Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    New to the duet COMPLETE NEWBIE

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    5
    101
    5.5k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • fcwiltundefined
      fcwilt
      last edited by

      It's late here (11:30 EST) and I need to turn in. We can take this up tomorrow.

      I'm working on my 6th, 7th and 8th printer.

      Even so I still take it one step at a time.

      Step one is always to get the WiFi working so I have access to the DWC where I can do the rest of the configuration.

      Then I connect one piece of hardware at a time and verify that it is working as expected - that stepper motors turn, end stop switches work correctly, fans run, heaters heat, etc.

      By doing that when something doesn't work I know exactly where I need to look for the problem.

      Frederick

      Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

      1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator @gabrealek
        last edited by

        @gabrealek said in New to the duet COMPLETE NEWBIE:

        @Phaedrux I inverted it and it went down so far it cracked the glass . 😞

        Ah nuts. Sorry about that.

        I'm wondering if your Z endstop wiring is not correct.

        Regardless of the ! being there or not, if it's electrically connected to the Duet it should report as stopped/not stopped and change state if the switch is actually clicked at the time when you send M119.

        Can you post a photo of the endstop wiring at the board? The creality endstops should be wired to the 2 outside pins of the endstop connector.

        Z-Bot CoreXY Build | Thingiverse Profile

        gabrealekundefined 1 Reply Last reply Reply Quote 1
        • gabrealekundefined
          gabrealek @Phaedrux
          last edited by

          @Phaedrux its okay. I can always get another . no worries.

          FBBD4AF8-67B0-4289-8905-04E91CAECE6B.jpeg

          0957704C-724C-4E9F-A316-BAF26191A0DE.jpeg

          423C1AE5-EE24-4836-B992-0D90C2A58C38.jpeg

          F9489D47-9EA1-4136-84B9-320C16092876.jpeg

          51B023E7-570D-4341-BC9B-A41C1A1366BB.jpeg

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator
            last edited by

            Ok, I can mostly see the endstops and they all look like they are connected correctly with the wires going to the outside pins, so that's a good start.

            Now to make sure the wires are actually connected electrically.

            Send M119 and see what the Z stop says.
            Then hold down the Z switch and send M119 again while holding it clicked and see if the status changes.

            Z-Bot CoreXY Build | Thingiverse Profile

            gabrealekundefined 1 Reply Last reply Reply Quote 0
            • gabrealekundefined
              gabrealek @Phaedrux
              last edited by

              @Phaedrux

              Its being so mean 😂

              1/22/2021, 4:44:48 PM M119
              Endstops - X: not stopped, Y: not stopped, Z: not stopped, Z probe: at min stop
              1/22/2021, 4:44:33 PM M119
              Endstops - X: not stopped, Y: not stopped, Z: not stopped, Z probe: at min stop

              1 Reply Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator
                last edited by

                So being clicked or not it's not registering? Just as a control, text the other endstops as well.

                If that is the case that pressing the endstop isn't registering at all then there could be a break in the wire or poor connection. In which case reseating the z endstop plug on the board may help. If you have a multimeter you can check the wire for continuity and whether the endstop switch will complete or break a circuit.

                Z-Bot CoreXY Build | Thingiverse Profile

                gabrealekundefined 1 Reply Last reply Reply Quote 0
                • gabrealekundefined
                  gabrealek @Phaedrux
                  last edited by

                  @Phaedrux
                  Okay. So how would i test with a multimeter? As in where to on the Z? Im still new at using this multimeter , ill post a pic to know exactly which setting to set it to. Also which command do i sent to test only for Z? THANKKASSSS621C9C88-A4C3-4363-9EB1-286D307B0B1E.jpeg

                  1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator
                    last edited by

                    This might help.

                    https://www.youtube.com/watch?v=OOK8np4t40c&ab_channel=HelpfulDIY

                    When set to ohms (orange on the left side, infact the symbol below the 600 may be intended specifically for continuity the arrow and the beep symbol), you can touch the two probe tips together and the display number should change, and maybe beep. Meaning there is a connection between them. Touch something metal and it should do the same. Touch two ends of a wire, same thing.

                    It will probably be easiest to remove the endstop from the printer entirely so that you can check the wire more easily. You'd basically want to touch one of the wires at the end that plugs into the printer, and the other end at the endstop itself.

                    Z-Bot CoreXY Build | Thingiverse Profile

                    gabrealekundefined 2 Replies Last reply Reply Quote 0
                    • gabrealekundefined
                      gabrealek @Phaedrux
                      last edited by

                      @Phaedrux

                      Yeahhh .. . so i think its the actual endstop. Its really wiggly. . i don't think its suppose to be this way . . i just ordered some new ones, and new cables to dead this whole issue. by the time i'm done ill probably have enough supplies for another printer.

