; Coupler

                      ;Stall Detection
                      M915 X Y S5 F0 H400 ; X / Y Axes

                      ; Heaters
                      M305 P0 T100000 B4725 C7.06e-8 ; Set thermistor
                      M143 H0 S225 ; Set temperature limit for heater 0 to 225C

                      M305 S"T0" P1 T100000 B4725 C7.06e-8 ; Set thermistor
                      M143 H1 S300 ; Set temperature limit for heater 1 to 300C

                      M305 S"T1" P2 T100000 B4725 C7.06e-8 ; Set thermistor
                      M143 H2 S300 ; Set temperature limit for heater 2 to 300C

                      M305 S"T2" P3 T100000 B4725 C7.06e-8 ;Set thermistor
                      M143 H3 S300 ; Set temperature limit for heater 3 to 300C

                      M305 S"T3" P4 T100000 B4725 C7.06e-8 ; Set thermistor
                      M143 H4 S300 ; Set temperature limit for heater 4 to 300C

                      ; Tools
                      M563 P0 S"T0" D0 H1 F2 ; Define tool 0
                      G10 P0 X0 Y0 Z0 ; Reset tool 0 axis offsets
                      G10 P0 R0 S0 ; Reset initial tool 0 active and standby temperatures to 0C

                      M563 P1 S"T1" D1 H2 F4 ; Define tool 1
                      G10 P1 X0 Y0 Z0 ; Reset tool 1 axis offsets
                      G10 P1 R0 S0 ; Reset initial tool 1 active and standby temperatures to 0C

                      M563 P2 S"T2" D2 H3 F6 ; Define tool 2
                      G10 P2 X0 Y0 Z0 ; Reset tool 2 axis offsets
                      G10 P2 R0 S0 ; Reset initial tool 2 active and standby temperatures to 0C

                      M563 P3 S"T3" D3 H4 F8 ; Define tool 3
                      G10 P3 X0 Y0 Z0 ; Reset tool 3 axis offsets
                      G10 P3 R0 S0 ; Reset initial tool 3 active and standby temperatures to 0C

                      ; Fans
                      M106 P0 S0 ; UNUSED
                      M106 P1 S255 H1 T70 ; T0 HE
                      M106 P2 S0 ; T0 PCF
                      M106 P3 S255 H2 T70 ; T1 HE
                      M106 P4 S0 ; T1 PCF
                      M106 P5 S255 H3 T70 ; T2 HE
                      M106 P6 S0 ; T2 PCF
                      M106 P7 S255 H4 T70 ; T3 HE
                      M106 P8 S0 ; T3 PCF

                      M593 F50 ; cancel ringing at 50Hz (https://forum.e3d-online.com/threads/accelerometer-and-resonance-measurements-of-the-motion-system.3445/)
                      ;M376 H15 ; bed compensation taper

                      ;tool offsets
                      ; !ESTIMATED! offsets for:
                      ; V6-tool: X-9 Y39 Z-5
                      ; Volcano-tool: X-9 Y39 Z-13.5
                      ; Hemera-tool: X-37.5 Y43.5 Z-6

                      G10 P0 X-9 Y39 Z-5 ; T0
                      G10 P1 X-9 Y39 Z-5 ; T1
                      G10 P2 X-9 Y39 Z-5 ; T2
                      G10 P3 X-9 Y39 Z-5 ; T3

                      ;deselect tools
                      T-1

                      ;M572 D0 S0.2 ; pressure advance T0
                      ;M572 D1 S0.2 ; pressure advance T1
                      ;M572 D2 S0.2 ; pressure advance T2
                      ;M572 D3 S0.2 ; pressure advance T3

                      M501; load config-override.g

                      1 Reply Last reply Reply Quote 0
                      • jay_s_ukundefined
                        jay_s_uk
                        last edited by

                        @usas12

                        The config you have posted is for RRF2.
                        I suggest you look at these files https://github.com/Duet3D/RRF-machine-config-files/tree/master/E3D_Tool_Changer/dc42-wifi-centreZero-quadTitan

                        Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                        usas12undefined 1 Reply Last reply Reply Quote 1
                        • usas12undefined
                          usas12 @jay_s_uk
                          last edited by

                          @jay_s_uk WOW that made a big difference, Thank you!

                          1 Reply Last reply Reply Quote 0
                          • Phaedruxundefined
                            Phaedrux Moderator @o_lampe
                            last edited by

                            @o_lampe said in mesh leveling help:

                            @usas12 said in mesh leveling help:

                            I've tried adding
                            ; Z-Probe
                            M558 P7 C"^Zstop" H5 F120 T6000

                            Maybe it's zstop**.in**?
                            Just guessing...

                            Nope. zstop is correct in this case. https://duet3d.dozuki.com/Wiki/RepRapFirmware_3_overview#Section_Pin_names

                            Z-Bot CoreXY Build | Thingiverse Profile

                            1 Reply Last reply Reply Quote 0
                            • First post
                              Last post
                            Unless otherwise noted, all forum content is licensed under CC-BY-SA