                      1 Reply Last reply Reply Quote 0
                      • gabrealekundefined
                        gabrealek @Phaedrux
                        last edited by

                        @Phaedrux BUT THANK YOU THOUGH!! NOW I KNOW HOW TO USE IT THE RIGHT WAY. 🙂

                        1 Reply Last reply Reply Quote 0
                        • Phaedruxundefined
                          Phaedrux Moderator
                          last edited by

                          Hmm, yeah wiggly isn't great.

                          There is a way to get up and running without a Z endstop at all though. You can configure it to ask you to jog the print head down so that the nozzle touches the bed to set the Z height. Manual probing.

                          You'd need to change your config.g

                          M558 P0 H5 F300 T6000
                          G31 x0 y0 z0 P500
                          

                          And then in homeall and homez where it says

                          G1 H1 Z-405 F3000 ; move Z down until the endstop is triggered
                          G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
                          

                          replace that with

                          G1 X150 Y150 F6000
                          G30
                          

                          Then when you try and home it will do xy, move to the center(ish) and there will be a pop up asking you to move Z jog it down carefully and when the nozzle is just touching the bed, hit OK.

                          Pretty handy in cases like this. I used this the other week when I broke a BLTouch pin.

                          Z-Bot CoreXY Build | Thingiverse Profile

                          gabrealekundefined 2 Replies Last reply Reply Quote 0
                          • gabrealekundefined
                            gabrealek @Phaedrux
                            last edited by

                            This post is deleted!
                            1 Reply Last reply Reply Quote 0
                            • Phaedruxundefined
                              Phaedrux Moderator
                              last edited by

                              Haha, good luck with your first print.

                              Z-Bot CoreXY Build | Thingiverse Profile

                              gabrealekundefined 2 Replies Last reply Reply Quote 0
                              • gabrealekundefined
                                gabrealek @Phaedrux
                                last edited by

                                @Phaedrux
                                I am SO SCARED. . lol thanks for the luck . . I NEED ITTTT

                                1 Reply Last reply Reply Quote 0
                                • gabrealekundefined
                                  gabrealek @Phaedrux
                                  last edited by gabrealek

                                  @Phaedrux okay so do is erase something out of my config? or rather where do i put this into the config

                                  1 Reply Last reply Reply Quote 0
                                  • gabrealekundefined
                                    gabrealek @Phaedrux
                                    last edited by

                                    @Phaedrux said in New to the duet COMPLETE NEWBIE:

                                    M558 P0 H5 F300 T6000 G31 x0 y0 z0 P500

                                    Okay i think i see . .

                                    ; Z-Probe
                                    M558 P0 H18 F120 T480000 ; disable Z probe but set dive height, probe speed and travel speed
                                    M557 X10:220 Y10:220 S20 ; define mesh grid

                                    replace with

                                    M558 P0 H5 F300 T6000
                                    G31 x0 y0 z0 P500

                                    1 Reply Last reply Reply Quote 0
                                    • Phaedruxundefined
                                      Phaedrux Moderator
                                      last edited by

                                      Replace with:

                                      M558 P0 H5 F300 T6000
                                      G31 x0 y0 z0 P500
                                      M557 X10:220 Y10:220 S20 ; define mesh grid

                                      Z-Bot CoreXY Build | Thingiverse Profile

                                      gabrealekundefined Phaedruxundefined 2 Replies Last reply Reply Quote 0
                                      • gabrealekundefined
                                        gabrealek @Phaedrux
                                        last edited by gabrealek

                                        @Phaedrux

                                        G91
                                        G1 H1 Z-400 F3000
                                        G92 Z0 ; change Z0 to match the actual Z co-ordinate at which the Z end stop triggers
                                        G1 Z10
                                        G1 H1 X-300 Y-300
                                        G1 X5 Y5
                                        G1 H1 X-6 Y-6 F300
                                        G90

                                        change to

                                        G91
                                        G1 X150 Y150 F6000
                                        G30
                                        Do i leave everything under this there or void?
                                        G1 Z10
                                        G1 H1 X-300 Y-300
                                        G1 X5 Y5
                                        G1 H1 X-6 Y-6 F300
                                        G90

                                        1 Reply Last reply Reply Quote 0
                                        • Phaedruxundefined
                                          Phaedrux Moderator
                                          last edited by

                                          For homeall try this

                                          G91 ; relative positioning
                                          G1 H2 Z5 F6000 ; lift Z relative to current position
                                          G1 H1 X-300 Y-300 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
                                          G1 X5 Y5 F6000 ; go back a few mm
                                          G1 H1 X-300 Y-300 F3600 ; move slowly to X and Y axis endstops once more (second pass)
                                          G90 ; absolute positioning
                                          G1 X150 Y150 F6000 ; move to center
                                          G30 ; probe the bed
                                          G1 X10 Y10 Z10 ; move to parking position
                                          

                                          Z-Bot CoreXY Build | Thingiverse Profile

                                          gabrealekundefined 1 Reply Last reply Reply Quote 0
                                          • gabrealekundefined
                                            gabrealek @Phaedrux
                                            last edited by

                                            @Phaedrux YESSS !! it worked perfectly!!

                                            1 Reply Last reply Reply Quote 2
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA